HAF Fan Selection for Polyhouse: Air Throw, Capacity and Crop Height
Polyhouse Constructions Agronomy Desk · 13 நவ., 2026
Horizontal airflow (HAF) fans are recirculation fans. They do not remove hot air from the structure like exhaust fans. Their job is to move air continuously around the crop, reducing still pockets, evening out temperature and humidity, and helping foliage dry after irrigation or condensation.
For sound HAF fan selection for polyhouse, begin with the actual fan air throw at your required air speed, not blade diameter or motor HP alone. Then check its airflow capacity in m³/h, mounting height above the crop, motor protection and service support. A fan that is large on paper but loses its air stream before reaching the next unit will not give uniform circulation.
Start with the crop and structure, not the catalogue
Measure the enclosed growing space before seeking quotations. Record:
- Length, width and gutter height of each compartment
- Number and width of spans, posts and trellis lines
- Crop type, final canopy height and row direction
- Benches, partition curtains, pack area or other obstructions
- Whether the house is naturally ventilated or uses fan-and-pad cooling
- Available electrical supply: single phase or three phase, voltage and panel capacity
HAF is useful in naturally ventilated polyhouses, but it becomes especially important in a closed or partly closed fan-and-pad house. Exhaust fans and cooling pads create air movement from pad to fan. That is not the same as air circulation within the crop canopy. HAF fans help mix the air across the width and length, including periods when exhaust fans are off or running at a low stage.
First decide whether you need circulation fans, exhaust fans, or both. For evaporative cooling equipment, use a separate calculation for exhaust fan size in a fan-and-pad polyhouse. Do not substitute HAF fan capacity for exhaust ventilation capacity.
The four specifications that matter most
A supplier should provide a technical data sheet, not only a photograph and an HP value. Compare fans on the following points.
Specification | What it tells you | What to check before purchase |
|---|---|---|
Airflow capacity | Volume of air moved, normally in m³/h or CFM | Compare ratings at the stated test condition; do not compare unmatched CFM and m³/h claims |
Air throw | How far a useful air stream travels | Ask for throw at a stated terminal air speed, ideally around 0.25–0.5 m/s |
Fan diameter and discharge pattern | Shape and reach of the air stream | Check guard size, clearance and whether the stream will pass above, through or across the canopy |
Motor and electrical rating | Reliability and operating cost | Verify phase, kW/HP, full-load current, IP rating, thermal protection and speed |
Airflow capacity: use m³/h, but do not select on it alone
The m³/h rating indicates the fan’s circulation capacity. A larger crop volume, a dense indeterminate tomato canopy, or a long multispan compartment normally needs more total circulation than a short house with a low leafy crop.
However, two fans with similar rated m³/h can behave differently in a real polyhouse. Blade design, discharge cone, guard resistance, mounting arrangement and obstructions affect the air stream. Capacity tells you how much air is moved; air throw tells you whether that movement reaches the required area.
As a practical starting point, design for a gentle, continuous air movement around the crop, often about 0.25–0.5 m/s at canopy level. The correct target varies by crop, weather, growth stage and whether fogging, heating or CO₂ enrichment is used. Very high air speed directly on tender seedlings, flowers or fruiting clusters can cause mechanical stress and excess water loss.
Air throw: the deciding figure in long houses
Air throw is the distance at which the air stream falls to a specified speed. It is meaningful only when that end speed is stated. For crop circulation, ask the supplier: “What is the measured throw at 0.25 m/s or 0.5 m/s?”
Do not accept a single throw figure without knowing the test condition. A claim of 20 m throw at a high velocity is not necessarily useful for a 20 m fan spacing where gentle canopy air movement is needed.
For a typical HAF loop, the discharge from one fan should reach close to the next fan or overlap with it. In a long house, this often means choosing a fan and spacing that create an unbroken circulation path rather than leaving a dead zone in the middle. Trellis wires, crop density and internal shade screens shorten effective throw, so retain a margin rather than designing exactly at the published maximum.
Motor type: select for humid farm conditions
A polyhouse motor works in warm, humid, dusty conditions. Moisture can be high early in the morning, especially in winter or during monsoon. A suitable motor is therefore as important as the blade.
Look for:
- TEFC motor: Totally enclosed fan-cooled motors are generally preferable where humidity and dust are present.
- IP protection: IP55 or a higher suitable protection level is a common preference for wet and dusty agricultural environments. Confirm the full motor specification, not only the fan housing.
- Thermal overload protection: This helps protect against overheating, though the electrical panel must also have correctly sized protection.
- Copper winding and quality bearings: Ask for documented motor and bearing details, along with warranty terms.
- Compatible supply: Single-phase fans can suit small compartments where only single-phase power is available. For larger installations with several fans, three-phase equipment can offer more practical load distribution.
- Speed control compatibility: If variable speed control is proposed, confirm in writing that the motor and controller are compatible. Not every AC motor performs safely on every speed controller.
An energy-efficient motor can reduce recurring electricity use, but first ensure it provides the required throw and can operate reliably under local voltage conditions. A voltage relay, proper earthing and correctly rated contactors are often worthwhile safeguards.
Match the fan to crop height and canopy density
The air path must serve the crop, not merely move air near the roof. Crop height changes through the season, and this affects both mounting height and fan direction.
For low leafy vegetables, nursery plants or young crops, fans can be mounted lower than in a tall tomato, cucumber or capsicum crop. But retain enough clearance for workers, spray booms, trellis operations and the fan guard. In tall trellised crops, fans are normally installed above the mature canopy, with the discharge set so that the main stream travels just over or through the upper crop zone and then returns down the opposite side of the circulation loop.
