ఇది ఎలా పనిచేస్తుందివిడి సామగ్రి కొనండి

Pump Selection for Polyhouse Fogger and Cooling Pad Systems

Polyhouse Constructions Agronomy Desk · 13 నవం, 2026

A correct pump selection for polyhouse fogger starts with one question: are you feeding fogger nozzles or recirculating water over cooling pads? Do not use the same sizing method for both.

A fogger pump must deliver the required pressure at every nozzle and enough flow for the nozzles running in one zone. A cooling-pad pump must lift and circulate enough water evenly across the full pad header, while handling the required head and continuous running period. In both cases, water quality, pipe losses, motor duty rating and power availability matter as much as the pump’s HP label.

For the overall cooling arrangement, first ensure that the fan and pad sizes match. Read how to match cooling pad area with exhaust fans before finalising the pump.

Start with the equipment requirement, not pump HP

Do not select a pump only because a neighbour uses a 1 HP or 2 HP motor. HP is only the motor input rating. The useful pump output is the flow rate at a particular pressure or total head. This is shown on the pump performance curve.

Collect these details before speaking to a supplier:

  1. Number of fogger or mister nozzles, their individual flow and rated pressure.
  2. Number of zones that will operate together.
  3. For pads, total pad length, height and thickness, plus the pad maker’s water-flow recommendation.
  4. Height from the water level in the sump or tank to the highest outlet.
  5. Mainline and lateral pipe diameter, total route length, bends, valves, filters and pressure regulators.
  6. Water source: borewell, open well, storage tank or pad sump.
  7. Expected operating cycle: short intermittent fogging or long pad-pump operation.
  8. Electricity supply: single phase or three phase, voltage fluctuation and backup arrangement.

Ask for the pump’s Q-H curve. “Q” is flow, commonly in litres per minute (LPM) or m³/hour. “H” is head, in metres. A pump may give a high flow at near-zero head, but much less flow at the pressure your system actually needs.

Fogger pump selection: calculate flow and pressure together

The main job of a fogger pump is to create droplets that evaporate before wetting crop leaves. The required operating pressure depends entirely on the nozzle design. Do not guess it.

Low-pressure misters, medium-pressure foggers and high-pressure fogging nozzles are different products. A true high-pressure fogging system may need pressure in the tens of bar, whereas a simple mist line can work at much lower pressure. Check the nozzle data sheet for its rated pressure, discharge in LPM, filtration requirement and recommended line pressure.

See fogger versus mister for polyhouse cooling and humidity if you are deciding between these two systems.

Step 1: Calculate the design flow

Use the nozzle flow at the planned operating pressure, not at another pressure.

Design flow (LPM) = nozzle discharge (LPM) × number of nozzles running together

Then add a practical margin of around 10% to 20% for line variation, minor leakage and future adjustment. Do not add an excessive margin: an oversized pump can raise pressure too sharply, overload fittings and waste power.

Example:

If 40 nozzles operate in one zone and each gives 0.10 LPM at its rated pressure:

  • Basic flow = 40 × 0.10 = 4 LPM
  • With 15% margin = about 4.6 LPM

The selected pump should therefore deliver at least about 4.6 LPM at the required nozzle pressure plus line losses. It is not enough for its brochure to state 4.6 LPM at low pressure.

Zoning reduces the pump flow needed at one time. For example, 80 nozzles can be divided into two 40-nozzle zones. But each zone still needs stable pressure. Use suitable solenoid valves or manual valves, and avoid opening more zones than the pump is designed to serve.

Step 2: Calculate the pressure requirement

Pump pressure must cover:

  • nozzle operating pressure;
  • height difference from pump to the highest fog line;
  • friction losses in filters, pipes, elbows, valves and regulators; and
  • a small allowance for normal operating variation.

A useful conversion is:

1 bar is approximately 10 m of water head.

For example, a fogger nozzle needing 5 bar already needs approximately 50 m head in pressure terms. If the top fog line is 4 m above the tank and pipes/filters create an estimated 6 m loss, the pump duty point is roughly:

50 m + 4 m + 6 m = 60 m total head, at the calculated flow.

