Polyhouse Film Replacement Procedure: Change Cover Safely Without Damage
Polyhouse Constructions Agronomy Desk · 13 నవం, 2026
A sound polyhouse film replacement procedure protects the new cover from tears at the start and keeps it tight through wind, heat and rain. The key is simple: work on a calm, dry day; prepare every frame contact point; unfold and pull the film evenly; then fasten it from the centre outwards without over-stretching it.
Do not treat film replacement as a one-person job. For a small single-span structure, arrange enough trained helpers to hold the roll, guide the sheet and operate ladders safely. For a large multi-span or gutter-connected house, use an experienced protected-cultivation erection team. A rushed pull in gusty wind can crease, puncture or permanently stress a new cover.
Plan the change for the right day and crop stage
The best replacement window is between crops, after removing crop residue, strings, trellising waste and loose objects from the house. This gives workers clear access and prevents a falling tool or sharp crop support from damaging the new sheet.
Choose a day with these conditions:
- Low wind: Postpone if gusts are expected. Even a light large sheet can act like a sail.
- Dry weather: Do not install during rain, heavy dew, or when the frame is wet and slippery.
- Moderate temperature: A cool-to-mild morning after dew has dried is usually practical. Avoid the hottest afternoon, when hot film expands and can later become loose as temperatures fall.
- Enough daylight: Start early enough to complete at least the main roof fastening in one day. Never leave an unfastened film rolled over the roof overnight.
- No major rain forecast: Roof work, gutters and ridge areas must remain safe and dry during the job.
Before fixing the date, measure the roof again. Do not order a replacement film only from an old invoice. Check the span profile, roof length, end-wall allowance, gutters and the actual fastening method. A roof profile affects both film width and the way water moves across the cover; see this guide on choosing a polyhouse shape and roof profile.
Check the replacement film and hardware before opening the roll
Keep the roll in its original packing, under shade and off wet ground until the frame is ready. Dragging a roll over concrete, gravel or GI edges can score the film before installation begins.
For most naturally ventilated polyhouses, replacement cover is selected for the structure design and crop requirement. Confirm the film’s width, length, micron thickness, UV stabilisation and any functional properties such as diffused light or anti-drip effect. Film service life varies with quality, UV exposure, local heat, dust, chemical contact, roof tension and handling. If you are unsure whether the old cover has reached replacement stage, review the common signs that a polyhouse film needs replacement.
Check that these items are available before the old cover comes off:
Item | Why it matters | What to check |
|---|---|---|
New polyfilm roll | Main weather cover | Correct width, length, orientation and specification for the house |
Lock channel and zig-zag spring/wiggle wire, or approved clamps | Holds film without point loading | No bent, rusted, sharp or loose sections |
Protective tape or padding | Separates film from rough frame points | UV-stable material suitable for polyhouse use |
End-wall and side fastening material | Secures edges and overlaps | Enough length for the full perimeter |
Clean ladders or work platform | Safe access to ridge and gutters | Rubber feet, stable footing, no sharp exposed edges |
Soft broom, cloth and basic hand tools | Cleaning and minor preparation | No sharp tool left on roof or film |
Do not reuse damaged spring wire, cracked clamps or badly corroded channels merely to save time. These parts can create concentrated pressure, allowing the film to flutter and tear. If you need replacement components along with the cover, you can buy individual polyhouse materials after matching them to your frame and fastening system.
Prepare the frame before removing the old cover
A new film should never be installed over a frame that has sharp burrs, protruding bolts, loose fittings or abrasive rust. These defects may not show immediately, but repeated wind movement will rub the film until it fails.
Clean and inspect all film-contact surfaces
Start at one end and inspect every place where film touches the structure:
- Arches, purlins and ridge members: Remove dust, dried mud, string, old tape and sharp debris. Look for rough weld spatters, cut pipe edges and damaged galvanising.
- Gutters and valley sections: Clean leaves and soil. Ensure drainage outlets are open before the new cover is fitted. Standing water near film edges increases leakage risk.
- Lock channels, clamps and bolts: Tighten loose fittings. Replace bent channel sections and cover or correct exposed bolt threads where they contact the film.
- Padding or anti-hotspot tape: Renew tape where it has become brittle, detached or worn through. It reduces abrasion and heat transfer at frame contact points.
- Side curtains and insect-net interfaces: Check that roll-up parts work freely and no net wire, broken clip or curtain edge can rub the roof cover.
Also inspect the GI structure for distortion, loose bracing or corrosion before covering it. Film replacement is the easiest time to reach the roof members. For a more complete inspection, use an annual polyhouse structure maintenance checklist.
Remove the old film in a controlled manner
Photograph the existing fastening arrangement before removal, particularly at ridge, gutters, end walls and corners. It helps when restoring overlaps and vents.
Release the old cover section by section. Remove spring wire or clamps carefully instead of cutting randomly across the sheet. Roll or fold the old film as you remove it. This keeps it from catching on pipes, damaging side nets or blowing into nearby crops. Wear gloves and eye protection when handling old wire, but do not let tools touch the new roll.
Unroll and position the new film without scuffing it
First confirm the manufacturer’s marking for the outside and inside face, if provided. Some films are designed with a particular orientation. Fixing the wrong face outward may affect its intended performance.
Carry the roll using enough people or a suitable roll-handling arrangement. Do not pull it across the ground. Position it parallel to the ridge or as specified for your roof and fastening design. On many roof covers, the sheet is drawn over the arches from one side toward the other, but multi-span, gutter and ridge-vent layouts can need a specific sequence.
