Equipment · Mumbai City district, Maharashtra
Protected cultivation equipment for Mumbai growers
By Editorial Team, Kryzen Biotech · Updated 13 November 2026
Mumbai protected cultivation needs equipment that handles two very different stresses: 38.4°C April afternoons with strong sun, then 2,509 mm of yearly rain and very humid June–October conditions. Polyhouse Constructions supplies complete material kits and individual polyhouse or nethouse parts from its Satara factory; erection is carried out by Kryzen Biotech’s construction team.
- Pad cooling
- Works: ~32°C inside
- Humid months
- 5
- Shading need
- High
- Delivery
- Next day

Choose equipment around Mumbai’s heat, humidity and rain
April is the critical heat month: the average afternoon high is 38.4°C and solar radiation reaches 7.1 kWh/m²/day. March is already warm at 36.8°C, while May remains at 37°C. A crop house planned only for shade can still hold unwanted heat, so the selection should combine shading with a planned route for air movement.
The monsoon changes the priority. Mumbai receives 535 mm in June, 834 mm in July, 606 mm in August and 376 mm in September. Humidity is 80% in June, 90% in July and August, and 89% in September. This makes rain collection, a secure covering, insect exclusion and circulation inside the house practical requirements rather than optional additions.
January has the coolest average night at 15.4°C. That is not a reason to specify extra night-heating equipment from this data; instead, check that the covering, profiles and fasteners are properly tensioned before the next hot and wet cycle.
- For April and May: exhaust-based cooling where required, plus white or aluminium shade net.
- For June to October: air circulation, working side ventilation, insect net integrity, wide gutters, funnels and a skirting apron.
- For November to February: this is Mumbai’s stated nethouse season; use the relatively drier period for structural checks and planned replacements.
| Need | For Mumbai | Why |
|---|---|---|
| Cooling | Exhaust fans + cellulose pads | Pads bring 38°C to ~32°C in April |
| Air movement | Air circulation fans | Humid from June to October |
| Shading | Aluminium or double-layer net | Sun peaks at 7.1 kWh/m² in April |
| Rain | Wide gutters, funnels, skirting apron | July: ~834 mm |
| Nights | No extra need | — |
Read the monthly weather before selecting a house
The climate table below is useful for deciding when equipment will be under greatest load. It shows why April needs solar and heat control, while July needs dependable rain handling even though its average high is only 28.4°C. Wind averages rise to 3.7 m/s in June and 4 m/s in July, another reason not to postpone inspection of film tension, clamps and gutters until the monsoon has begun.
For a naturally ventilated polyhouse (NVPH), use roll-up curtains and side insect net as part of the ventilation arrangement. For a fan-and-pad house, use the fan wall and pad side as the active cooling system. Square nethouses can use shade net and side insect net, while curved nethouses use shade net as an optional upgrade rather than polyfilm.
| Month | Afternoon high | Night low | Humidity | Rain | Sun (kWh/m²/day) | Wind (m/s) |
|---|---|---|---|---|---|---|
| Jan | 31°C | 15.4°C | 51% | 0 mm | 4.9 | 2 |
| Feb | 33.8°C | 17.6°C | 44% | 2 mm | 5.7 | 2.1 |
| Mar | 36.8°C | 20.6°C | 45% | 5 mm | 6.6 | 2.2 |
| Apr | 38.4°C | 23.1°C | 53% | 3 mm | 7.1 | 2.3 |
| May | 37°C | 25.4°C | 60% | 22 mm | 7.1 | 2.9 |
| Jun | 31.5°C | 25.8°C | 80% | 535 mm | 5 | 3.7 |
| Jul | 28.4°C | 24.9°C | 90% | 834 mm | 3.8 | 4 |
| Aug | 27.9°C | 24.2°C | 90% | 606 mm | 4 | 3.5 |
| Sep | 28.8°C | 23.6°C | 89% | 376 mm | 4.8 | 2.3 |
| Oct | 30.8°C | 21.6°C | 78% | 104 mm | 5.2 | 1.8 |
| Nov | 30.6°C | 18.6°C | 69% | 17 mm | 4.8 | 2 |
| Dec | 30.3°C | 16.3°C | 60% | 5 mm | 4.5 | 2 |
Does fan-and-pad cooling make sense in Mumbai?
It can work here: the available climate assessment puts a fan-and-pad house at about 32°C inside during April, compared with Mumbai’s 38.4°C average April high. That difference is relevant when the crop and crop calendar need a more controlled environment than a nethouse or an NVPH can provide.
Whether it pays is a farm decision, not something that can be answered from temperature alone. Compare the additional equipment and running requirement with the crop, selling window, crop quality requirement and your market route. Mumbai district market data shows seasonal variation: cucumber is highest in June at ₹2,758/q and lowest in March at ₹1,530/q; tomato is highest in December at ₹2,966/q and lowest in March at ₹1,382/q. These are market observations, not a promise of farm-gate price or profit.
