Polyhouse Temperature Humidity Data Logger Setup for a Climate Audit
Polyhouse Constructions Agronomy Desk · 13 நவ., 2026
A polyhouse temperature humidity data logger helps identify the real cause of heat stress, condensation, poor fruit set or disease-prone humidity. For a useful climate audit, use at least two logger positions in most houses, set a 5–15 minute logging interval, keep sensors at crop-canopy height, and record equipment operation and outdoor conditions for at least 7–14 representative days.
Do not hang a logger on a steel pipe, place it in direct sun, or keep it beside a fogger, cooling pad or exhaust fan. Those locations show a local extreme, not the climate experienced by most plants.
Decide what the audit must answer
Start with one or two practical questions. A clear question determines where to place the logger and what extra observations to take.
Common audit questions include:
- Is the crop too hot between 11 am and 4 pm in summer?
- Does RH remain high overnight and create condensation risk?
- Is the fan-and-pad system cooling the whole house evenly?
- Is one bay warmer or more humid than the rest?
- Does opening the side curtain at a certain time improve the climate?
- Are temperature peaks linked to power cuts, pump failure or delayed ventilation?
- Is the root-zone irrigation schedule raising humidity unnecessarily?
For example, if leaf diseases are increasing near the pad end, logging only at the centre will not answer the question. Put one logger near the crop at the pad end and another at the exhaust end. In a naturally ventilated polyhouse (NVPH), compare the windward and leeward sides instead.
A logger audit measures air conditions. It does not directly measure leaf wetness, soil moisture, nutrient status or pest pressure. Still, a well-kept temperature and RH record gives a strong starting point for investigating those problems.
Choose a logger that is suitable for the house
A basic logger should record temperature and relative humidity (RH), have enough memory for the audit period, and export a time-stamped CSV or spreadsheet file. A screen is useful for checking readings on site, but it is not essential. Remote or Wi-Fi access is convenient, not compulsory.
Select a model with a stated accuracy and operating range suitable for Indian protected cultivation conditions. Many farm audits need a unit able to work reliably in high humidity and summer heat. Check battery life, clock settings and how the sensor is protected from dust and spray.
Useful logger features
Feature | Why it matters in a climate audit | Practical requirement |
|---|---|---|
Temperature and RH measurement | Shows heat load and moisture conditions together | Essential |
Time-stamped records | Lets you link peaks with fan, curtain or irrigation events | Essential |
Adjustable interval | Allows detailed recording without filling memory too soon | Essential |
Downloadable file | Makes daily and weekly comparison easier | Essential |
Replaceable battery or clear battery status | Prevents a lost audit | Strongly recommended |
Sensor accuracy specification | Helps judge whether two logger readings are meaningfully different | Strongly recommended |
Protective radiation shield | Reduces false heating by sunlight and roof radiation | Strongly recommended |
Remote alerts | Useful for continuous management, especially fan-and-pad houses | Optional |
Before deployment, set the clock, date, time zone and interval. Give every logger a simple name such as “Centre canopy”, “Pad end canopy” or “West bay canopy”. This prevents confusion during analysis.
If you are selecting sensors or expanding a controller system, see this guide on how many climate sensors a polyhouse needs. For a short audit, independent loggers are often enough.
Set the right sampling and logging interval
For most vegetable and flower polyhouses, record temperature and RH every 5 to 15 minutes. A 10-minute interval is a good starting point. It catches morning heat build-up, afternoon peaks, fogger cycles and night-time humidity changes without creating an unnecessarily large file.
Use a 5-minute interval when conditions change quickly, such as:
- A fan-and-pad polyhouse with staged fans or foggers
- Summer monitoring during severe heat
- A house with frequent power interruption
- An investigation of uneven cooling or short equipment cycles
Use 15-minute logging for a simple baseline audit in a stable house. Avoid hourly logging for diagnosis. A one-hour average can hide a dangerous 20–30 minute temperature spike during a power cut or after a late curtain-opening decision.
How long should the audit run?