For high-pressure fogging, do not use this simplified calculation alone. Use the nozzle maker’s specified working pressure, an accurate pressure gauge near the far end of the line, and pump/filtration components rated safely above the operating pressure.

Why far-end pressure matters

A gauge only beside the pump can mislead you. The first nozzles may fog properly while the far-end nozzles drip or produce larger droplets. Install a gauge at, or temporarily test, the farthest working line. If pressure varies too much, review pipe diameter, zone size, filter blockage and pressure-regulator setting.

Correct fogger nozzle sizing must come before final pump sizing. More nozzles are not automatically better; excess fog can raise humidity, cause leaf wetness and encourage disease.

Cooling-pad pump selection: size for recirculation and even wetting

A fan-and-pad system normally uses a recirculation pump. It draws water from the pad sump and sends it to a top distribution header. Water flows down through the cellulose pad, collects in the gutter and returns to the sump.

This is different from fogging. The pad pump usually works at much lower pressure, but it must provide steady flow for long periods in hot weather. Its primary risk is not poor atomisation; it is dry bands, uneven wetting, overflow, algae/scale buildup or motor failure during peak summer hours.

The required flow depends mainly on the total installed pad length, pad thickness, header arrangement and manufacturer recommendation. Do not size it from polyhouse floor area alone.

Many pad suppliers specify a circulation rate in LPM per linear metre of pad. Exact values vary by pad design and thickness. Use that stated figure. If it is unavailable, obtain it from the pad supplier before buying the pump rather than applying a generic rule.

Pad circulation flow (LPM) = recommended LPM per metre of pad × total pad length

Add approximately 10% to 20% capacity margin after allowing for ordinary losses. The flow must be checked while the system is actually wetting all pad sections.

Compare fogger and cooling-pad pump duties

Selection factor

Fogger pump

Cooling-pad recirculation pump

Main purpose

Deliver fine droplets at controlled pressure

Keep the pad face uniformly wet

Key starting data

Nozzle flow and rated pressure

Pad length and recommended circulation rate

Usual pressure need

Varies widely; can be high for true fogging

Low to moderate; enough for lift and header distribution

Operating pattern

Short cycles, often in zones

Longer runs during heat load

Water route

Source/tank through filters to nozzle lines

Sump to header, through pads and back to sump

Critical check

Pressure at the farthest nozzle

Even wetting with no dry strips or overflow

Common wrong choice

Choosing on HP without checking pressure at flow

Choosing too small for the total pad length or lift

Calculate total dynamic head for either system

Total dynamic head (TDH) is the head against which the pump must work. It has three practical parts:

TDH = static head + friction head + required outlet pressure head

For a cooling pad, the outlet-pressure component is generally modest. For foggers, it may be the largest part of the calculation.

1. Static head

Static head is the vertical lift from the lowest operating water level to the highest outlet point. Measure the water level, not just the bottom of the tank. A falling sump or tank level increases the lift.

2. Friction head

Friction occurs as water moves through pipe, filters, valves, bends and fittings. It rises sharply if the pipe is undersized or the flow is increased.

Include:

  • suction pipe and foot valve losses;
  • sand/media filters, screen filters or disc filters;
  • non-return valves and solenoid valves;
  • elbows, tees and reducers;
  • long mainlines and small laterals; and
  • a partly clogged filter under real field conditions.

Avoid very long, narrow suction lines. Keep the pump near the water source where possible, use a properly sized suction pipe and prevent air entry at joints. Centrifugal pumps push water more reliably than they pull it.

3. Outlet pressure head

For foggers, convert the nozzle pressure from bar to head and add it to the calculation. For pads, the header should distribute water evenly but does not need fogger-level pressure. Excess pad pressure can create splashing and uneven flow instead of better cooling.

After calculating TDH and flow, locate that flow on the pump curve. Select the pump whose curve provides the required flow at that TDH, preferably near its efficient working range rather than at either extreme of the curve.

Match pump type, duty cycle and water source

The pump type should suit the job as well as the calculation.

Fogger systems

A fogging system may need a multistage centrifugal pump, booster pump, diaphragm-type unit or another pressure-capable arrangement suited to the nozzle pressure. The exact choice depends on pressure, flow and control layout. Confirm that seals, hose, fittings, filters and pressure regulator are all rated for the operating pressure.

