பாதுகாக்கப்பட்ட சாகுபடிக்கான வழிகாட்டிகள்
பாலிஹவுஸ், நெட் ஹவுஸ், பயிர்கள் மற்றும் பண்ணைத் திட்டமிடல் பற்றிய நடைமுறை ஆலோசனை.
Solar Backup Battery Size for Polyhouse Climate Equipment
A polyhouse battery bank should be sized from the actual essential load in kW, the required emergency hours, battery usable capacity and inverter losses. For fan-and-pad houses, backing up every fan for long cuts can be costly, so define a heat-safe emergency load first.
Pump Selection for Polyhouse Fogger and Cooling Pad Systems
Foggers and cooling pads need different pumps: foggers need the nozzle’s specified pressure, while cooling pads need steady recirculation flow at low to moderate head. This guide shows how to calculate both before buying a pump.
Rain Sensor for Polyhouse Roof Vent: Setup and Control Guide
A rain sensor can command an automated polyhouse roof vent to close as soon as a shower starts, reducing rain entry onto foliage, beds and equipment. The system needs correct sensor placement, limit-switch protection, a rain-priority control rule and regular pre-monsoon testing.
How to Analyse Polyhouse Temperature Humidity Data
Temperature and RH logs show more than whether a polyhouse was hot or humid. Read the timing, duration and relationship between the two values to find crop-risk periods and equipment problems.
Polyhouse Electrical Load Calculation: Connected Load, Cable Size and Power Cost
A polyhouse electrical load calculation starts with every motor and appliance on site, then separates connected load from the equipment that will actually run together. This guide shows how to estimate sanctioned load, feeder current, cable planning and monthly electricity consumption.
How to Choose Solar Power for Polyhouse Fans and Pumps
Solar power can run a large share of daytime polyhouse fan, cooling-pad and irrigation-pump demand, but only after you map the actual loads and their operating hours. This guide helps Indian growers compare grid-tied, hybrid and dedicated solar-pump systems before asking for quotations.
How to Prevent Polyhouse Exhaust Fan Motor Burnout
Exhaust fan motors usually burn out because they run hot for too long, not because they fail without warning. Stable power, correct fan loading, clean airflow paths and a simple inspection routine prevent most repeat failures.
Water Filter for Polyhouse Foggers: Checklist for Foggers and Cooling Pads
Fogger nozzles and cellulose cooling pads need different levels of protection, but both fail quickly when water carries dirt, algae, iron or scale. Use this checklist to test the source water and select sediment, screen, disc and media filters in the right order.
How to Automate a Polyhouse Ventilation System by Temperature
An automatic polyhouse ventilation system reads the crop-zone temperature and opens vents or starts fans when the house becomes too warm. Good automation needs correct sensor placement, suitable actuators, staged set points and fail-safe wiring—not only a thermostat.
How Many Sensors Does a Polyhouse Need? A Practical Sizing Guide
Most small polyhouses need one indoor temperature-RH sensor and one outdoor reference sensor. Larger houses, separate crop zones and fan-and-pad cooling need more sensing points because climate can vary sharply from one end to another.
VPD Management in Polyhouse: A Practical Guide to Temperature and Humidity
VPD management in polyhouse helps growers manage the drying demand on a crop, rather than chasing temperature or humidity alone. It can improve transpiration, irrigation response and disease prevention when used alongside crop observation.
How to Calibrate Temperature and Humidity Sensors in a Polyhouse
A polyhouse controller is only as dependable as the temperature and humidity sensor feeding it. Use a reference comparison, an ice-point temperature check and a saturated-salt RH check to find errors before they affect ventilation, fogging or disease control.
How to Select a Climate Controller for Polyhouse Equipment
A climate controller should match the equipment you have now, protect crops during faults and allow sensible expansion later. Select it by counting real sensors and loads, checking electrical compatibility, and testing its alarm and manual-override provisions.
Polyhouse Temperature Humidity Data Logger Setup for a Climate Audit
A polyhouse climate audit needs more than one temperature reading at noon. Place protected sensors at crop height, log at short intervals and record ventilation, irrigation and weather events alongside the data.
Manual vs Automatic Polyhouse Climate Control Systems
Manual polyhouse control can work well on small, closely supervised farms with a forgiving crop and dependable operators. Automatic control suits fan-and-pad houses, high-value crops and larger areas where timely response and consistent conditions matter more than lower initial investment.
Polyhouse Climate Controller Settings for Fans, Pads and Foggers
Good polyhouse climate controller settings use stages, deadbands and humidity lockouts so fans, pads and foggers do not fight each other. Start with crop targets, then commission each output during real daytime conditions.
How to Reduce Humidity in Polyhouse Without Stressing Crops
High humidity is best reduced gradually by stopping extra moisture at the source, improving air movement, and venting in small stages. This guide gives a crop-safe routine for naturally ventilated and fan-and-pad polyhouses in Indian conditions.
Dehumidifier vs Ventilation for Polyhouse Humidity Control
Ventilation is the first and usually lowest-cost way to remove humidity from an Indian polyhouse, but it works only when outside air contains less moisture than inside air. Mechanical dehumidifiers offer control during rain, cold nights and sealed operation, but their electricity demand and heat output make them a specialist option.
How to Reduce Condensation in a Polyhouse During Winter
Winter condensation is reduced by removing moist air before dawn, keeping crop surfaces warmer and drier, and preventing wet soil or foliage from adding unnecessary moisture. The right routine differs slightly between naturally ventilated and fan-and-pad polyhouses, but the principle is the same: manage humidity before droplets form.
Safe CO2 Levels and Timing for Polyhouse Crops
For most actively growing polyhouse vegetable and flower crops, a working CO2 target of 700–900 ppm is a sensible starting range when the house is closed and receiving adequate light. Enrichment must stop when roof vents, side curtains or exhaust fans are exchanging air, because the added gas is quickly lost and worker safety needs priority.
Where to Place Temperature and Humidity Sensors in a Polyhouse
A temperature and RH sensor should measure the air that the crop experiences, not hot roof air, direct sunshine or fogger spray. Place it near the crop canopy in a shaded, well-mixed representative zone, then add sensors where your polyhouse has known climate differences.
Best Humidity Range for Polyhouse Vegetable Crops
Most fruiting vegetables grow best when relative humidity (RH) stays around 60–75%, with small changes for crop stage and time of day. The key is avoiding long periods above 85% RH, condensation on leaves, and very dry air below about 45–50% RH.
CO2 Enrichment in Polyhouse: When Is It Worth It?
CO2 enrichment is usually worthwhile only in a reasonably sealed, well-controlled polyhouse growing a high-value crop during periods when vents can remain closed. It is rarely a first investment for a naturally ventilated polyhouse, where open vents quickly remove the added CO2.
CO2 Generator vs Cylinder for Polyhouse Enrichment
For most Indian polyhouses, a CO2 cylinder with a regulator, solenoid and controller is the safer and more controllable enrichment source. Fuel-fired CO2 generators can suit a large, tightly managed fan-and-pad house, but their heat, moisture and combustion risks need much stronger controls.
