இது எப்படி வேலை செய்கிறதுதனிப் பொருட்கள் வாங்க

Polyhouse Irrigation Water Testing Before Crop Planting

Polyhouse Constructions Agronomy Desk · 12 நவ., 2026

Water testing should be completed before you transplant any crop in a polyhouse. A basic laboratory report can reveal salinity, pH, bicarbonates, sodium, clogging minerals and microbial contamination that may otherwise cause weak growth, blocked drippers, nutrient imbalance or root disease.

For most protected crops, send a fresh sample from the actual irrigation source to a recognised water-testing laboratory. Do this before each main crop cycle, and again if the water source changes after summer, heavy rain, flooding, borewell repair or tank cleaning.

Why polyhouse irrigation water testing matters

In open-field farming, rain and a larger soil volume may dilute some water-quality problems. In a polyhouse, irrigation is frequent, localised and controlled. Salts can build up near the wetted root zone, especially under mulch and drip. A small clogging problem can leave part of a bed dry while the rest looks normal.

Water quality affects three areas at the same time:

  • Crop health: High salinity, chloride, boron or sodium can reduce water uptake, scorch leaf margins and lower yield. Sensitive crops such as cucumber, capsicum and many flowers need closer monitoring.
  • Fertigation control: High alkalinity makes it harder to manage nutrient-solution pH. Calcium, magnesium and bicarbonates can react with fertilisers and form deposits.
  • Drip and disease hygiene: Silt, algae, iron bacteria and microbial contamination can block emitters or form biofilm inside pipes. Contaminated surface water may also introduce plant pathogens or create unsanitary handling conditions.

Do not judge water only by taste, colour or TDS meter reading. A TDS reading is useful for a quick field check, but it cannot show alkalinity, sodium hazard, iron, boron or microbial status.

The pre-planting water-test checklist

Ask the laboratory for an irrigation-water analysis, not only a drinking-water report. If you run hydroponics or cocopeat grow bags, tell the laboratory this too; dissolved minerals matter even more in soilless systems.

Request these checks:

  1. pH and electrical conductivity (EC): The first indicators of acidity/alkalinity and total dissolved salts.
  2. Alkalinity and bicarbonates: Important for nutrient-solution pH and scale formation.
  3. Calcium, magnesium and total hardness: Needed to judge scaling risk and to count useful calcium and magnesium in fertigation planning.
  4. Sodium, chloride and SAR: These show possible salt injury and soil-structure risk in soil beds.
  5. Iron and manganese: Common causes of brown, black or slimy deposits and dripper clogging.
  6. Boron: A trace nutrient, but harmful at a low excess concentration for many crops.
  7. Nitrate and sulphate: These contribute nutrients and can indicate contamination or excess salts.
  8. Turbidity, suspended solids and sediment: Essential for choosing filters.
  9. Microbiological indicators: Particularly total coliforms and E. coli where water is from ponds, canals, open tanks or other surface sources.

For soil-grown crops, also test the soil separately. A good water report does not correct an already saline or poorly drained bed. This is especially important if the previous crop had uneven growth or crusting around drippers.

How to collect a sample that gives a useful report

A poor sample can produce a misleading result. Take water from the point that represents what plants will receive, preferably after the pump and before fertiliser injection. If you want to compare source water with delivered water, take separate labelled samples.

Sampling steps

  1. Use the laboratory’s clean bottle if possible. For microbial testing, use only the sterile bottle provided by the lab.
  2. Run the borewell, pipeline or pump for about 5 to 10 minutes before sampling. This clears standing water from the line.
  3. Do not take the sample immediately after adding fertilisers, acids, disinfectants or cleaning products to the system.
  4. Fill the bottle without touching its inside or cap interior. Leave the headspace requested by the laboratory.
  5. Label each bottle with source, date, time and location. For example: “Borewell, pump outlet, 12 June”.
  6. Keep microbial samples cool and deliver them to the laboratory promptly, following its instructions. These samples should not sit in the sun or in a vehicle for hours.
  7. Record the water level, recent rain, source changes and any visible sediment, smell or staining. This context helps interpret an unusual result.

