Polyhouse Heating Options in Winter for Vegetable Crops
Polyhouse Constructions Agronomy Desk · 13 నవం, 2026
Winter heating is needed only when the night temperature inside the polyhouse falls below the crop’s safe range. For many Indian vegetable farms, improving heat retention, closing leaks and managing humidity will be enough. In frost-prone belts, high-altitude areas, or for warm-season crops such as cucumber and capsicum planted through a cold spell, active heating may protect growth and fruit quality.
For most farms, start with passive heat retention. If active heat is essential, electric heaters suit small, reliably powered areas; indirect-fired diesel or LPG systems suit controlled heating; and biomass boilers can suit larger units with dependable fuel and trained labour. Do not use an unvented flame inside a closed crop area.
First decide whether the crop actually needs heating
A polyhouse is warmer than the outside air during a sunny day, but at night it loses heat through the cover, gaps, soil and ventilation openings. On a clear winter night, crop-level temperature can also be lower than the air temperature because leaves lose heat to the cold sky.
Heating is most justified for:
- Cucumber: a warm-season crop that slows sharply in cold root zones and cool nights. Aim to avoid prolonged exposure below roughly 15°C.
- Capsicum: can tolerate cool conditions better than cucumber, but low night temperatures can slow growth, reduce fruit set and delay harvest. A night root-zone and air temperature around 16–18°C is commonly preferred during active growth.
- Tomato: many protected varieties can manage cooler nights, but growth, pollen performance and harvest timing suffer if temperatures remain too low for long periods. The exact threshold depends on variety and crop stage.
- Nursery seedlings: young plants are less forgiving than established plants. Heating a small nursery compartment is often more economical than heating a full block.
Cool-season vegetables such as lettuce, leafy greens, broccoli and many herbs usually need frost protection and ventilation management rather than high air temperatures. Excess heating may produce soft growth and raise humidity.
Use a shielded temperature and relative humidity (RH) sensor at crop height, not beside a heater, side curtain or roof. Also record outside temperature. Correct sensor placement in a polyhouse makes these records useful for choosing a heater and setting its thermostat.
Comparison of polyhouse heating options in winter
The best heat source depends on heated area, climate, electricity reliability, local fuel access and how closely you can supervise the system. The table gives a practical comparison.
Heating option | Best fit | Main advantages | Main limitations | Key rule |
|---|---|---|---|---|
Passive retention | Every polyhouse; mild to moderate winter | No fuel cost, lowers heat loss, improves uniformity | Cannot lift temperature enough during hard frost | Do this before buying a heater |
Electric unit or fan heater | Small nursery, small compartment, short cold events | Clean at point of use, simple thermostat control | Requires sufficient sanctioned load and backup; costly for large spaces | Keep equipment dry and use proper electrical protection |
Diesel-fired indirect heater | Medium to large houses, cold zones, regular heating | High output, fuel logistics often practical | Needs flue, maintenance, safe fuel storage and good combustion | Keep combustion gases outside crop air |
LPG-fired indirect heater | Clean, controllable heating where cylinders/bulk gas are dependable | Fast response and less soot than poorly maintained diesel | Fuel supply and cylinder handling; direct firing adds moisture | Prefer externally vented/indirect systems |
Biomass boiler with hot-water pipes | Large, regularly heated projects near reliable biomass supply | Can give stable root-zone or air heat; fuel may be locally available | High initial complexity, ash, labour, storage and fire risk | Use a boiler room and trained operation, not open burning |
A heater’s purchase cost is only one part of the decision. Compare total seasonal cost: fuel or electricity, wiring or piping, chimney/flue, thermostat and controls, labour, routine servicing, backup arrangements and expected crop value.
Passive heating: the first and lowest-risk option
Passive measures reduce the heater capacity and running hours required. They also keep temperatures more even after the heater switches off.
Seal the structure without stopping planned ventilation
Before winter, inspect ridge and side joints, door edges, roll-up curtains and polyfilm overlaps. Repair tears promptly. Close side curtains before sunset when cool air begins entering, but do not make the polyhouse permanently airtight. Crops still need planned morning ventilation to remove moisture.
