Cellulose Cooling Pad Maintenance Schedule for Indian Farms
Polyhouse Constructions Agronomy Desk · 13 ਨਵੰ 2026
A working fan-and-pad system depends on clean, evenly wetted cellulose pads. For most Indian farms, the practical routine is: inspect water flow every day in the hot season, flush the sump and lines weekly, clean and dry the system before long idle periods, and protect the pads from rain splash, dust and rodents. The exact frequency depends mainly on water quality, crop dust, summer operating hours and whether the house runs through monsoon.
Do not wait for a pad to turn dark, smell stale or develop dry strips. By then, cooling and airflow may already be poor. This cellulose cooling pad maintenance schedule is meant for fan-and-pad polyhouses and can be adapted for small or large houses.
What good pad maintenance achieves
Cellulose pads cool incoming air by evaporation. Water should spread from the top distribution pipe, wet the pad face evenly, pass through the pad sheets, and return to the sump. Exhaust fans then pull this cooled air across the crop.
Scale, algae, dust and biofilm interfere with this process. They close the air passages, make some areas too wet and others dry, and increase resistance to airflow. The result can be a hotter fan end, uneven crop growth, higher pump running time and wet patches that encourage disease around the pad wall.
A good routine helps you maintain:
- Uniform wetting from top to bottom and across the full pad length.
- Free return of water to the gutter and sump.
- Sufficient airflow through the pad when fans are running.
- Cleaner water with less suspended dirt and organic matter.
- Pads that remain structurally firm, without crushed corners or separated layers.
Pad maintenance is only one part of cooling performance. Check that pad area suits the fans, since incorrect matching cannot be fixed by cleaning alone. See how to match cooling pad area with exhaust fans.
The daily, weekly and monthly checklist
Use this as the core routine while the system is operating in warm weather. Record observations in a notebook or on the climate controller log. A pattern, such as one section repeatedly drying first, is more useful than a single reading.
Frequency | What to check or do | What a problem looks like | Immediate action |
|---|---|---|---|
Every operating day | Run pump and inspect pad face, top pipe, gutter and sump water | Dry vertical strips, overflowing gutter, leaks, foam or bad smell | Clear obvious blockage; correct water level; investigate unequal flow before peak heat |
Every 2–3 days in dusty or very hot weather | Clean screen/filter and remove leaves or debris from sump | Slow return flow, dirty water, blocked filter | Rinse filter and remove debris; refill with clean water if needed |
Weekly | Flush sump, return gutter and distribution line with clean water | Sediment, slime, visible deposits, uneven wetting | Drain, rinse, refill and test the system |
Monthly during use | Inspect pad structure, supports, seals, pump and connections | Soft edges, sagging, crushed flutes, leaks or vibration | Repair support or leaks; plan deeper cleaning or replacement if damage is widespread |
Before and after long shutdown | Drain, rinse, dry fully and inspect | Damp smell, algae growth, rodent damage | Clean, dry and keep the pad bay protected before restarting |
Never put hands near rotating fan blades, exposed electrical connections or a running pump. Isolate electrical power before opening a pump filter, working on wiring or carrying out repairs.
Summer routine: March to June in most plains
Summer is the highest-risk period because pads may operate for many hours each day. In dry-hot areas, high evaporation can concentrate dissolved salts in recirculating water. In dusty belts, airborne soil and crop debris load the pad surface and sump faster. Coastal and humid regions may have fewer operating hours but can still develop algae if water remains stagnant.
Before the summer cooling season
Complete this commissioning check one to two weeks before regular use:
- Inspect the dry pads. Look for brittle areas, sagging, gaps between sections, damaged bottom edges and insect or rodent damage. Ensure pads sit straight in their frames and are supported evenly.
- Clean the sump and gutters. Drain old water. Remove leaves, plastic pieces, sand and sediment. Rinse the tank, gutter and return path.
- Check the filter. Clean the screen or filter housing and inspect its seal. A filter that is bypassed or torn sends debris directly to the distribution pipe.
- Check the water distribution line. Open or remove accessible end caps as designed, flush the line, then inspect holes or outlets for uniform discharge. Do not enlarge holes with sharp tools; this can permanently upset water distribution.
- Test pump, float valve and drainage. Confirm that the pump starts correctly, water returns freely and the sump does not overflow. Check for leakage at joints.