Run the logger for at least 7 days. A 14-day audit is more reliable because it includes different cloud cover, outside humidity and management days. If you are comparing a new shade arrangement, ventilation setting or cooling system adjustment, log for a similar period before and after the change.
Avoid drawing conclusions from a single hot day. Conditions vary with crop stage, outside weather, irrigation timing, wind direction and local electricity supply.
Place sensors where the crop experiences the climate
Sensor position is the most important setup decision. Keep each sensor at approximately the active crop canopy height. For young seedlings this may be 30–60 cm above ground; for an established indeterminate crop it may be around 1.2–1.8 m. Adjust the mounting height as the crop grows.
Place the sensing element in a ventilated radiation shield. A white, purpose-made shield is preferred. It blocks direct solar radiation while allowing surrounding air to pass over the sensor. Without a shield, a logger can read much hotter than the actual air on sunny afternoons.
Keep the logger clear of leaves, stems and trellis wires. Leave enough space around it for air movement. Secure it firmly so it does not swing, touch wet foliage or get knocked during crop work.
Recommended positions by structure type
Structure and audit purpose | Minimum logger positions | Where to install |
|---|---|---|
Small NVPH, general audit | 2 | Centre canopy and one side/bay likely to be warmer or less ventilated |
Long NVPH or multi-span house | 3–4 | Centre, both end zones and a known problem bay; compare windward and leeward areas |
Fan-and-pad house | 3 | Pad-end canopy, middle canopy and exhaust-end canopy |
Nethouse | 2 | Centre canopy and exposed edge or side with stronger afternoon sun/wind |
Nursery bench | 2 | At plant height above a representative bench and at the most exposed bench |
For detailed placement principles, read where to place polyhouse temperature and humidity sensors.
Keep sensors away from these locations
Do not use the following as the main crop-climate measurement point:
- Directly under the roof, ridge or gutter
- Against a GI column, which can heat up or cool down rapidly
- In direct sunlight or in a shadow that stays much cooler than the crop
- Within the direct throw of a fogger or mister
- Immediately beside a cooling pad, exhaust fan, heater or circulation fan
- Right above a wet floor, drain or open water tank
- At a doorway, roll-up curtain opening or leak point, unless that local issue is specifically being investigated
A pad-end or exhaust-end logger is still valuable in a fan-and-pad house. Just keep it far enough from the equipment to measure the crop-zone air rather than the outgoing fan stream or incoming wet pad air.
Record events that explain the graph
The data file alone cannot tell you why RH rose at 7 pm or why temperature increased sharply at 1 pm. Maintain a simple audit sheet on paper or phone. Use the same clock as the logger.
Record the following each day:
- Outside weather: cloud, rain, high wind, unusually hot afternoon or cool night.
- Curtains and vents: opening and closing time, approximate position, roof vent operation if present.
- Cooling and airflow: fan start/stop times, pad pump cycles, fogger cycles and HAF fan operation.
- Irrigation: first and last irrigation time, number of pulses and any drainage or wet-floor issue.
- Shade changes: shade net deployment, removal, or whitewash condition where relevant.
- Crop observations: condensation, leaf wetness, wilting, flower drop, disease patches or edge-row stress.
- Faults: power failure, tripped breaker, blocked pad, torn insect net, pump issue or equipment maintenance.
For fan-and-pad houses, record whether all exhaust fans started as intended and whether the pad was wetted evenly. Cooling performance depends on both airflow and pad condition. The related guides on exhaust fan sizing and matching cooling pad area with exhaust fans can help when data shows a persistent end-to-end temperature difference.
Check the logger before and during the audit
Do a basic cross-check before installation. Keep all loggers together in a shaded, well-ventilated indoor location for 30–60 minutes. Their readings should be reasonably close, within their stated accuracy. If one unit is consistently different, label it and investigate before relying on it.
Do not try to correct readings by guesswork. Review the manufacturer’s calibration guidance, and arrange calibration or replacement when a logger is clearly unreliable. This is especially important for RH sensing because high humidity, dust and chemical spray can affect sensors over time. Use this guide for calibrating temperature and RH sensors in polyhouses.