For a first comparison, specify the system correctly. Exhaust fans and cellulose pads are standard fan-and-pad equipment; air-circulation fans are an optional upgrade in fan-and-pad and NVPH systems. Do not add fans without also planning pad frames, water-side maintenance and the installation layout.
- Exhaust Fan: ₹22,700 per piece + GST.
- Cellulose Pad (600X150X1800): ₹2,616 per piece + GST.
- Aluminium Pad Frame (150 mm): ₹815 per metre + GST.
- Air Circulation Fan: ₹8,999 per piece + GST.
A sizing reference before asking for a fan-and-pad quote
Equipment count depends on house dimensions and design, so a count from another farm should not be copied blindly. As a reference only, a 52 × 76 m fan-and-pad house measures 3,952 m² and uses 12 exhaust fans and 82 cellulose pads in the sizing figures below. The material including GST for that stated reference is ₹32,48,775.
Share the intended system, dimensions and crop when building a kit. Polyhouse Constructions supplies kits for NVPH, fan-and-pad polyhouses, square nethouses and curved nethouses. The online kit shows every item, quantity and that week’s rate, which is more useful than treating a generic per-unit figure as a final project cost.
- Fan & pad house, 52 × 76 m
- 3,952 m²
- Exhaust fans
- 12 nos
- Cellulose pads
- 82 nos
- Material incl. GST
- ₹32,48,775
Covering, ventilation and rain parts to prioritise
For a Mumbai NVPH or fan-and-pad house, 250-micron white diffused, UV-stabilised polyfilm is the primary covering option. It is listed at ₹254 per metre + GST for the 4.5 m product. A white 50% shade net is ₹27 per metre + GST, while the 4 m aluminium shade net is ₹315 per metre + GST; aluminium net is the reflective option to consider for the April sun peak.
Ventilation parts should be selected as a working set, not as isolated purchases. The Manual Gear Roll Up Curtain Unit is ₹1,050 per piece + GST, Curtain Pipe (27X2.0X6000) is ₹758 per piece + GST, Side Insect Net (5.2 m) is ₹221 per metre + GST, and a Curtain Clamp 0.75-inch is ₹11 per piece + GST. Side insect net is used in NVPH and square nethouse systems.
For monsoon runoff, the relevant NVPH and fan-and-pad items are GI Gutter Sheet at ₹335 per metre + GST, Gutter Funnel at ₹1,350 per piece + GST and Side Skirting Apron (1.5 m) at ₹64 per metre + GST. July’s 834 mm average rainfall is the reason to include these in planning rather than treat them as later repairs.
Plan maintenance around the Mumbai calendar
A short, month-specific care routine protects the equipment already installed. The calendar below starts before April because fans and pads need to be ready before the hottest average conditions, not after they arrive. It then moves to gutter, film and apron checks before July’s peak rain.
During the humid months, the aim is reliable air circulation and intact barriers. Keep the curtain mechanism usable, inspect insect net for tears, and do not let seasonal cleaning wait until crop problems are visible. In the drier November–February period, inspect fasteners and order consumables before the next demanding season.
- 1
Before April
Wash or replace cellulose pads, clean the pad gutter and filter, and check every exhaust fan belt and shutter before the 38°C peak.
- 2
Before July
Clear gutters and funnels, re-seat the side skirting apron and check film tension; July brings about 834 mm.
- 3
June to October
Run air circulation fans in the mornings, keep curtain gear units greased and check insect net for tears; humid air brings fungal disease and pests.
- 4
November to February
Tighten clamps and bolts, check GI springs in the aluminium profiles, and order replacement film or net before the next season.
Material quality, warranty and repair spares
The GI structure material uses ISI-marked branded steel from Tata, Jindal and JSW. In-house engineering and manufacturing are supported by a 32-point QA checklist, a technical data sheet for every product and lab test certificates with dispatch. The relevant checks include tensile testing of GI pipe steel, salt-spray testing for corrosion resistance and chemical analysis of steel composition; salt-spray performance is especially relevant to Mumbai’s humid conditions.
Warranty is 15 years on the GI structure, 2.5 years on polyfilm and 3 years on shade and insect nets. Confirm the part and warranty details with the technical data sheet supplied for the selected material.
A damaged net, curtain component, fan, pad or fitting does not require buying a complete kit. Every fan, pad, net and fitting is sold individually at the weekly rate for repair work and extensions. Rates follow weekly GI and plastic rates and are updated every Friday; a 5% bulk discount applies on 10 or more units of an item. Booking is with 5% advance and 95% before dispatch.
- Material is supplied from the Degaon, Pune–Bangalore Highway factory in Tal. Wai, Satara, Maharashtra; Mumbai delivery is 1 day after dispatch.
- Polyhouse Constructions does not have a Mumbai office. Construction or erection is done by Kryzen Biotech’s construction team.
