ఇది ఎలా పనిచేస్తుందివిడి సామగ్రి కొనండి

Safe CO2 Levels and Timing for Polyhouse Crops

Polyhouse Constructions Agronomy Desk · 13 నవం, 2026

Plants use carbon dioxide (CO2) for photosynthesis, but only when enough light, water, temperature control and nutrition are available. For a commercial polyhouse, the safe CO2 level for polyhouse crops is usually 700–900 ppm during the bright part of the day. A well-controlled fan-and-pad house may use 800–1,000 ppm, but pushing concentration higher rarely pays when other crop conditions are limiting.

Do not inject CO2 at night. Do not inject it while natural vents are open or exhaust fans are running. In an Indian naturally ventilated polyhouse, daytime leakage is normally high, so CO2 enrichment is usually difficult to justify. Treat it as a controlled-environment tool, not a routine input like irrigation.

What CO2 level should you maintain?

Outdoor air is now commonly around 420 ppm, though the reading near a crop can change with time of day, nearby traffic, soil respiration and ventilation. In a closed polyhouse, crop photosynthesis can pull CO2 below outdoor concentration after sunrise. This is when modest enrichment can help—provided the crop has light and the structure can retain the gas.

Use the crop-zone reading, not the concentration close to an injection pipe, to control dosing.

Situation

Practical CO2 concentration

What to do

Outdoor or fully ventilated house

Near ambient, often about 400–500 ppm

Do not enrich; fresh-air exchange determines the level

Closed house soon after sunrise

700–800 ppm

A useful conservative starting target

Bright daylight with good climate control

800–1,000 ppm

Use only with a reliable sensor, controller and minimal air leakage

Low light, severe heat, water stress or disease stress

Do not chase a high target

Correct the limiting condition first

Night, or when vents/fans are operating

No enrichment

Turn the CO2 supply off

For many Indian tomato, capsicum, cucumber, lettuce and flower crops, start at 700–800 ppm rather than immediately aiming for the upper range. Observe crop response, climate data, ventilation hours and input cost over several weeks. The suitable set point varies with crop variety, leaf area, radiation, season, planting density and the tightness of the structure.

Avoid operating above 1,000 ppm simply on the assumption that more CO2 means more yield. The response becomes smaller as concentration rises, while gas use, leakage losses and safety management increase. Any system should have a conservative high-level cut-off and alarm set by a competent supplier or agronomist. Worker exposure limits are separate from plant targets and may differ under applicable workplace rules; do not use an occupational limit as a crop set point.

Why daylight timing matters

CO2 is the carbon source for photosynthesis. Photosynthesis needs light. During darkness, leaves do not use added CO2 to build sugars; instead, plants and soil or growing media respire and release CO2.

The useful window is therefore from after sunrise until before sunset, with the best response generally when sunlight is adequate and the crop is actively photosynthesising. In practice, do not begin enrichment at first light. Wait until the crop receives useful light and temperature has reached its normal working range. Stop before light falls sharply in late afternoon.

A workable daily sequence

  1. Check the morning climate. Verify that the CO2 sensor, temperature sensor and ventilation controls are operating. Do not dose if a sensor fault is showing.
  2. Allow useful daylight first. Once the crop is receiving reasonable natural light, begin controlled dosing if the house is closed.
  3. Maintain a modest target. Use pulse dosing or proportional control to hold the crop-zone level around the chosen set point, rather than continuously releasing gas.
  4. Stop before ventilation begins. Shut off CO2 before roof vents, roll-up side curtains, exhaust fans or other outside-air systems operate.
  5. Stop before evening low light. As radiation falls, end enrichment. Do not run it through the night.
  6. Log readings and gas use. Compare CO2, temperature, relative humidity (RH), ventilation status and crop observations. This identifies waste and control faults.

Cloudy monsoon days are a common reason to reduce or skip enrichment. The crop may have less light, while the need to manage RH and disease risk may require ventilation. Similarly, during peak summer, a fan-and-pad house may need frequent or continuous cooling. CO2 dosing then becomes uneconomical because air is being replaced rapidly.

