ਇਹ ਕਿਵੇਂ ਕੰਮ ਕਰਦਾ ਹੈਵੱਖਰੀ ਸਮੱਗਰੀ ਖਰੀਦੋ

When to Replace Cellulose Cooling Pads in a Fan-and-Pad Polyhouse

Polyhouse Constructions Agronomy Desk · 13 ਨਵੰ 2026

A cellulose cooling pad does not need replacement simply because it looks old or stained. Replace it when it can no longer wet evenly, allow air through freely or cool incoming air effectively after proper cleaning and system checks. The clearest signs are persistent dry strips, crushed or collapsed flutes, heavy scale within the pad, physical breakdown, and reduced cooling despite adequate water flow and correctly working exhaust fans.

For most fan-and-pad polyhouses, assess pads before the main hot season. In much of India, that means January to March, before the severe summer load begins. A well-maintained pad may serve for several seasons, while hard water, dust, algae, poor filtration and long daily operation can shorten its useful life considerably.

Start with a practical replacement decision

Do not judge the pad alone. Poor cooling can also result from an undersized pump, blocked filters, wrong water distribution, leaking gutters, fan faults, open doors, damaged shutters or inadequate pad area. First make sure the complete fan-and-pad system is operating as designed.

A pad should move from “maintain” to “replace” when one or more critical faults remain after cleaning and basic repairs. In particular, plan replacement if:

  • More than a few small areas remain dry after the pump has run long enough to wet the full face.
  • Flutes are crushed, soft, delaminating or visibly closing, restricting air passage.
  • Scale remains deep inside the flute channels and water does not spread through the pad.
  • The pad face has holes, torn sections, sagging panels or gaps around the frame that let hot air bypass it.
  • Cooling performance is consistently poor even after confirming water flow, pump condition, filters, fan capacity and shutters.
  • The pad develops recurrent algae, odour or microbial slime that returns quickly despite cleaning and water-management corrections.

One damaged panel can often be changed individually. If damage, scaling or flute collapse is widespread across the pad wall, replacing the affected run is usually more sensible than patching repeatedly.

Five measurable signs that cellulose pads need replacement

1. Uneven wetting that does not improve

When the pump starts, water should spread down the pad face in a reasonably uniform sheet. A few minutes after start-up, inspect both the top and lower portions. The colour of a wet cellulose pad is generally more uniform and darker than a dry one.

Dry vertical bands, pale areas or dry lower corners indicate that some part of the system is not wetting correctly. First inspect the distribution pipe, holes, header level, pad supports, pump, filter and recirculation flow. Also check whether dust or scale has blocked the flute openings.

Replace the panel if dry zones persist after these corrections and cleaning. A dry section passes hot outside air with almost no evaporative cooling. It also makes the crop near that side of the house more vulnerable during April–June heat.

2. Collapsed, crushed or blocked flutes

The flute channels are the air passages inside the cellulose media. They must remain open so exhaust fans can pull outdoor air through the wetted surface. Look from the side edge of the pad and compare it with an intact area.

Replacement is justified when you see:

  • Flattened channels over a substantial area
  • Soft, compressed pad edges
  • Layers separating from each other
  • Bent or distorted panels that no longer fit tightly in the frame
  • Sections that stay clogged with mineral deposits after cleaning

A pad can still appear wet from the front while blocked flutes restrict airflow. This increases resistance on the fan system. Air may then enter through leaks, doors and other easier openings rather than through the cooling pad.

3. Reduced cooling across the house

Measure temperature rather than relying only on how the house feels. On a hot afternoon, take readings at the pad inlet and near the fan end, at crop-canopy height. Use the same reliable thermometer or calibrated sensor, keep it shaded from direct sun, and note outside temperature and relative humidity at the same time.

Some temperature increase from the pad end to the fan end is normal because air absorbs heat as it travels through the crop and structure. But if the air immediately inside the wet pad is barely cooler than outside air, the pad system deserves attention.