- Run a wetting test. Operate the pump without depending on crop cooling. The pad should become evenly wet within a short period. A few minutes may be enough for initial wetting, but timing varies with pad height, thickness and distribution design.
- Check fan direction and shutters. The fan should pull air from the pad side towards the exhaust side. Poor fan performance can make a clean pad appear faulty. Refer to exhaust fan sizing for fan-and-pad polyhouses if airflow has never been verified.
During the summer operating day
At start-up, watch the full pad face, not just the first section. A dry strip means the incoming air there is not being cooled properly. Common causes are a blocked outlet, a tilted distribution pipe, insufficient water flow, a clogged filter or a pad section that has shifted.
Keep the sump at its intended working level. Very low level can cause pump cavitation and irregular wetting. Overfilling can lead to overflow and permanent wetness around the structure. Repair leaks promptly; continual water on the floor attracts algae and can create a slipping hazard.
Use clean water suitable for irrigation where possible. Hard water, high bicarbonates and high dissolved salts can cause scale more quickly. There is no universal flushing interval based only on days: farms with hard borewell water may need more frequent partial drain-and-refill than farms using lower-mineral water. If you see white or grey deposits, reduced wetting, or rough, hard pad surfaces, review water quality and flushing frequency.
Monsoon routine: prevent dirt, dilution and long wet periods
Monsoon conditions change the job. Ambient air is already humid, so evaporative cooling gives less temperature reduction than in dry heat. Running pads unnecessarily can lift humidity further and keep crop surfaces damp. Use temperature and relative humidity readings, crop condition and ventilation need to decide when to operate.
Rain can also carry dust, roof runoff or splash into the pad bay if drainage and external protection are poor. Check after heavy rain.
Monsoon checklist
- Keep roof runoff directed away from the pad wall and sump. Do not allow soil-laden runoff to enter the recirculation water.
- Inspect side sealing, pad-frame gaps and gutter alignment after storms or strong winds.
- Remove leaves, insect bodies and wind-blown debris from filters and gutters more often.
- Do not leave the pads wet overnight merely because the pump was used in the afternoon. When cooling demand has ended, allow adequate fan ventilation so the pad face can dry.
- Check for algae, slimy surfaces and musty odour at least weekly. These are signs that the water system is holding organic contamination.
- Drain and clean promptly if floodwater, muddy water or substantial debris enters the sump.
Avoid aggressive brushing, high-pressure jets or strong chemicals on cellulose pads. The paper flutes can crush or delaminate. For algae and mineral deposits, first identify whether the main cause is light exposure, stagnant water, filtration failure or hard water. This detailed guide explains safe diagnosis and cleaning methods: how to clean algae and scale from cooling pads. If a cleaning agent is required, use only a compatible product and method approved by the pad supplier, follow its label, and seek advice from your KVK or protected-cultivation agronomist.
Winter and cool-season routine: dry storage matters
In many parts of India, fan-and-pad cooling is used rarely from roughly November to February. The exact months vary greatly: warm coastal areas and protected houses with high solar load may still need occasional operation, while north Indian farms may have a long inactive period.
Long-standing water is the main avoidable problem in this season. It can grow algae, accumulate debris and leave mineral deposits as it evaporates. When no cooling is expected for several days, do not keep the system full simply for convenience.
Shutdown checklist
- Stop the pump and allow the pad to drain completely into the gutter and sump.
- Drain the sump, flush out sediment and rinse the return channel and accessible distribution line.
- Run fans or maintain ventilation until the pad is dry to the touch throughout. Do not cover or pack a damp pad.
- Inspect both pad faces and the lower edge. Note any thin, weak, crushed or persistently discoloured sections.
- Protect the pad bay from direct rain, drifting dust, rodents and birds while retaining airflow. Do not wrap the pad tightly in non-breathable plastic, as trapped moisture encourages mould.
- Isolate the pump electrical supply if it will not be used, according to your electrician’s and equipment supplier’s guidance.
A dry, clean pad starts more reliably next summer and is less likely to develop odour in the first week of operation.
Water management rules that protect the pads
Many pad failures start in the water circuit rather than in the cellulose itself. Build these practices into the schedule.
Filter before water reaches the pad
Fit and maintain a suitable filtration arrangement for the water source and recirculation loop. Check it frequently during use. A clean filter protects distribution outlets; it does not remove dissolved salts, so hard-water scale may still need a planned drain-and-refill routine.