Why you must not apply CO2 during ventilation

Ventilation is designed to replace warm, humid indoor air with outside air. It also removes injected CO2. With open roof vents, side curtains or exhaust fans, an enrichment system can empty a cylinder or run a generator with little increase at canopy level.

There are three reasons to interlock CO2 with ventilation:

  • Input loss: Most of the added CO2 escapes before the leaves can use it.
  • Poor control: Wind direction and fan airflow cause uneven concentrations. A sensor at one location may not represent the rest of the crop.
  • Safety: Dosing into a space where workers may enter, without dependable measurement and alarms, is unsafe. CO2 is colourless and odourless, and it can collect in low areas if released heavily.

For a naturally ventilated polyhouse (NVPH), side insect net and roof ventilation are essential for heat and humidity management. The house is intentionally leaky compared with a fan-and-pad facility. Read more about what an NVPH is and how it differs in NVPH vs fan and pad. In most daytime conditions, the vents need to remain open. That is why an NVPH is generally not the first choice for active CO2 enrichment.

In a fan-and-pad polyhouse, close the ventilation path only for a planned enrichment period, and only while temperature and RH remain within the crop’s acceptable range. Never keep a house closed merely to retain CO2 if the crop is overheating or humidity is climbing. Climate control comes first.

An HAF (horizontal airflow) fan is different from an exhaust fan. HAF fans circulate internal air and may help mix CO2 through the crop when correctly arranged; they do not deliberately exhaust air outdoors. Their placement still matters for even distribution. See this guide on HAF fan placement for even airflow.

Match CO2 enrichment to light, temperature and crop health

CO2 cannot compensate for a weak crop or poor climate. If the crop is heat-stressed, short of water, suffering root disease, or receiving very little light, stomata may close and photosynthesis remains limited. In such conditions, extra CO2 has little benefit.

Before starting a CO2 programme, check these basics:

  • Light: Diffused polyfilm can spread available light, but shade, cloud and dust still reduce radiation. Do not dose heavily under very dark conditions.
  • Temperature: Keep the crop within the normal range for its stage and species. A high CO2 target does not justify high summer temperature.
  • Humidity and VPD: Very high RH reduces transpiration and raises disease risk. Manage the moisture problem before sealing the house for gas retention. Use VPD to manage polyhouse temperature and humidity as part of the decision.
  • Water and fertigation: Maintain stable root-zone moisture and a crop-appropriate nutrient programme. CO2-driven growth can increase water and nutrient demand.
  • Canopy condition: A healthy, actively growing canopy is more likely to respond than a young, recently transplanted or stressed crop.

In cooler winter mornings, a closed polyhouse may retain CO2 better, but condensation and high RH can become serious. If ventilation is needed to dry the crop, ventilate first and stop CO2. Learn practical methods to reduce winter condensation.

Equipment and sensor setup that supports safe control

A basic timer alone is not enough for reliable enrichment. At minimum, use an accurate CO2 sensor suited for greenhouse conditions, a controller, a regulated source of CO2 and a means to stop dosing automatically when ventilation starts.

Place the main sensor at crop-canopy height, away from the direct stream of a CO2 outlet, doorways, cooling-pad air path and exhaust fans. For a long or multi-span house, validate readings at several points during commissioning. CO2 can stratify or form local pockets, especially when airflow is weak.

Essential control interlocks

Your controller should stop CO2 dosing when any of the following occurs:

  • roof vents or side curtains open;
  • exhaust fans start;
  • a high CO2 alarm threshold is reached;
  • sensor communication fails or the reading is implausible;
  • the emergency stop is activated;
  • power failure or controller fault creates an uncertain operating state.

Calibrate and bump-check the sensor according to its manufacturer’s instructions. A drifting sensor can cause chronic under-dosing, wasting money, or over-dosing, which creates a safety risk. For broader sensor planning, see where to place temperature and humidity sensors. CO2 monitoring should be added to—not substituted for—temperature and RH monitoring.

