How Many Sensors Does a Polyhouse Need? A Practical Sizing Guide
Polyhouse Constructions Agronomy Desk · 13 ਨਵੰ 2026
A practical answer to how many sensors for polyhouse is: start with one indoor temperature and humidity (RH) sensor for each climate zone, plus one outdoor sensor. Add indoor sensors when the house is long, has separate crop blocks, uneven airflow or different irrigation zones.
For a small naturally ventilated polyhouse of up to about 500 m² with one crop, this usually means two sensor locations: one inside at crop level and one outside in a shaded location. A long fan-and-pad house may need three or more indoor locations because the pad end and fan end do not experience the same temperature and humidity.
The aim is not to fill the polyhouse with instruments. It is to identify conditions that differ enough to change a decision on ventilation, cooling, irrigation or disease prevention.
Count climate zones first, not just total area
A sensor count should follow the number of independently behaving zones in your structure. A zone is an area where crop climate, irrigation or ventilation can differ from another area.
Treat areas as separate zones when they have any of the following:
- Separate fan, pad, fogger, roof-vent or curtain control
- Different crops, crop stages or canopy heights
- Different irrigation schedules or growing media
- A physical partition, curtain or separate bay
- A clear temperature or RH difference during the day
- One section close to an open side, entrance, pad wall or exhaust fans
For example, a 1,000 m² naturally ventilated polyhouse growing the same capsicum crop in one open block may work as one climate zone. But if half the house has young seedlings and half has a mature crop under a shade screen, count it as two zones.
A sensor can only represent the air around it. It cannot accurately represent a distant crop block with different sunlight, airflow or plant density.
Recommended sensor numbers by polyhouse size and type
The table below refers to indoor temperature-RH sensor stations. A station is generally one combined probe that measures both air temperature and relative humidity. Also install one outdoor temperature-RH reference station for the farm, regardless of the number of houses.
Polyhouse situation | Indoor temperature-RH stations | Outdoor stations | Why this is usually enough |
|---|---|---|---|
Up to 500 m² NVPH, one crop and one open block | 1 | 1 shared farm station | Climate is normally similar across the crop, though manual checks at ends are still useful. |
500–1,000 m² NVPH, or a house longer than about 30 m | 2 | 1 shared farm station | One station near the middle and one at the more variable end reveal side-vent and end-wall differences. |
1,000–2,500 m² NVPH with one crop | 2–3 | 1 shared farm station | Use one sensor per roughly 25–35 m of meaningful crop length, adjusted for airflow and openings. |
Fan-and-pad house up to about 30 m long | 2 | 1 shared farm station | Place stations near the pad-side crop and near the fan-side crop to check the cooling gradient. |
Fan-and-pad house 30–50 m long | 3 | 1 shared farm station | Pad end, middle and fan end readings help prevent one end being over-cooled or under-cooled. |
Fan-and-pad house longer than 50 m, or with partitions | 3–5 or one per control zone | 1 shared farm station | Longitudinal temperature and RH differences become more important, particularly in hot weather. |
Multiple crops or separately controlled compartments | 1 per compartment, minimum | 1 shared farm station | Each crop block needs its own representative reading. |
These are starting ranges, not fixed rules. A 600 m² house in a windy, uneven site can need two indoor points. Conversely, a compact 1,000 m² house with excellent air mixing may show little variation after monitoring.
Use length and airflow to decide extra sensors
Area alone can mislead. A 1,000 m² structure that is wide and short behaves differently from a narrow, 80 m-long structure.
Naturally ventilated polyhouses
In naturally ventilated polyhouses (NVPH), air conditions can change near side vents, doors and end walls. The difference is often strongest in summer afternoons, humid monsoon weather and periods of low wind.
For a uniform single crop:
- Start with one indoor station for a compact house up to about 500 m².
- Add a second station when crop length exceeds about 30 m, or when one end is more exposed to sun or wind.
- Add a third station for long houses above roughly 60–70 m, or where there are clearly different crop blocks.
If the controller operates roll-up curtains from one sensor, use the most representative central crop location as the control sensor. The other sensor should log and alert you to variation. It should not be ignored simply because it is not directly connected to the controller.