A useful field check is to inspect airflow after the crop reaches its dense stage. Ribbon indicators tied safely at several points can show where air is weak. Check the centre of bays, corners, near side curtains, below shade screens and the lowest part of the crop. Do this with the house in its normal operating condition.
Avoid these common errors:
- Mounting fans too high, so air stays near the roof.
- Mounting them too close to the crop, causing a harsh stream on leaves and flowers.
- Directing a fan into a roof truss, screen, curtain or dense trellis block.
- Designing based on an empty structure and ignoring a mature canopy.
- Keeping the same fan angle all season when crop height changes substantially.
Plan a circulation loop before fixing quantities
HAF fans work best as a planned system. They are usually arranged to send air down one side of the house and return it along the other side, forming a horizontal loop. The exact layout depends on house length, width, bays, obstructions and fan throw.
A practical selection sequence
- Draw the compartment to scale. Mark columns, doors, cooling pads, exhaust fans, crop rows, internal screens and equipment.
- Set the mature crop canopy height. Use the highest expected canopy, not transplant height.
- Choose a candidate fan based on documented throw. Use its throw at a stated low terminal velocity suitable for crop circulation.
- Place fans in opposing directions. Create a loop around the crop area instead of aiming every fan in one direction.
- Keep spacing within effective throw. Allow overlap and reduce spacing where trellises, screens or dense crops interrupt airflow.
- Check cross-bay coverage. A very wide multispan house may need more than one circulation loop; one row of fans may not serve every bay.
- Validate after installation. Measure air movement or perform a practical ribbon/smoke-free airflow observation at crop level, then adjust angle or position.
For detailed positioning principles, see this guide to HAF fan placement for even polyhouse airflow. The layout should be finalised for each compartment, not copied blindly from another farm.
Check installation, noise and service details
A correctly selected fan can still fail early if its mounting or electrical work is poor. Use rigid brackets fixed to approved structural members. The fan should not shake, touch the crop-support system, or pull on flexible wiring.
Before commissioning, check that guards are secure, blades rotate freely, fasteners are tight and the fan direction matches the drawing. Use an isolator near the fan where appropriate, route cables safely away from irrigation lines, and provide reliable earthing. Electrical connections should be completed by a qualified electrician.
Noise and vibration are warning signs, not normal operating features. Persistent vibration can loosen brackets, wear bearings and damage the structure over time. Balance, mounting rigidity, blade condition and bearing quality should be checked before simply replacing the motor. Read the practical guide on HAF fan noise and vibration faults if an installed system is becoming noisy.
Also ask the supplier for:
- Rated power consumption and full-load current
- Wiring diagram and recommended protection
- Motor warranty, blade warranty and availability of spares
- Maintenance intervals for bearings, belts if fitted, guards and fasteners
- Performance curve or test information for airflow and throw
Avoid confusing HAF with cooling and humidity control
HAF fans improve uniformity. They do not lower air temperature below the outside condition by themselves, nor do they remove moisture from the house. They support other climate actions.
In hot, dry weather, fan-and-pad cooling may be required where the crop and project justify it. In humid monsoon conditions, running HAF alone may redistribute humid air but cannot replace controlled ventilation or dehumidification. Its value is that it reduces stagnant pockets where condensation and leaf wetness persist.
Coordinate HAF operation with exhaust fans, vents, foggers and shade management. For example, fans may run continuously or in timed cycles according to crop need, but avoid strong drafts immediately after foliar application. A controller can simplify operation in larger houses; smaller units may use a timer and manual checks. Sensor location also matters: a single sensor near a fan outlet will not represent crop conditions across the house.
A buying checklist for HAF fans
Before placing an order, confirm every item below:
When comparing hardware, read each item’s technical data sheet rather than relying only on HP. You can review air circulation fan options and other individual polyhouse materials alongside your structure plan.
Next steps
Prepare a scaled drawing of one polyhouse compartment and note its mature crop height, row layout and electrical supply. Ask each supplier for airflow capacity, air throw at a defined air speed, motor data and a proposed layout drawing. Compare the complete circulation plan, not just the number of fans or motor HP.
If you are planning a new protected-cultivation structure, build the structure material list and see current item quantities and weekly rates through the online kit builder. Then finalise HAF fan placement with the crop plan and local climate in mind.
Frequently asked questions
How many HAF fans are needed in a polyhouse?
There is no fixed number per acre or per 1,000 m² that suits every house. Quantity depends mainly on compartment length and width, the fan’s tested throw, crop density, mature crop height and obstructions such as trellis or screens.
Can I use an exhaust fan as an HAF fan?
Usually no. Exhaust fans are designed to move air out of the polyhouse against system resistance, while HAF fans are designed to project a circulation stream within the crop area. Use each fan for its intended purpose.
What HAF fan air throw should I ask for?
Ask for air throw at a stated terminal velocity, preferably in the gentle range relevant to crop circulation, such as 0.25–0.5 m/s. A throw figure without its end velocity or test condition is not enough for layout planning.
Should HAF fans run at night?
They may be useful at night or early morning when condensation and humidity are high, but the schedule depends on crop, season and actual temperature-RH conditions. Avoid creating a strong cold draft over sensitive crops, and use timers or controls based on observations.
Which motor is better for a polyhouse HAF fan: single phase or three phase?
Single phase can be practical for a small house with limited power availability. Three phase is often more suitable where several fans are installed, but the right choice depends on the sanctioned supply, load calculation and electrical panel design.
