આ કેવી રીતે કામ કરે છેઅલગ સામગ્રી ખરીદો

How to Size Fogger Nozzles for a Polyhouse Correctly

Polyhouse Constructions Agronomy Desk · 13 નવે, 2026

Fogger sizing is not only about choosing a nozzle hole diameter. A correct polyhouse fogger nozzle size calculation combines four things: nozzle output in litres per hour (LPH), nozzle and line spacing, pressure at the nozzle, and short on-off run cycles.

First lay out the nozzles for uniform coverage. Then add the flow of every nozzle that will run at the same time. Finally, select a pump that can supply that flow at the nozzle maker’s required working pressure, with some margin for filter loss and pipe friction. Test the system in the hottest part of the day before fixing controller settings.

Start with the result you want from fogging

Foggers add very small water droplets to the air. When droplets evaporate before reaching leaves or the floor, they can reduce air temperature slightly and raise relative humidity (RH). They are useful in dry, hot periods, nursery areas, propagation zones and some flower crops.

They are not a substitute for ventilation. In a naturally ventilated polyhouse, outside air movement can carry fog out quickly. In a fan-and-pad house, fogging needs careful coordination with fans, pads and RH control. Running all systems without a control plan can create excess humidity, wet foliage and disease pressure.

Set the purpose before choosing nozzle output:

Primary purpose

What the system should do

Main sizing priority

Humidity support in a dry crop canopy

Raise RH gradually without leaf wetness

Fine droplets, short pulses, good sensor feedback

Nursery or propagation

Maintain more stable humidity around young plants

Closer spacing, zoning and very uniform distribution

Supplementary summer cooling

Use evaporation to reduce heat load where air is dry

Adequate evaporation, airflow and water quality

Dust suppression or coarse wetting

Put visible water onto surfaces

This is not fogging; use a different system if needed

For vegetables such as capsicum, cucumber and tomato, RH management must also consider fungal and bacterial disease risk. A humid crop canopy is not automatically a healthy crop canopy. Check crop-specific recommendations from your agronomist or KVK, especially during the monsoon and cool winter mornings.

For a broader distinction between droplet systems, read fogger vs mister for polyhouse cooling and humidity.

Know the nozzle flow at its working pressure

Nozzle orifice size alone does not tell you the water use. A nozzle rated at 5 LPH at one pressure will give a different flow at another pressure. Pressure also changes droplet size and spray pattern.

Always obtain these details from the nozzle supplier:

  • Rated discharge, usually in LPH, at a stated pressure
  • Recommended operating-pressure range
  • Spray angle and expected droplet quality
  • Minimum filtration requirement
  • Nozzle material and whether it has an anti-drip feature

A useful hydraulic rule is:

New flow = rated flow × √(actual pressure ÷ rated pressure)

For example, assume a nozzle is rated at 6 LPH at 4 bar. If pressure at the nozzle is only 3 bar:

Flow = 6 × √(3 ÷ 4) = about 5.2 LPH

The flow may not fall dramatically, but the spray can become less fine and less uniform. The far end of a long lateral may therefore produce bigger droplets even though the first nozzles look satisfactory.

Measure the actual discharge on your farm

The nozzle chart is a starting point. Confirm it after installation.

  1. Fit a pressure gauge near the pump outlet and another near the far end of a representative fogger line, if possible.
  2. Run the system at normal working pressure.
  3. Collect water from three nozzles: near, middle and far end. Use identical containers and collect for one minute.
  4. Measure collected water in millilitres. Since 1,000 ml equals 1 litre, multiply the one-minute amount by 60 to get LPH.
  5. Compare the three outputs. A large difference indicates pressure loss, clogging, unsuitable line diameter or a regulator problem.

Do not judge only by looking at the mist. A nozzle can appear to spray while delivering too little water or producing droplets that settle on plants.