- For growers around Mumbai, nearby locations include Navi Mumbai and Thane at 20 km, and Kalyan-Dombivli, Mira-Bhayandar and Panvel at 30 km.

Tensile test
Strength of the GI pipe steel, by a third-party lab.

Salt spray test
Corrosion resistance; worth it in humid Mumbai.

Chemical analysis
Spectrometer check of the steel composition.
| Part | Warranty |
|---|---|
| GI structure | 15 years |
| Polyfilm | 2.5 years |
| Shade and insect nets | 3 years |
Match crop timing with the Mumbai market, not only the structure
Protected equipment is a crop-management purchase as well as a structure purchase. Mumbai district market records cover three markets for green peas, beans, bottle gourd, bhindi, cucumber, green chilli, coriander, tomato and brinjal, and four markets for papaya. Use the seasonal pattern to ask when your likely harvest may meet stronger or weaker market observations.
Examples from the available data: green peas average ₹7,941/q and peak in May at ₹9,992/q; beans peak in June at ₹7,289/q; bhindi peaks in December at ₹5,685/q; green chilli peaks in January at ₹6,211/q; brinjal peaks in November at ₹3,415/q. Price history is not a guarantee, but it is a sounder starting point than choosing equipment without considering harvest timing and market access.
| Crop | Markets | Average modal price | Highest month | Lowest month |
|---|---|---|---|---|
| Green peas | 3 | ₹7,941/q | May (₹9,992) | Jan (₹5,150) |
| Beans | 3 | ₹4,301/q | Jun (₹7,289) | Feb (₹2,080) |
| Bottle gourd | 3 | ₹1,944/q | Jun (₹2,629) | Mar (₹1,403) |
| Okra (bhindi) | 3 | ₹4,406/q | Dec (₹5,685) | Apr (₹3,685) |
| Cucumber | 3 | ₹2,149/q | Jun (₹2,758) | Mar (₹1,530) |
| Green chilli | 3 | ₹4,888/q | Jan (₹6,211) | Sep (₹3,440) |
| Coriander (leaves) | 3 | ₹1,102/q | Oct (₹1,741) | Jan (₹701) |
| Papaya | 4 | ₹1,938/q | Sep (₹2,395) | Jul (₹1,647) |
| Tomato | 3 | ₹2,005/q | Dec (₹2,966) | Mar (₹1,382) |
| Brinjal | 3 | ₹2,446/q | Nov (₹3,415) | Mar (₹1,744) |
Buy from India's biggest CEA manufacturing company
Choose your structure and size and get the complete material list, priced this week.
FAQs
What equipment is most important for a Mumbai polyhouse?
For April, prioritise cooling, shading and air movement because the average high reaches 38.4°C and sun reaches 7.1 kWh/m²/day. Before the monsoon, prioritise gutters, funnels, skirting apron, secure film and circulation because July averages 834 mm rain and 90% humidity.
Will fan-and-pad cooling work in Mumbai?
Yes. The climate assessment indicates pads can bring April conditions from 38.4°C to about 32°C inside a fan-and-pad house. Whether it pays depends on your crop, selling period, equipment requirement and operating plan; temperature alone does not establish profitability.
What are the current prices for fan-and-pad equipment?
The listed prices are ₹22,700 per exhaust fan, ₹2,616 per Cellulose Pad (600X150X1800), ₹815 per metre for the 150 mm aluminium pad frame, and ₹8,999 per air-circulation fan, all plus GST. GI and plastic-linked rates are updated every Friday, so check the weekly rate while building the kit.
Can I purchase only a replacement net, fan or fitting?
Yes. Individual fans, pads, nets and fittings are sold for repairs and extensions at the weekly rate. This allows replacement of a damaged component without purchasing a complete material kit.
What warranty and quality documents come with the material?
The GI structure has a 15-year manufacturing warranty, polyfilm has a 2.5-year warranty and shade and insect nets have a 3-year warranty. Every dispatch includes a lab test certificate, and every product has a technical data sheet; QA includes tensile, salt-spray and chemical-analysis checks.
Equipment supply near Mumbai
Nearby towns on the same route, and whether pad cooling works there.
| Town | From Mumbai | Pad cooling | Humid months | Hottest month |
|---|---|---|---|---|
| Equipment supplier in Navi Mumbai | ~20 km | Works (~32°C) | 5 | Apr, 38°C |
| Equipment supplier in Thane | ~20 km | Works (~32°C) | 5 | Apr, 38°C |
| Equipment supplier in Kalyan-Dombivli | ~30 km | Works (~32°C) | 5 | Apr, 38°C |
| Equipment supplier in Mira-Bhayandar | ~30 km | Works (~32°C) | 5 | Apr, 39°C |
| Equipment supplier in Panvel | ~30 km | Works (~32°C) | 5 | Apr, 38°C |
| Equipment supplier in Uran | ~30 km | Works (~32°C) | 5 | Apr, 38°C |