If fogging runs in frequent short cycles, use a controller arrangement that does not force rapid, damaging motor starts. Depending on the system design, this may involve zoning, a pressure-control arrangement or a correctly specified pressure tank. The supplier should confirm the safe starting frequency for the motor.

Cooling-pad systems

For a pad sump, a corrosion-resistant centrifugal recirculation pump is commonly used. It should be rated for continuous or extended duty because it may run for much of a hot afternoon. Choose materials suited to the water quality, especially where water has high dissolved salts or the pad sump is treated for hygiene.

Provide an overflow route and a safe minimum water level. Never let the pump run dry. A float switch or low-level cut-off can prevent seal damage and motor overheating.

Borewell or storage-tank water

Do not connect untreated borewell water directly to fogger lines if it contains silt, hardness or iron. Fogger orifices are small and clog easily. Cooling pads also suffer from mineral scale, though the problem develops differently.

Test source water for suspended particles, hardness, alkalinity, iron and salinity where possible. Use filtration suited to the nozzle or pad supplier’s requirement. Clean or backwash filters on schedule, and monitor pressure drop across them. For complete planning, read water filtration needed for foggers and cooling pads.

Installation and commissioning checklist

Use this checklist before accepting a new pump system:

Do this test in warm conditions, when the system is under realistic demand. A system that appears satisfactory for five minutes in the morning can fail to maintain pressure after filters load up or when several zones open.

Common pump-selection mistakes

Buying by HP alone: Two pumps with the same motor HP can give very different flow at 40 m, 60 m or 100 m head. Always compare curves.

Using one pump for both pads and foggers without engineering review: Their pressure, filtration, duty cycle and water paths differ. Separate systems are often simpler to control and maintain.

Ignoring filter pressure loss: A new filter is clean; field filters become loaded. Allow for normal pressure drop and maintain them.

Oversizing the fogger pump: A large pump with poor control may push water through nozzles too fast, cause leaks and make humidity management difficult.

Undersizing the pad pump: Pads develop dry areas, leaving warm air to enter the crop zone. The exhaust fans may be correct but cooling performance will still suffer.

No backup plan: In peak summer, fan-and-pad cooling is sensitive to power interruptions. Keep essential spares and plan backup power. See practical measures to prevent heat stress during polyhouse power cuts.

Next steps

Make a one-page pump schedule listing nozzle model, nozzle count per zone, pad length, tank level, pipe sizes, filter type and target operating hours. Give this schedule to the pump supplier and ask for a curve-based selection, not only an HP recommendation.

If you are planning a new protected structure, you can build a material kit and view this week’s item-wise rates for the structure, covers, nets and fittings. Finalise the cooling equipment layout with your irrigation or climate-control designer so that pump capacity, electrical load and water treatment are planned together.

Frequently asked questions

Can I use a domestic pressure pump for polyhouse foggers?

Only if its pump curve delivers the nozzle maker’s required pressure and total flow after allowing for height and pipe losses. Many domestic pumps may run a few nozzles but cannot maintain uniform far-end pressure across a larger fogger network.

How much extra pump capacity should I keep for a fogger system?

A margin of around 10% to 20% above calculated design flow is commonly practical when selected at the required total head. Too much oversizing can make pressure control difficult, so do not use a large margin without a regulator and suitable bypass arrangement.

Should the cooling-pad pump run continuously in summer?

It should run according to the temperature, humidity and fan-and-pad control strategy for the crop and local weather. During intense heat it may run for long periods, so use a pump rated for extended duty and check sump water level regularly.

Why are some cooling-pad sections dry even though the pump is running?

Common causes are insufficient recirculation flow, an uneven header, blocked distribution holes, incorrect levelling, blocked filters or scale in the pad/header. First inspect water distribution along the top of the pad before increasing pump size.

Does hard borewell water damage foggers and cooling pads?

Hard water can leave mineral deposits in nozzles, filters, headers and cellulose pads, reducing performance over time. Test the water and use filtration and water-management practices recommended by the equipment supplier and your local agronomist.

మీ కిట్ తయారు చేయండి