Cooling potential depends heavily on outside humidity. In hot, dry conditions, evaporative pads can provide a clearly noticeable reduction; during humid monsoon periods, even a new pad has limited evaporative cooling potential. Compare readings on similar hot, dry days. If the measured cooling has fallen over time, and pump, water distribution and fans all pass inspection, the pad media may have reached end of life.

Use a simple log for at least several operating days. It is more useful than taking one reading during a cloudy or humid spell.

What you observe

Likely cause to check first

Replace the pad?

Narrow dry strip below one header section

Blocked distribution hole, unlevel header or local dirt

Usually no; repair and clean first

Whole pad face remains partly dry

Low flow, clogged filter, pump fault or blocked media

Only if media stays blocked after correction

Good wetting but weak air movement at fan end

Fan, shutter, belt/motor, leak or pad-area mismatch

Not until airflow system is checked

Wet pad, but air enters through holes or gaps

Torn panel, failed seal or poor frame fit

Replace damaged panel or reseal

Deep scale plus poor wetting and low cooling

Hard-water deposits inside flutes

Usually yes if cleaning cannot reopen channels

Soft, sagging, crushed or delaminated pad

Age, water damage or physical damage

Yes

4. Mineral scale that is inside the pad, not only on it

White or brown deposits on the surface may be manageable if found early. The more serious problem is scale lodged inside the channels. It prevents water from spreading across the cellulose and reduces effective wet surface area.

Inspect the side edge and several locations across the pad wall. If deposits are thick, hard and extend through the media, simple surface washing will not restore the pad fully. Do not use aggressive cleaning methods that tear the cellulose or crush the flute structure.

Hard borewell water is a common reason for early pad failure in many Indian growing areas. Test source water periodically and pay attention to hardness, dissolved salts and iron where relevant. Improve filtration and bleed-off practices before fitting new pads. Otherwise, the replacement pads can develop the same problem quickly. Read the guide on water filtration for foggers and cooling pads while planning the correction.

5. Repeated biological growth, odour or fibre breakdown

Algae and slime reduce water distribution and can trap dust. Green growth on the face does not always mean the pad must be discarded. Clean it carefully, correct light exposure at the sump where practical, remove debris and maintain the water system.

However, replacement becomes the better option where growth is recurrent and accompanied by soft fibres, a musty smell, deep staining, degraded bonding or blocked channels. A pad that sheds fibres or loses its structural shape will not regain reliable performance.

For a cleaning sequence that protects the pad media, see how to clean algae and scale from cooling pads. Follow equipment instructions and take local agronomist advice for water hygiene. Do not apply unapproved chemical treatments to a crop-house cooling system.

Check the system before you blame the pad

A replacement pad will not solve a design or maintenance fault elsewhere. Carry out this short check on a warm day before ordering material.

  1. Clean the sump and filters. Remove sediment, leaf matter and sludge. Check that the water level remains adequate while the pump runs.
  2. Inspect the pump and pipework. Confirm steady delivery to the full length of the header. Look for leaks, blocked holes and an unlevel distribution pipe.
  3. Watch wetting for 10–15 minutes. Look at the entire face, including joins, corners and lower edges. Mark dry bands with washable chalk or note their positions.
  4. Check pad frames and seals. Air must be pulled through the media, not around it. Close gaps at the sides, top and bottom.
  5. Check fans and shutters. Fans should reach normal speed, rotate in the correct direction and open shutters fully. Dirty guards and shutters also reduce airflow.
  6. Compare temperatures and humidity. Record outside conditions, pad-side temperature and fan-side temperature at crop height. Repeat on comparable days.
  7. Review pad-to-fan matching. If fans were added, changed or are running below expected capacity, the existing pad wall may not suit the airflow. Use the guidance on matching cooling pad area with exhaust fans.

If these checks solve the issue, continue with maintenance. If the media remains physically damaged or functionally blocked, replacement is justified.

How long do cellulose cooling pads usually last?

There is no fixed replacement year for every farm. In well-managed systems using reasonably clean water, pads often work for roughly 3–5 years. With hard water, frequent dust, poor filtration, continuous high-temperature operation or neglected cleaning, useful life can be closer to 2–3 years. Some pads may last longer, but age alone should not overrule condition and performance checks.

