Summer Shade Net Percentage for Polyhouse Crops: How to Choose
Polyhouse Constructions Agronomy Desk · 13 నవం, 2026
In an Indian summer, the best shade net percentage for polyhouse summer is usually 30–40% for fruiting vegetables in a naturally ventilated polyhouse and 20–30% where fan-and-pad cooling is working well. Leafy crops, young seedlings and some flowers may need 40–60%, while deeply shade-loving ornamentals can need more.
Do not choose only by the outside temperature. A shade net reduces light as well as heat load. Too little shade causes leaf scorch, flower drop and high crop temperature. Too much shade reduces photosynthesis, delays harvesting and can produce weak growth. Start with the crop’s light requirement and then adjust for your structure, district and cooling system.
Start with the crop and cooling system
The crop is the first decision point. Fruiting vegetables need good light to set flowers and fill fruits. They can suffer in extreme radiation, but they also lose yield if kept under heavy shade for the full season. Seedlings and leafy crops have a lower light demand and tolerate more shading.
The second decision point is your polyhouse climate control.
- Naturally ventilated polyhouse (NVPH): Heat escapes mainly through side ventilation, roof vents and open curtains. In hot, dry inland areas, moderate external shading is often needed during peak summer.
- Fan-and-pad polyhouse: A correctly sized and maintained system reduces incoming air temperature. Because cooling is available, these houses usually need less permanent shading than NVPHs. Excess shade can become a bigger yield risk.
- Nethouse: The net itself is the main roof covering. Select the shade percentage carefully because there is no diffused polyfilm above it to modify incoming light.
- Polyhouse with white diffused polyfilm: Diffused film already spreads light more evenly through the canopy. Adding a dense shade net over it can reduce total crop light sharply, especially in cloudy spells.
If you are comparing structures before purchasing material, see the practical differences between an NVPH and a fan-and-pad polyhouse and between an NVPH and nethouse.
Recommended summer shade ranges by crop group
Use these as starting ranges, not as a fixed prescription. Variety, plant age, local solar intensity, cloud cover, planting density and the duration of shading all matter. In Rajasthan, Vidarbha, north Karnataka, Telangana and interior Tamil Nadu, peak April–June conditions may call for a different approach than coastal or high-elevation locations.
Crop group or use | Typical summer shade range | Where it usually fits | Important caution |
|---|---|---|---|
Tomato, capsicum, cucumber, muskmelon | 20–30% with effective fan-and-pad cooling; 30–40% in NVPH | Fruiting vegetables in high radiation | Avoid heavy all-season shade; poor light reduces fruit set, colour and yield. |
Chilli, brinjal and similar fruiting crops | 30–40% | NVPH or nethouse in hot districts | Watch flowering and internode length; excessive shade makes plants soft and lanky. |
Leafy vegetables, coriander, herbs | 35–50% | Nethouse, nursery or summer production | Ventilate well, as dense crop covers can hold humidity. |
Vegetable seedling nursery | 40–50% initially | Germination and early seedling stage | Harden seedlings gradually before transplanting into brighter conditions. |
Gerbera and many cut-flower nurseries | About 50–60% depending on site and crop stage | Warm-season protection | Confirm the requirement for the cultivar and production system. |
Shade-loving foliage ornamentals, some orchids and anthurium-type crops | 60–75% or crop-specific design | Dedicated shade structures | Do not use this level for tomatoes, cucumber or capsicum. |
A 50% net is a useful practical option for nursery work, leafy crops and some flower or ornamental crops. It is not automatically the best roof shade for every summer vegetable polyhouse. If your supplier provides a technical data sheet, check the stated shade factor and light transmission. The nominal percentage can vary with net colour, weave, age and how clean the material is.
Read your site conditions before finalising the percentage
Two farms growing the same capsicum variety can need different shading. Inspect these local factors before installing a net.