Use clean guide ropes only where necessary. Keep ropes broad, smooth and free from knots or metal hooks. Never throw a rope over the frame with a stone, nut bolt or other weighted object tied to it. That common shortcut can puncture both old and new film.
When drawing the film up:
- Keep helpers spaced across the width so the load is shared.
- Lift and guide the sheet; do not drag it over gutters, ridge caps or purlin edges.
- Stop immediately if a corner catches. Release tension, identify the obstruction and correct it.
- Keep the film off hot metal surfaces where possible, especially in strong afternoon sun.
- Keep footwear, ladders, rings, watches and tools away from the sheet.
Do not walk directly on polyfilm. If access at height is necessary, use a properly supported ladder, mobile platform or safe roof-access method suited to the structure.
Tension the film evenly, not as tightly as possible
The aim is a smooth, firm cover with enough allowance for normal temperature movement. Excess tension is as harmful as slackness. An over-tight film can split around clips, channels or corners when it contracts in cooler weather. A loose film flaps in wind, wears against the GI frame and collects water.
A good working sequence is to make temporary, light holds first and then complete the final fastening in a balanced pattern.
A practical fastening sequence
- Align the sheet at the ridge or central reference line. Ensure equal planned overhang on both ends and sides.
- Make temporary holds at the centre of opposite edges. This prevents the sheet from shifting while the team checks alignment.
- Fasten the ridge or first main edge from the centre outward. Work alternately left and right, removing creases as you go.
- Pull the opposite side gradually and uniformly. Several workers should apply similar force along the length. Do not pull just from one corner.
- Secure side edges, then end walls. Continue from the middle towards corners rather than locking one end completely first.
- Finish corners, overlaps and vent details last. Use the approved overlap direction so rainwater sheds outward, not into the joint.
- Walk around and inspect under daylight. Look for diagonal wrinkles, tight stress lines at clips, loose pockets and unprotected rubbing points.
For lock channel systems, seat the film smoothly in the channel and insert the spring wire progressively. Do not hammer the wire or force it through a kinked channel. For batten or clamp systems, use the approved spacing and method for that structure. Fasteners should hold the film continuously without cutting, pinching or making isolated high-stress points.
Film tension is best judged by appearance and response, not by pulling until it feels hard. The cover should be smooth with no obvious fluttering panels, but it must not show whitening, stretched lines or severe pull at a corner. Recheck tension in the cooler part of the day and after the first few hot-cool cycles. If a panel becomes loose, correct it early using the correct fastening method; this guide explains how to tighten a loose polyhouse cover safely.
Protect vulnerable areas after fastening
Most early tears begin where film rubs a fixed object. Give extra attention to the ridge, gutter edges, corners, end-wall curves, door tops and side-curtain interfaces.
At each location, check for:
- Film touching a raw GI edge, bolt thread or weld bead.
- A sharp bend in the film as it enters a channel.
- Loose spring wire ends that can scrape the sheet.
- A crease leading from a corner or clip.
- Water paths that can enter under an overlap.
- Side curtains, insect nets or shade nets rubbing the new roof cover during operation.
Operate roll-up curtains slowly once before handing the house back to production. If the curtain frame catches, correct it before wind causes repeated rubbing. Also clean gutters and check roof runoff after the first rain. Good drainage is especially important in multi-span houses; see how to design polyhouse gutters for heavy rain.
Common mistakes that shorten new film life
Avoid these shortcuts during a film change:
- Installing in windy weather or leaving half-fixed film overnight.
- Pulling film from one corner, creating diagonal stress and uneven tension.
- Reusing rusted channels, damaged clips or exposed old fasteners.
- Skipping frame cleaning and protective tape replacement.
- Dragging the roll on soil, gravel, concrete or over a gutter edge.
- Fastening when the film is extremely hot and expanded.
- Overstretching to remove every small wrinkle.
- Letting workers walk on the film or place tools on it.
- Ignoring a loose side curtain, sharp insect-net wire or damaged door detail.
A correctly specified replacement cover is only one part of the job. The fastening system and frame condition decide whether that film stays intact. Learn more about suitable cover options on the polyfilm product page.
Next steps
Measure the structure, inspect the fastening system and schedule replacement between crops on the first suitable calm, dry day. Order the film with compatible channels, springs, clamps and protective materials rather than treating the cover as a stand-alone purchase.
For a material list matched to your structure, use the kit builder with live weekly rates. If the frame needs major rectification, roof-height access or a full cover change on a large house, arrange trained installation support before opening the new roll.
Frequently asked questions
Can polyhouse film be replaced while the crop is inside?
It is possible only in limited situations, but it carries a high risk of dropping dust, old wire or tools onto the crop. Plan a full roof-cover change between crops whenever possible, especially for vegetables on trellises.
How much extra polyfilm should be kept at the edges?
The required allowance depends on roof shape, fastening channel position, end-wall detail and gutter arrangement. Measure the actual structure and follow the cover layout for that design rather than using one fixed extra length for every polyhouse.
Should polyfilm be installed tightly in winter or summer?
Install it in moderate, stable weather rather than extreme heat or cold. Film expands in heat and contracts in cooler conditions, so final tension should allow normal movement without visible slack or stress marks.
Can I use nails or ordinary screws to fix polyhouse film?
Direct nails and ordinary screws create point loads and holes that can spread into tears. Use the fastening channel, spring wire, clamp or batten system designed for the structure and film.
What should be done with the removed polyhouse film?
Keep it separate from farm waste and soil, then send it through an available agricultural-plastic recycler or authorised local collection route. Do not burn old polyfilm, as it creates harmful fumes and disposal problems.