The operating environment matters:

  • Dry, dusty summer areas: Dust can coat the face and encourage uneven wetting.
  • Hard-water locations: Mineral scaling is often the main life-limiting factor.
  • Humid coastal or monsoon climates: Biological growth and low evaporative potential need closer attention.
  • High-value crops: Even moderate cooling loss can affect flower quality, fruit set, crop duration and worker comfort. Replace earlier if the climate data shows the pad is limiting production.

Keep a record of installation month, water source, cleaning dates, filter condition, temperature observations and replaced panels. This gives a much better replacement forecast than a calendar reminder alone.

Replace only the panel or the complete pad wall?

Replacing a single panel makes sense when the fault is local: accidental damage, a tear, one collapsed section near a door, or a panel affected by a distribution leak. Match the replacement thickness, flute direction, panel height and framing arrangement to the installed system. A mismatched panel can create bypass gaps or an uneven resistance pattern.

Consider changing the whole run or wall when most panels show scale, brittle edges, poor wetting or loss of cooling. Mixing heavily aged pads with new pads can lead to uneven water use and airflow. The new panel may take more air while old blocked panels contribute little.

If you are unsure of pad thickness or configuration, first review how to choose cellulose cooling pad thickness for polyhouses. Also inspect the pad support, gutter and header before installation. New media cannot compensate for a corroded frame, an undersized recirculation arrangement or leaks.

Plan replacement without exposing crops to heat

Avoid waiting until peak May heat to discover that the pad wall has failed. Order and fit replacement media before the main summer crop period, allowing time for a wet-run test.

Use this replacement checklist:

  • Measure each panel height, width and thickness accurately.
  • Photograph the frame, header, gutter, supports and pad joints before removal.
  • Confirm flute orientation and water-flow direction for the chosen media.
  • Service filters, sump, pump, distribution header and return gutter first.
  • Clean the frame and remove old seal material that creates bypass gaps.
  • Fit panels firmly but without crushing edges.
  • Run water and inspect full-face wetting before switching on exhaust fans.
  • Run fans next and check for air leaks and unusual vibration.
  • Record pad-side and fan-side climate readings during the first hot-day test.

For replacement cellulose pad media and other fan-and-pad components, you can buy individual items or use the kit builder with live weekly rates to review quantities and specifications. If the whole system has recurring cooling issues, it may also help to revisit what a fan-and-pad polyhouse requires in terms of controlled airflow and wet-pad operation.

Next steps

Inspect the pad wall before summer and document dry areas, physical deformation and temperature readings. Repair water distribution, filtration, seals and fan faults first. Replace cellulose media when uneven wetting, blocked or collapsed flutes, internal scale or lost cooling performance remain after those checks.

After replacement, make monthly inspections during the hot season and maintain a simple water-and-climate log. That routine protects the new pads and gives you early warning before crop stress becomes visible.

Frequently asked questions

Can I use a cellulose cooling pad if one section is dry?

A small temporary dry patch may be manageable while you repair a blocked header hole or correct water flow. Do not run through peak heat with a persistent dry section, because it admits hot air and causes uneven conditions near the pad wall.

Do brown stains mean that a cooling pad must be replaced?

Not always. Surface staining from dust or water minerals can often be cleaned, but deep deposits within the flute channels are more serious. Judge the pad by wetting, airflow and cooling performance, not colour alone.

Why is my polyhouse still hot even though the cooling pads are wet?

Wet pads alone do not guarantee cooling. Check exhaust fan capacity and operation, shutters, air leaks, pad area, outdoor humidity and whether the pad flutes are blocked. In humid weather, evaporative cooling will naturally be limited.

Can individual cellulose pad panels be replaced?

Yes, a single panel can be replaced when damage is local. Match its thickness, dimensions and flute orientation with the existing pad wall, and seal it properly so air cannot bypass the media.

Should cooling pads be changed before every summer?

No, replacement every year is not normally necessary if pads remain structurally sound and perform well. Inspect them before summer, clean and service the water system, then replace only media that cannot be restored to even wetting and acceptable airflow.

ਆਪਣੀ ਕਿੱਟ ਬਣਾਓ