Solar intensity and hot months
Peak solar load is normally highest from March to June in much of peninsular and central India. Dry districts also face hot winds. In humid coastal areas, the temperature may be lower but humidity can be high, so ventilation and disease management become equally important.
For very harsh summer sites, do not jump straight to dense shade. First check whether hot air is trapped inside the house. Opening side curtains early, keeping insect net clean, maintaining roof vents, and improving air movement may solve part of the problem without sacrificing light.
Roof orientation and nearby shade
A structure exposed to full afternoon sun on all sides receives a different load from one partly shaded by trees or buildings. However, tree shade is uneven and can reduce crop uniformity. Assess the whole crop area, not just the coolest corner near the entrance.
Polyfilm condition
Dust, algae and ageing already reduce light transmission. If the polyfilm is dirty or nearing replacement, adding a shade net may push the crop into low-light conditions. Clean the cover safely and inspect tears, loose fittings and blocked vents before changing the shade plan.
Water and power reliability
A fan-and-pad system is only a cooling advantage when fans, pump, pads and power supply are reliable. During a power cut, crop temperature can rise rapidly. Keep a practical heat-stress plan, including manual ventilation and backup arrangements. Read how to prevent heat stress during polyhouse power cuts before relying on low shade percentages in a very hot site.
External net, internal screen or reflective net?
Where the shade material sits matters almost as much as its percentage.
Method | Main benefit | Main limitation | Best use |
|---|---|---|---|
External shade net above roof | Stops part of the solar energy before it reaches the cover | Needs secure support and wind-safe fixing | Peak summer reduction in NVPH and nethouses |
Internal shade screen below cover | Can be opened or closed by time and weather | Heat has already entered through the roof cover | Crops needing flexible daily or seasonal shading |
Reflective aluminium shade net | Reflects part of the radiation and can lower heat load | Check actual shade factor and installation method | High-radiation sites needing heat management |
Whitewash on polyfilm | Can reduce solar load over a broad roof area | Harder to reverse quickly and may cut light on cloudy days | Seasonal use where a planned, even reduction is needed |
For a summer NVPH, external shading usually gives a better heat-load reduction than putting the same net inside. Keep an air gap between the net and polyfilm where the design allows. Do not lay the net tightly on the film; rubbing, water pooling and trapped heat can damage the covering or reduce its life.
White, green and black nets can also behave differently in the crop environment. Colour affects reflected and transmitted light quality, not just the nominal shade value. For high-radiation polyhouses, reflective options deserve comparison, but select based on the crop response and verified product specification rather than colour alone. For a detailed operational comparison, see whitewash versus shade net for polyhouse summer cooling.
Use crop symptoms and measurements to fine-tune shade
Install a thermometer and humidity sensor at crop-canopy level, away from direct sun, wet pads and fan discharge. The useful question is not simply, “How hot is the outside air?” It is, “What temperature and humidity are the plants experiencing at midday?”
Check conditions between roughly 12 noon and 3 pm on clear, hot days. Compare readings at the centre, near side vents and near the fan or pad end. Learn correct placement from this guide on where to place temperature and humidity sensors in a polyhouse.
Signs that shade may be too low
- Upper leaves are curling, scorching or becoming leathery.
- Flowers abort during hot afternoons.
- Leaves wilt even when root-zone moisture is adequate.
- Fruits develop sunscald on exposed sides.
- Canopy temperature remains very high despite full ventilation or cooling.
These symptoms can also result from irrigation failure, high salinity, root disease or poor fan-and-pad performance. Diagnose the root cause before adding more shade.
Signs that shade may be too high
- Long internodes and thin, soft stems.
- Dark green but weak vegetative growth.
- Slow flower development and reduced fruit set.
- Delayed fruit maturity or poor colour in crops that need strong light.
- Persistently damp foliage and higher disease pressure.
Avoid judging from one hot day. Observe the crop over several days and compare with sensor records. If using a movable screen, close it during the harshest radiation period and open it later in the afternoon. This retains more useful light than permanent full-day shading.