Cylinder-based CO2 is often easier to control cleanly than combustion-based generation. A combustion generator adds heat and water vapour, which may be unwanted in Indian conditions. Poor combustion can also introduce harmful gases. Never use vehicle exhaust, an improvised burner, charcoal or any unapproved combustion source for CO2. Use only purpose-designed equipment, follow its safety manual, and have the system installed and checked by qualified personnel.

Worker safety and operating discipline

A crop target of 700–1,000 ppm is far lower than concentrations associated with acute CO2 danger, but safety must not depend only on a target number. Leaks, sensor faults, incorrect regulator settings and dosing in a closed room can cause local build-up. CO2 is heavier than air and can settle in pits, sumps, low service spaces or poorly ventilated corners.

Keep staff safe with clear operating rules:

  • Put a visible sign at every entry stating when CO2 enrichment is active.
  • Train staff to stop the system before entering for prolonged work, unless the site safety procedure specifically permits entry.
  • Fit audible and visual alarms as part of the system design, and test them routinely.
  • Keep cylinders upright, secured and protected from heat. Check hoses, regulators and connections for leaks.
  • Ventilate the structure before routine maintenance, and never work alone in a suspected high-CO2 area.
  • Record incidents, alarms, cylinder changes and sensor calibration dates.

If anyone feels breathless, dizzy, unusually tired or unwell in a suspected high-CO2 area, move them to fresh air immediately and seek medical assistance. Do not re-enter until the area has been ventilated and the cause has been checked.

Is CO2 enrichment worth it for your structure?

CO2 enrichment tends to make more sense in a relatively sealed, sensor-controlled fan-and-pad polyhouse growing a high-value crop through periods when cooling demand is low to moderate. It is less suitable for a nethouse or for an NVPH that remains open for most of the day.

Calculate the decision from measured facts: how many daylight hours the house can stay sufficiently closed, the average CO2 level without dosing, gas consumed per day, crop response, market value and extra labour or equipment cost. Read when CO2 enrichment is worth it in a polyhouse before buying a system.

The structure also affects how well a climate-control plan works. For material options such as polyfilm, insect net, exhaust fans and circulation fans, see all protected-cultivation products. Material requirements and live weekly rates can be checked by building a kit online.

Next steps

Start with a one-week climate audit before investing in CO2. Log canopy-level CO2 from sunrise to sunset, ventilation status, temperature, RH, light conditions and worker entry times. If the house can remain closed during bright daytime periods without compromising crop climate, test a conservative 700–800 ppm target under professional guidance.

Keep the system interlocked with vents and exhaust fans from day one. If you cannot measure concentration accurately and shut dosing off automatically, do not enrich. In most Indian NVPHs, better ventilation, irrigation uniformity, disease prevention and temperature management will give a stronger first return than added CO2.

Frequently asked questions

Can I use CO2 enrichment in a naturally ventilated polyhouse?

It is possible only for short periods when the structure is genuinely closed, but it is often not economical. Open side curtains and roof vents quickly remove the added CO2, especially in hot or windy weather.

Does CO2 enrichment increase yield in every crop?

No. A healthy crop with adequate light, water, nutrients and suitable temperature is needed to benefit. Results differ by crop, variety, growing season and the number of closed daylight hours available.

Should CO2 be released near the floor or above the crop?

Distribution should be designed so the gas mixes uniformly through the canopy, not concentrated at one point. Confirm the result with readings at canopy height in more than one part of the house.

Can I run foggers while applying CO2?

Foggers do not necessarily exchange indoor air, so they can operate if the CO2 level, RH and temperature remain under control. However, excessive humidity can harm crop health, so the climate controller must prioritise crop-safe conditions over CO2 retention.

How often should a CO2 sensor be checked?

Inspect its reading and controller response daily during use, and follow the manufacturer’s scheduled calibration and functional-check procedure. Also test ventilation interlocks and alarms regularly, especially before a new crop season.

మీ కిట్ తయారు చేయండి