If your farm uses a borewell plus stored rainwater, pond water or tanker water, test each source separately. Mixing water can change EC, alkalinity and microbial risk substantially.

Reading the main results before planting

The numbers below are practical screening ranges, not universal pass-or-fail limits. Suitable limits vary with crop, rootstock, soil texture, drainage, season, irrigation frequency and whether you grow in soil, cocopeat or hydroponics. Use the full report with your agronomist or KVK to make the final fertigation plan.

Test parameter

Generally favourable starting range

What a high or abnormal result can mean

What to plan before planting

pH

About 5.5–7.5

Nutrient availability or difficulty adjusting fertigation pH

Check alkalinity before deciding on correction

EC

Below about 0.7 dS/m is easier to manage

Excess dissolved salts; reduced water uptake

Improve drainage, consider blending or choose tolerant crops/rootstocks

Alkalinity

Below about 60–120 mg/L as CaCO₃ is usually easier

Persistent rise in root-zone or stock-solution pH; scale risk

Plan pH management with professional guidance

Bicarbonate

Below about 120 mg/L is generally manageable

Calcium/magnesium deposits and higher pH

Review acidification and fertiliser compatibility

Sodium / SAR

Low sodium and SAR below about 3 are preferable for soil beds

Soil sealing, poorer infiltration and salt accumulation

Improve drainage and review calcium balance

Chloride

Below about 70 mg/L suits sensitive crops better

Leaf-edge burn and salinity stress

Avoid chloride-heavy inputs; consider blending if feasible

Boron

Below about 0.3–0.5 mg/L is safer for sensitive crops

Toxicity in sensitive vegetables and flowers

Seek crop-specific advice before planting

Iron and manganese

Ideally very low; around 0.1 mg/L or less each reduces clogging concern

Deposits, biofilm and emitter blockage

Use suitable oxidation/filtration where required

Turbidity / suspended solids

Clear water with low sediment load

Sand-media and screen filters may clog quickly

Install and maintain staged filtration

EC is not the same as pH

This confusion causes many avoidable mistakes. EC measures the total level of dissolved salts. pH indicates acidity or alkalinity. Water can have an acceptable pH but too much salinity, or a low EC but excessive alkalinity. Both values are needed.

For a naturally ventilated polyhouse in hot weather, frequent irrigation can partly manage a moderate EC source only if the soil drains well and a planned leaching fraction is possible. In a poorly drained heavy soil, the same water can quickly create a root-zone salinity problem. In cocopeat or hydroponics, account for the source-water EC before adding fertilisers; otherwise the final nutrient EC may become too high.

Check clogging risk from the source to the dripper

Blocked drippers often start with a water-quality issue, not a dripper-quality issue. Clogging can be physical, chemical or biological, and more than one type may occur together.

Physical clogging

Sand, clay, organic debris and algae are common in ponds, canals and unprotected storage tanks. Inspect the filter flush water and open a few line ends before planting. If sediment is visible, do not assume a screen filter alone will manage the load.

Chemical clogging

Water with high bicarbonates, calcium and magnesium can form scale. This becomes more likely when pH rises or incompatible fertilisers are mixed in a stock tank. Iron and manganese may oxidise after pumping and form deposits that collect in filters, laterals and emitters.

Biological clogging

Slime inside filters or laterals may indicate algae, bacterial growth or iron bacteria. Warm stored water and uncovered tanks increase this risk. Keep tanks covered, prevent light entry where practical, clean filters and flush mainlines and laterals on a documented schedule.

Before transplanting, run plain water through every irrigation zone. Check pressure at the first and farthest points, inspect filter condition, and measure emitter discharge from a small sample of drippers. Uneven discharge is a crop-uniformity problem that should be solved before seedlings are planted.

For routine maintenance, use this guide on drip irrigation hygiene for polyhouse crop protection.

Treat microbial risk as a crop-protection issue

A clear borewell sample is often lower risk than untreated surface water, but no source should be assumed clean. Pond water, canal water, runoff collection and open tanks can receive soil, animal waste, decaying leaves and plant debris. These can introduce high microbial loads and organic matter.