A good covering matters. A properly tensioned, UV-stabilised diffused film reduces drafts and helps retain heat better than a damaged cover. For material specifications such as film, nets and fittings, see the protected cultivation product range. Keep insect-net openings and required ventilation paths functional; do not block them with loose sheets that can fall onto plants or create unsafe airflow.
Use thermal screens and double-layer solutions where suitable
An internal thermal screen or night curtain can reduce radiation heat loss from the crop to the roof. It must be opened in the morning so crops receive light and so trapped moisture does not persist all day. Design and operation matter: a poorly managed screen can increase condensation and disease pressure.
Double-poly inflation systems are another option for purpose-designed structures in colder locations. The insulating air layer reduces night heat loss, though it needs correct film selection and a maintained inflation blower. It is not a simple retrofit for every naturally ventilated polyhouse.
Manage soil, water and crop-zone heat
Moist soil stores more daytime heat than very dry soil, but over-irrigation in winter cools the root zone and raises RH. Irrigate at a time that allows the crop and soil surface to dry before night where crop needs permit.
Water-filled thermal mass, such as sealed water containers, can soften a small night temperature dip if warmed by daytime sun. Its effect is modest in a large commercial house. Do not depend on water barrels alone during frost. For high-value cucumber, capsicum or nursery production, hot-water root-zone heating is more targeted, but it normally requires a boiler or heat pump and good design.
Electric heating: clean and practical for small zones
Electric resistance heaters convert nearly all electricity used at the unit into heat. Portable fan heaters, fixed unit heaters and ducted heaters are common formats. They are often best for a germination room, seedling bench, propagation tunnel, pack area or a separated small bay rather than a whole acre-scale polyhouse.
Their main benefit is control. A thermostat can start the heater near a chosen low-temperature set point, and there are no combustion products in the crop space. However, do not assume the existing electrical connection can carry the load. Check sanctioned load, cable size, earthing, MCB/RCCB protection, three-phase balance where relevant, and generator or battery backup needs.
Place heaters so warm air moves across the crop instead of blowing continuously at one bed. Pair them with horizontal air circulation fans where needed. Air movement reduces hot and cold pockets but should be gentle enough not to cause leaf stress. Review the electricity load calculation for polyhouse equipment before selecting an electric system.
Electric resistance heating becomes expensive when used for large volumes through many cold nights. An appropriately designed heat pump can reduce electricity use compared with resistance heat, but performance falls in very cold outdoor conditions and installation needs specialist assessment.
Diesel and LPG heating: choose indirect, vented equipment
Diesel and LPG can provide substantial heat quickly. Their safe use depends on separating combustion from crop air.
Why indirect-fired heating is preferred
An indirect-fired heater burns fuel in a sealed combustion chamber. A heat exchanger transfers heat to clean air, while exhaust leaves through a correctly installed flue. This is the suitable approach for enclosed vegetable production.
A direct-fired heater releases combustion products into the polyhouse. Even when carbon dioxide may appear useful, fuel burning also produces water vapour and, if combustion is incomplete, harmful gases such as carbon monoxide, nitrogen oxides and soot. The added water vapour can push RH up just when winter crops are already prone to condensation, botrytis and leaf disease. Do not use open flame heaters, stoves, angithis or diesel burners inside a closed crop area.
Diesel versus LPG
Diesel equipment is often considered where output demand is high and fuel supply is easy to organise. It needs regular burner servicing, filter checks, clean fuel and a safe tank or container arrangement. Poor combustion creates soot and lowers efficiency.
LPG generally gives cleaner combustion at the burner, and cylinder supply can be convenient for smaller installations. Cylinders must remain upright, protected from heat and physical damage, and managed according to applicable safety rules. LPG is heavier than air, so leaks can collect in low areas. Never check a leak using a flame.
For either fuel, install carbon monoxide monitoring in relevant enclosed service areas, keep extinguishers ready, maintain clear access to exits and have a shutdown procedure. A diesel heater safety checklist is useful even if the final choice is LPG because the principles of ventilation, fuel isolation and maintenance are similar.
Biomass heating: useful at scale, but only with disciplined operation
Biomass heating usually means a boiler using agricultural residues, pellets, briquettes or wood chips to heat water. That hot water then circulates through pipes, unit heaters or root-zone lines. It can work well for a larger protected cultivation project that has regular cold-season demand, reliable dry fuel and staff to operate the system.