Manage the sump, not only the pad face
The sump collects dust, leaf fragments, salts and biological growth. Removing floating debris daily is quick. A complete weekly flush is usually a sensible starting point in peak summer, then tighten or relax the interval based on water clarity, sediment and mineral deposits.
Do not use fertiliser solution, irrigation return water or pesticide-contaminated water in the pad system. These can damage equipment, leave deposits and create worker-safety concerns. Keep pad water plumbing separate from fertigation as far as practical.
Look for even wetting and controlled drainage
Too little water causes dry zones. Too much water can cause overflow, excessive wetting and poor hygiene around the wall. The correct pump flow, gutter slope and distribution pipe layout depend on pad dimensions and system design. If you are replacing pads or changing thickness, confirm that the current pump and water distribution still suit them. Read how to choose cellulose cooling pad thickness before changing the pad specification.
Inspection guide: clean, repair or replace?
Not every stain means a pad needs replacement. Decide after the system is cleaned, flushed and tested.
Pad condition | Likely response |
|---|---|
Light dust or loose debris; pad remains firm and wets evenly | Clean filter, flush water circuit and gently remove accessible loose debris |
Uneven wetting but pad structure is sound | Check pump output, filter, distribution pipe level, outlet blockage and gutter return |
Mineral scale or algae recurring soon after cleaning | Improve water-management interval, investigate source water and use only pad-compatible treatment methods |
Bent lower edge, local crushing or gaps between pad sections | Correct frame/support issue; replace affected section if airflow path cannot be restored |
Soft, broken, delaminated or severely blocked sheets | Replace the damaged pad section; cleaning will not restore its structure |
Replacement timing varies widely. It depends on pad quality, water chemistry, UV and dust exposure, maintenance discipline and annual run hours. Do not set a replacement date based only on age. Use physical condition and cooling uniformity as the decision points. For the full replacement signs, see when to replace cellulose cooling pads.
A simple maintenance record for the farm team
Assign one person for daily observation and one person for weekly flushing. This avoids the common problem where everyone assumes another worker has cleaned the sump.
Keep a sheet with these columns:
- Date and weather condition.
- Pump operating hours.
- Water source and whether fresh water was added.
- Filter cleaned: yes or no.
- Sump flushed: yes or no.
- Pad wetting: even, minor dry strip, or major dry zone.
- Water appearance and any odour.
- Leakage, overflow, algae, scale or physical damage observed.
- Corrective work completed and person responsible.
If the house has temperature and humidity sensors, compare pad-end and fan-end conditions during hot afternoons. A worsening temperature difference, alongside dry strips or a dirty pad, indicates that the cooling system needs attention. Do not judge performance only at one point near the crop.
Next steps
Print the daily and weekly checklist, train the operator to recognise dry strips and dirty sump water, and complete a full drain-and-dry procedure before any long idle period. If pads remain uneven after basic cleaning, inspect the filter, pump, distribution line and fan performance before purchasing replacements.
For replacement pad material or other fan-and-pad components, you can buy individual protected-cultivation items or use the kit builder with live weekly rates to review quantities and specifications.
Frequently asked questions
How often should I flush a cellulose cooling pad sump?
During regular summer operation, flushing the sump and accessible water circuit weekly is a practical starting point. Flush more often if the water is hard, dusty, visibly dirty, or if algae and sediment build up quickly.
Can I leave cooling pads wet at night?
Avoid leaving pads wet for long periods when cooling is no longer needed. Drain the system and allow ventilation to dry the pad face, especially in monsoon or cool weather when humidity is already high.
Why is one part of my cooling pad dry while the rest is wet?
A dry strip usually points to a blocked distribution outlet, dirty filter, uneven top pipe, low pump flow or a shifted pad section. Check these causes before assuming the cellulose pad itself has failed.
Can borewell water damage cellulose cooling pads?
Hard borewell water can leave mineral scale as water evaporates, reducing airflow and wetting over time. Regular drain-and-refill, filtration for particles and water-quality assessment help control the problem.
Should I pressure wash cellulose cooling pads?
No. High-pressure washing can crush the cellulose flutes and weaken the pad structure. Use gentle, pad-compatible cleaning methods and follow the pad supplier’s instructions for any approved cleaning agent.