Before choosing the ventilation arrangement, understand the operating differences in NVPH versus fan-and-pad polyhouses.
Fan-and-pad polyhouses
Fan-and-pad cooling deliberately moves air from the cooling pad towards exhaust fans. The air becomes warmer as it travels across the crop. This makes sensor placement along the length essential.
A useful minimum layout is:
- One combined temperature-RH probe about 5–10 m from the pad wall, within the crop.
- One probe near the middle of the crop length.
- One probe about 5–10 m before the exhaust-fan wall.
For a house below 30 m long, the middle station may be omitted only after you have checked that end-to-end readings remain close during peak summer operation. Do not place the probe directly in pad discharge air or directly in the exhaust fan suction zone. Such readings are real, but they do not represent the crop climate.
Sensor readings also help verify whether air movement is uniform. Review how to choose an HAF fan and HAF fan placement for even airflow when end-to-end readings remain far apart.
Add sensors according to the decision you must make
Temperature and RH are the basic climate measurements. Other sensors are useful only when they support a specific management decision.
Sensor type | When it is worth adding | Suggested quantity |
|---|---|---|
Air temperature and RH | Every commercial polyhouse | One per indoor climate zone, plus one outdoor reference station |
Substrate moisture or tension sensor | Cocopeat bags, grow bags, raised beds or high-value drip crops | At least one representative plant location per irrigation zone; two locations are better for large or variable zones |
Root-zone EC and pH monitoring | Fertigation in soilless media or intensive production | One check point per fertigation recipe or irrigation zone; use regular drain-water testing as well |
Leaf wetness sensor | Frequent condensation, foliar disease risk, flowers or humid monsoon conditions | One in the dampest representative crop area; add one more in a separate wet zone |
PAR/light sensor | Shade-screen decisions, nursery work or research-oriented crop management | One representative indoor point; outdoor comparison is optional |
CO₂ sensor | Only where CO₂ is actively enriched or suspected to build up in a closed house | One per sealed, independently managed compartment |
Water pressure or flow sensor | Automation, foggers, cooling pads or many irrigation valves | One at the main line, plus one for each independently monitored critical zone if needed |
Do not confuse a low-cost soil moisture probe with a complete irrigation strategy. In cocopeat, readings vary with sensor position, bag moisture pattern and salt level. Use the sensor alongside drain percentage, drain EC, plant appearance and irrigation records.
For RH management, temperature alone is not enough. A temperature-RH station lets you calculate or view vapour pressure deficit (VPD), which is often more useful for crop response than RH by itself. Learn the working method in using VPD to manage polyhouse temperature and humidity.
Place sensors where plants experience the climate
Correct placement matters as much as the quantity. A badly placed sensor may make a good controller take poor decisions.
Indoor temperature and RH sensor placement checklist
- Mount the probe at or just above the active crop canopy, usually around 1–1.5 m high for many vegetable crops. Raise it as the crop grows.
- Use a radiation shield. Direct sun can make air temperature readings falsely high.
- Keep it away from roof film, metal members and side curtains that heat up or cool down faster than crop air.
- Keep it out of direct fogger spray and away from dripping condensation.
- Do not mount it immediately beside an exhaust fan, cooling pad, doorway or heater.
- Maintain enough clearance from leaves so the probe measures air, not the damp microclimate trapped inside foliage.
- Put duplicate stations at comparable canopy height so readings can be compared meaningfully.
The detailed layout principles are covered in where to place temperature and humidity sensors in a polyhouse.
Outdoor sensor placement
The outdoor station should be shaded and naturally ventilated. Keep it away from a hot wall, roof, generator exhaust, water tank and concrete surface. Place it at a representative farm location, not right beside the polyhouse pad discharge or exhaust outlet.
Outdoor temperature and RH help you understand whether the house is actually cooling, ventilating or dehumidifying effectively. They are also useful for setting alarms before hot afternoons or cold nights.
Separate control sensors from monitoring sensors
Not every sensor has to control equipment. This distinction reduces unnecessary automation cost.