During the audit:
- Check battery and memory before day one.
- Confirm that each logger has actually started recording.
- Inspect shields after irrigation, stormy weather or crop work.
- Download a test file after the first day, if possible.
- Do not move a logger halfway through the audit without recording the exact date and time.
If a sensor gets wet from direct fogging or spray, note the event. The RH reading may briefly show a local condition rather than the house average.
Read the results as daily patterns, not isolated numbers
Download the file into a spreadsheet. Sort by logger position and create line charts for temperature and RH over time. Compare each zone on the same chart. Also mark curtain, fan, pad-pump and irrigation events if your spreadsheet allows it.
Look first for repeating patterns:
- Fast temperature rise after sunrise: vents or curtains may be opened too late, or the ventilation area may be inadequate.
- Large difference between zones: airflow distribution, curtain operation, shading or cooling may be uneven.
- High RH through the night: night ventilation, irrigation timing, drainage and condensation management need review.
- A temperature peak at fan start: check whether the equipment is staged too late or whether there is a power or control problem.
- RH spikes after irrigation: review pulse timing, drainage and wet surfaces. A short spike may be normal; a long period of high RH needs attention.
- Pad-end cold and humid, exhaust end hot: investigate pad wetting, fan airflow, house sealing and internal air movement.
Crop targets are not one fixed number. Suitable temperature and RH ranges depend on crop, variety, crop stage, solar radiation and season. Use crop symptoms and the daily climate pattern together. For a vegetable-crop reference, see best humidity ranges for polyhouse vegetables.
If you use temperature and RH together for management, calculate or review vapour pressure deficit (VPD) rather than treating RH alone as the final answer. The practical method is explained in using VPD to manage polyhouse climate.
Turn the audit into a small improvement trial
Do not change five things at once. Pick the most important recurring issue, make one sensible adjustment and log again. This shows whether the change helped.
Examples of single changes to test include opening side curtains earlier, improving curtain sealing, adjusting fan stage set points, correcting fogger timing, improving drainage or changing shade management. Check that changes suit the crop and season; maximum cooling is not always the right outcome if it creates excessive RH.
Keep the original file, event sheet and a short summary of each audit. Over one or two seasons, this becomes a practical climate record for your own location and structure.
Next steps
Install the loggers for a 7–14 day baseline audit before making major climate-control changes. Begin with crop-height positions, a 10-minute interval and a daily event sheet. Then compare zones and act on the most consistent problem first.
If the audit points to poor air movement or uneven cooling, inspect the relevant structural and climate-control materials. Polyhouse Constructions supplies protected-cultivation material kits and individual components; you can build a material kit and view this week’s rates or review individual polyhouse materials when planning an upgrade.
Frequently asked questions
How many data loggers are needed for a 1-acre polyhouse?
For a 1-acre house, three to five positions are often more useful than one central logger. Use more positions in long multi-span houses, houses with known hot spots, or fan-and-pad systems where conditions can differ from pad end to exhaust end.
Should a polyhouse data logger be placed above or inside the crop?
Place it at the active canopy height in the air space around the crop, not buried inside dense foliage. As the crop grows, raise the logger so it continues to represent the plant zone.
Can I use a home weather station sensor inside a polyhouse?
It can provide a rough indication if it measures temperature and RH reliably, logs time-stamped data and is placed in a radiation shield. Check its stated accuracy and protect it from direct water, spray and sunlight before using it for management decisions.
What is the best interval for recording temperature and humidity in a polyhouse?
A 10-minute interval is suitable for most audits. Use 5 minutes when investigating fast equipment cycles, power cuts or summer heat spikes, and 15 minutes only for a basic, stable-condition audit.
Do I need to record outdoor temperature as well as indoor temperature?
Yes, an outdoor shaded logger makes the indoor data much easier to interpret. Place it in a ventilated radiation shield away from walls, roofs, concrete heat and direct rain, and do not use a sun-exposed reading as the outdoor reference.