A practical selection checklist
Follow this sequence before ordering or fitting summer shade material:
- Identify the crop stage. Seedlings, flowering plants and fruit-filling plants do not respond the same way to shade.
- Classify the crop’s light need. Fruiting vegetables generally need lower shade than nurseries, leafy greens and shade-loving ornamentals.
- Assess the structure. Note whether it is an NVPH, fan-and-pad house or nethouse, and whether white diffused polyfilm is already installed.
- Review the hottest four to eight weeks. Use last year’s crop records, local weather experience and midday readings from the current structure.
- Check ventilation first. Repair curtains, clear insect nets, inspect roof vents and service fans and pads before increasing shade.
- Choose the lowest effective shade range. For example, begin around 30–40% for a summer NVPH fruiting crop rather than using 50% by default.
- Plan removal or adjustment. Reduce shade as monsoon cloud cover increases or as the crop moves into a light-demanding fruiting phase.
- Secure the installation. Use a wind-safe support layout, avoid sharp edges and maintain enough clearance from the polyfilm.
For material specifications, including net-related terminology, use the protected cultivation specifications glossary. A complete material plan can be configured through the online kit builder, where item quantities and current weekly rates are shown.
Avoid common summer shading mistakes
The most common error is selecting shade percentage by what neighbouring farmers use. Their crop, elevation, irrigation water, ventilation and planting date may be different from yours.
Another mistake is keeping a heavy net on through cloudy monsoon days. Summer shade that protected a crop in May can restrict production in July or August. Inspect the crop after weather changes and make the system removable where possible.
Do not try to solve every heat problem with shade. A 50% net cannot compensate for blocked side vents, a failed pad pump, undersized exhaust fans or poor irrigation scheduling. In a fan-and-pad house, ensure the cooling system is matched and maintained; the guide to matching cooling pad area with exhaust fans is useful when reviewing the setup.
Finally, keep shade net clean and properly tensioned. Dust, torn sections and sagging areas create uneven light and airflow. Replace damaged sections before they become a crop-management problem.
Next steps
List your crop, planting stage, district, structure type and cooling equipment. Then select a preliminary range: low-to-moderate shade for well-cooled fruiting vegetables, moderate shade for NVPH vegetables, and higher shade only for nurseries, leafy crops or shade-loving ornamentals.
Before committing across the full area, test the choice in one bay where practical and record midday crop conditions for a week. Choose net material only after checking the stated shade factor, UV stabilisation, expected service conditions and the way it will be fixed to the structure. Polyhouse Constructions supplies shade-net and protected-cultivation material options; use the product data sheet and your local KVK or crop agronomist to confirm the final crop-specific decision.
Frequently asked questions
Is 50% shade net good for summer capsicum in a polyhouse?
It can be useful in a very hot naturally ventilated house, but it may be too much for capsicum if retained throughout the season. Many growers begin with a lower or moderate shade range and monitor flower set, plant growth and midday conditions before increasing it.
Should shade net go above or below the polyfilm?
For reducing summer heat load, an external net above the roof is generally more effective because it intercepts radiation before it passes through the film. It needs a safe support system and clearance from the polyfilm to avoid rubbing and heat build-up.
Can I use one shade net percentage for the whole year?
Usually no. A net suitable for peak April–June sun can reduce crop light too much during monsoon cloud cover or winter. Removable, retractable or seasonally changed shading gives better control where the budget and structure allow.
Does a fan-and-pad polyhouse need a shade net in summer?
It may need only light shading, or none at certain times, if the cooling system is correctly sized and operating reliably. The decision depends on local radiation, crop sensitivity, pad performance, airflow and power backup.
Which shade net colour is best for a polyhouse?
The best choice is not decided by colour alone. Compare the verified shade factor, light diffusion or reflectivity, crop need and installation position; a technical data sheet helps make a meaningful comparison.