Microbiological testing does not identify every crop pathogen. However, total coliforms and E. coli are useful hygiene indicators. Their presence means the source or storage system may be exposed to faecal contamination and needs investigation. Ask the laboratory or agronomist whether further pathogen testing is justified, especially after disease outbreaks or flooding.

Use source protection first:

  • Keep storage tanks covered and clean.
  • Prevent runoff, animal access and crop waste from entering ponds or tanks.
  • Remove algae and sediment before they enter the drip system.
  • Use effective filtration and, where needed, a properly designed water-treatment system.
  • Avoid wetting foliage unnecessarily, particularly late in the day or during humid weather.

Water treatment must match the problem. Filtration removes particles but does not reliably remove dissolved salts. Disinfection can reduce microbial risk but does not remove salinity, bicarbonates or iron minerals. Have the system designed and monitored by a qualified irrigation professional; treatment without checking the actual water report can waste money or damage the crop.

Good water management works together with root-zone sanitation. Read safe irrigation practices to prevent root diseases and the polyhouse sanitation checklist between crop cycles before bringing in seedlings.

Turn the report into a crop plan

Do not file the laboratory report away after installation. Use it to make decisions before ordering seedlings and fertilisers.

If EC, chloride or sodium is high

Choose the crop and rootstock carefully, maintain drainage, and assess whether blending with better-quality water is practical. Monitor root-zone EC during the crop, not only source EC. In soil beds, a drainage plan is essential; salts cannot be managed by adding more water if there is nowhere for excess water to move.

If alkalinity is high

Calculate fertiliser and pH-management requirements using the water report. Avoid guessing based on pH alone. The agronomist should consider bicarbonate level, source-water calcium and magnesium, crop stage and the fertilisers being used.

If iron, manganese or sediment is high

Finalise filtration and flushing arrangements before transplanting. Check filter type, capacity and cleaning frequency against the measured load. Keep spare filter elements or service provisions ready during the crop.

If microbial indicators are present

Investigate the source, storage tank and distribution system. Clean the system and introduce a suitable treatment and monitoring programme. Do not use a water-quality correction as a substitute for cleaning infected crop residue, tools or nursery trays.

Seedling health also matters. Inspect incoming plants carefully with this seedling health checklist before entering a polyhouse.

Next steps

Take samples from every irrigation source at least a week or two before planting, so there is time to interpret the report and make corrections. Check the filtration system, flush each zone and verify pressure and dripper uniformity before transplanting.

Keep the laboratory report, source EC readings, filter-cleaning record and fertigation changes in one crop file. If you are setting up a new protected structure or replacing material, you can build a material kit with live weekly rates and review the item quantities before purchase. Water quality and irrigation design should be planned together, not after the crop begins.

Frequently asked questions

How often should I test polyhouse irrigation water?

Test before every major crop cycle and whenever you shift from one source to another. Retest after heavy rain, flooding, borewell servicing, a sharp change in EC, recurring dripper clogging or unexplained crop stress.

Can I use borewell water directly for drip irrigation in a polyhouse?

Many farms do, but borewell water still needs testing for EC, bicarbonates, sodium, iron and manganese. Clear-looking borewell water can have dissolved salts or minerals that affect crops and block drippers over time.

Is a handheld TDS meter enough for water testing?

No. A TDS or EC meter is useful for regular monitoring, but it cannot measure bicarbonates, sodium adsorption ratio, boron, iron, microbial contamination or suspended solids accurately.

What water quality is best for cucumber and capsicum in a polyhouse?

These crops generally perform better with low-salinity water, low chloride and boron, and manageable alkalinity. The acceptable range depends on the growing medium, drainage, cultivar and climate, so use a crop-specific fertigation plan.

Can filter systems remove salt from high-EC irrigation water?

Normal sand, screen and disc filters remove particles, not dissolved salts. High-EC water may require blending, crop and rootstock selection, drainage management or specialised treatment after professional assessment.

உங்கள் கிட்டை உருவாக்குங்கள்