Set nozzle and fogger-line spacing before counting nozzles

Spacing decides uniformity. Nozzle flow decides how much water enters that uniform pattern. If the spacing is too wide, increasing pump size will not fix dry strips between lines.

For many polyhouse fogging layouts, nozzle spacing is commonly planned in the range of about 2.5 to 4 m along a line. Fogger lines are often around 3 to 5 m apart. The right distance depends on nozzle spray angle, mounting height, pressure, crop height, ventilation rate and whether the system is for a nursery or a mature crop.

Use the tighter end of the range when:

  • The roof is high or there are strong air currents.
  • You are maintaining a sensitive nursery zone.
  • The crop canopy is dense and tall.
  • The nozzle pattern has limited overlap.

Use wider spacing only after a practical uniformity test shows that there are no dry areas. A layout drawing is useful, but a day-time test is essential. For detailed layout planning, see how far apart fogger lines should be in polyhouses.

Position nozzles for evaporation, not crop wetness

Install foggers high enough for the droplets to mix with air before reaching leaves. Avoid directing spray onto roof film, trusses, electrical fittings, fans or the crop row. Keep the layout symmetrical from one sidewall to the other.

In a multi-span structure, each span should receive comparable coverage. Keep a separate zone for a small nursery or hardening area where its humidity requirement differs from the main crop.

Calculate nozzle count and total water flow

Use the planned grid to calculate the number of nozzles. Do not size from polyhouse area alone; a 1,000 m² house can have different dimensions and therefore different line lengths and nozzle counts.

Core formulas

Number of lines = polyhouse width ÷ selected line spacing

Round the result to a practical whole-number layout, keeping outer lines equally spaced from sidewalls.

Nozzles per line = line length ÷ nozzle spacing

Again, round to a balanced layout. Place the first and last nozzle at similar distances from the end walls.

Total nozzles = number of lines × nozzles per line

Total flow (LPH) = total nozzles operating together × actual nozzle discharge (LPH)

If you run zones separately, calculate the pump for the largest zone that operates at one time, not for every nozzle in the whole polyhouse.

Worked example: 24 m × 40 m polyhouse

Assume a 960 m² polyhouse needs humidity support. The selected layout is 4 m between lines and 3 m between nozzles. The selected nozzle delivers 6 LPH at its required operating pressure.

Item

Calculation

Result

Polyhouse width

—

24 m

Line spacing

—

4 m

Number of lines

24 ÷ 4

6 lines

Polyhouse length

—

40 m

Nozzle spacing

—

3 m

Nozzles per line

Practical balanced layout

14 nozzles

Total nozzles

6 × 14

84 nozzles

Nozzle discharge

—

6 LPH

Total operating flow

84 × 6

504 LPH

So, if all 84 nozzles run together, the pump must supply at least 504 LPH at the required pressure at the farthest nozzle. This is only the nozzle flow. It is not yet the final pump selection.

Select pump pressure and flow with a safety margin

A pump’s flow rating at zero or low pressure is not useful for fogger selection. Read the pump curve and confirm its delivery at the actual pressure needed by the nozzles.

Allow approximately 20% to 30% flow margin for sensible design flexibility, filtration losses, fittings, pressure regulation and modest future variation. In the worked example:

Required pump flow = 504 LPH × 1.2 to 1.3 = about 605 to 655 LPH

Choose a pump that can provide this flow at the required system pressure, after allowing for friction loss in the main line, laterals, elbows, valves, filters and elevation difference. Do not simply buy a higher-HP pump. Excess pressure can increase discharge, alter the spray pattern and cause leaks or pipe failures.

Use these components in a practical system:

  • Correctly sized water filter, followed by finer filtration as specified for the nozzle
  • Pressure gauge near the pump and preferably at the far end
  • Pressure regulator or bypass arrangement
  • Flush valves or removable end caps on laterals
  • Zone valves where different sections need separate operation
  • Non-return valve where needed to avoid line drain-back

Poor filtration is one of the main reasons a correctly designed system gives uneven fog. Water with silt, algae, iron deposits or hardness-related scale needs appropriate treatment and maintenance. Review water filtration needed for foggers and cooling pads before finalising the system.