Its strength is thermal stability. A correctly designed hot-water loop can distribute heat more evenly than a few hot-air heaters. Buffer tanks can store heat and reduce rapid temperature swings. Root-zone lines can also warm plants efficiently because the plant roots receive heat directly.
The practical challenges are serious:
- Fuel moisture and size must be consistent. Wet biomass burns poorly and creates smoke.
- Fuel needs covered storage away from the boiler room.
- Ash removal, tube cleaning and water treatment are routine jobs.
- A boiler, chimney, pumps, expansion provisions, safety valves and insulated pipes need professional design.
- Fire protection and trained operators are essential.
Do not burn crop waste, plastic mulch, treated wood or mixed waste in or near the polyhouse. Smoke and fumes can damage crops and people, while ash and sparks create a fire hazard.
Size and operate the heating system around the coldest hours
Heater size cannot be chosen by floor area alone. Heat loss depends on cover surface area, structure shape, film layers, air leakage, wind, outside design temperature, desired inside temperature and whether you use a thermal screen. A humid, windy night in a hill location needs more capacity than a calm night on the Deccan plateau.
Use a qualified designer to calculate the heat load. The guide on how to calculate heater capacity for a polyhouse explains the inputs to collect. Specify capacity for the local design night, then keep a reasonable margin for unusual cold and heat losses at doors and vents.
Operate with these steps:
- Set a crop-specific lower threshold. Avoid heating to daytime-like temperatures at night. A modest safe night set point is normally more economical and healthier for the crop.
- Start heat before the crop reaches stress temperature. A thermostat at canopy level works better than waiting for visible leaf damage.
- Mix air gently. Warm air rises, so circulation fans help prevent cold pockets at plant level.
- Vent briefly when needed. On sunny winter mornings, open ventilation enough to remove humid air, even if outside air is cool. Avoid a sudden cold blast on wet foliage.
- Track RH and leaf wetness risk. Heating lowers RH temporarily, but watering, crop transpiration and combustion can bring it back up. Read more about reducing winter condensation.
- Keep backup ready. Have a generator for electrically controlled heaters and fans, spare fuel where permitted, and a manual emergency response plan.
Safety and crop-health checklist
Use this checklist before the first cold spell:
Next steps
Begin with three nights of inside and outside temperature records, plus RH at crop height. Then identify whether the issue is a short pre-dawn dip, repeated frost, cold root zones or persistent moisture. Fix leaks and use passive retention first; select an active system only for the remaining heat gap.
For a new structure or winter retrofit, plan heating alongside cover, curtains, ventilation and electrical layout. Polyhouse Constructions supplies material kits and individual structure materials; you can build a kit and view this week’s item-wise rates before finalising the structure side of the project. For heater installation, flues, boilers and electrical work, use qualified specialists and follow local safety requirements.
Frequently asked questions
Can I heat a naturally ventilated polyhouse in winter?
Yes, but heat loss through vents, side curtains and gaps must be controlled first. A naturally ventilated house is usually suited to passive retention or limited frost protection; sustained whole-house heating needs careful sealing and humidity management.
Which is the cheapest polyhouse heating option in winter?
Passive measures such as repairing leaks, using night screens and managing curtains have the lowest operating cost because they do not consume fuel. Among active systems, the lowest seasonal cost varies with local electricity tariff, fuel availability, heater efficiency and labour.
Can I use an LPG burner directly inside a polyhouse?
It is not advisable in a closed vegetable crop area. Direct combustion adds moisture and can release harmful gases if burning is incomplete; use indirect-fired, externally vented equipment designed for the purpose.
Do winter vegetables need heating every night?
No. Leafy greens and other cool-season crops often need only protection from frost or severe cold. Warm-season vegetables, young seedlings and crops grown in cold locations may need heating on selected nights, especially before dawn.
Will heating solve fungal disease in a polyhouse?
Heating can lower relative humidity for a time, but it will not solve disease by itself. Control condensation through morning ventilation, irrigation timing, air circulation, crop spacing and sanitation, and seek advice from your KVK or crop agronomist if symptoms appear.