Pump sizing is also affected if the same pump serves foggers and cooling pads. These systems have very different pressure and flow requirements, so separate pumps or properly designed separate circuits are often easier to control. See pump selection for polyhouse foggers and cooling pads.

Calculate run time from nozzle flow, then fine-tune with RH

Once total operating flow is known, calculate water applied per cycle:

Water per cycle (L) = total operating flow (LPH) × run time in seconds ÷ 3,600

Using the 504 LPH example:

  • For a 30-second cycle: 504 × 30 ÷ 3,600 = 4.2 litres
  • Spread across 960 m²: 4.2 ÷ 960 = about 4.4 ml/m² per cycle

This is why foggers should normally run in short pulses. A continuous long run can quickly overshoot the RH target, especially after clouds arrive, ventilation reduces or the crop canopy becomes dense.

A practical starting approach is to use short pulses such as 15 to 60 seconds, followed by an off period of a few minutes. The correct interval varies widely with outside temperature, RH, wind, vent position, crop stage and nozzle type. There is no universal “minutes per hour” setting.

Use sensors at crop height

Place a calibrated temperature-RH sensor at representative crop height, away from direct fog, drippers, walls and fan discharge. Watch both indoor and outdoor conditions. If RH rises sharply but temperature barely changes, reduce pulse length or increase the off interval.

Stop or restrict fogging when:

  • Leaves remain visibly wet.
  • Condensation appears on the roof or crop.
  • RH remains high after fogging stops.
  • Evening approaches and there is insufficient time to dry the canopy.
  • A disease-prone crop is already under humid conditions.

For controller logic, read climate controller set points for fans, pads and foggers. Sensor position matters as much as the set point; use the guidance on where to place temperature and humidity sensors in a polyhouse.

Commissioning checklist for even fogging

Before relying on the system for a crop, complete this checklist during a warm, dry afternoon:

If one side of the house is always drier, first inspect pressure, blocked nozzles, line length and ventilation imbalance. Do not immediately increase the nozzle size everywhere.

Next steps

Prepare a scaled drawing of your polyhouse showing spans, bays, crop rows, fogger lines and proposed nozzle points. Get the nozzle’s pressure-flow chart, calculate the largest simultaneous zone flow, and select filtration and a pump based on the pressure required at the far end.

For the structure, polyfilm, nets and fittings around the fogging layout, you can build a material kit with live weekly rates. Polyhouse Constructions supplies protected-cultivation material kits and individual items; use the product data sheet to match fittings and materials to your design.

Frequently asked questions

What nozzle size is best for a polyhouse fogger?

There is no one best orifice size for every polyhouse. Choose a nozzle based on its tested LPH, droplet pattern and required pressure, then match it to your spacing, crop and ventilation conditions.

How many fogger nozzles are needed per 1,000 m² polyhouse?

The count depends on the house dimensions and the selected line and nozzle spacing, not only on area. A narrower, longer house may need a different nozzle count than a wider house of the same area.

Can I use a normal irrigation pump for fogger nozzles?

Only if its pump curve delivers the required flow at the nozzle system’s working pressure. Many irrigation pumps provide high flow at low pressure, while fine fogging may need a different pressure range.

Why do nozzles at the end of my fogger line give less fog?

Common causes are pressure loss in undersized or long laterals, clogged filters, partly blocked nozzles and unsuitable pressure regulation. Compare catch-test output and pressure at the first and last nozzle before changing the layout.

Should foggers run at night in a polyhouse?

Usually avoid routine night fogging unless a crop-specific requirement and sensor readings justify it. Night ventilation and evaporation are lower, so fogging can leave leaf wetness and high RH for too long.

તમારી કિટ બનાવો