A practical setup has three levels:
- Control sensor: The primary sensor connected to the controller. It switches fans, pads, curtains, foggers or heaters based on set points.
- Verification sensors: Extra indoor stations that show whether other parts of the crop are different from the control point.
- Alarm and record sensors: Devices that log trends, flag extreme heat, high RH or equipment failure, and support crop reviews.
For example, in a 48 m fan-and-pad polyhouse, the middle station may be the control point. Pad-side and fan-side stations can provide alerts. If the fan end repeatedly runs much warmer than the centre in summer, inspect fan capacity, inlet area, pad condition, air leaks and HAF circulation rather than simply lowering the controller set point.
Similarly, do not use one sensor near a wet pad to control humidity for the full house. It may keep foggers off even when the far end is too dry, or make the system react late to changing crop conditions.
Check variation before buying a large sensor network
A low-risk approach is to monitor first, then expand. This avoids paying for sensors that do not change any action.
Follow this simple process:
- Draw the house layout. Mark pads, fans, side vents, doors, partitions, crop rows and irrigation zones.
- Install the minimum setup. Use the table above for indoor and outdoor temperature-RH stations.
- Log readings for 7–14 days. Include hot afternoons, cool mornings, irrigation cycles and, if possible, rainy or humid conditions.
- Compare readings at the same time. Look for repeated differences, not a single unusual hour.
- Add a station where variation changes management. Examples include a persistently hotter fan end, a wet corner with condensation, or a separate young-crop block.
- Calibrate and maintain probes. Clean radiation shields, check wiring and compare sensors periodically. Low-cost RH sensors can drift in dusty or humid conditions.
As a working trigger, investigate if two stations in the same intended climate zone repeatedly differ by around 2–3°C in temperature or 10% RH during operating hours. The acceptable difference depends on crop, season and where the sensors are placed, so use this as a prompt to inspect rather than as an absolute standard.
Common mistakes that lead to wrong sensor counts
The most frequent mistake is buying one sensor for a large house because the controller has only one input. One input may control the system, but it does not prove the crop climate is uniform.
Avoid these errors:
- Counting square metres but ignoring a 40–60 m pad-to-fan airflow path.
- Using one sensor for two crops with different canopy height or climate needs.
- Installing all sensors at the same end of the house.
- Putting a sensor under direct sunlight or near a fogger nozzle.
- Buying CO₂, light or leaf-wetness sensors before basic temperature-RH sensing is reliable.
- Failing to inspect sensor data after ventilation, shading or crop layout changes.
- Assuming a faulty sensor is a crop problem. Compare with a second calibrated device before changing set points.
Next steps
Start with one temperature-RH station per real climate zone and one outdoor reference station. For long fan-and-pad houses, plan pad-side, middle and fan-side readings from the beginning. Add root-zone sensors only where irrigation is separately managed or the crop value justifies closer control.
When finalising the structure, keep sensor cables, power points and controller space in the layout plan. If you are planning a naturally ventilated polyhouse, fan-and-pad house or nethouse, you can build a material kit and view this week’s rates for the structure and material requirements. Then share the proposed crop, dimensions and equipment layout with your agronomist or automation supplier before fixing the final sensor schedule.
Frequently asked questions
Can one temperature and humidity sensor control an entire polyhouse?
It can control a small, uniform polyhouse, but it may not represent every crop area. In a long house or a fan-and-pad system, use additional monitoring sensors to check whether the far ends differ from the control point.
Do I need separate temperature and humidity sensors?
Usually no. A good combined air temperature-RH probe is practical for polyhouse climate control and data logging. Check that its stated accuracy and working range suit hot, humid farm conditions.
How many sensors are needed for a one-acre polyhouse?
There is no fixed one-acre count because layout and cooling system matter more than area alone. A one-acre house divided into separate bays needs at least one temperature-RH station per bay, while a long fan-and-pad block commonly needs multiple stations along its airflow path.
Where should a sensor be placed in a fan-and-pad polyhouse?
Place sensors within the crop, away from direct pad discharge and away from exhaust fan suction. For longer houses, compare readings near the pad side, middle and fan side at similar canopy height.
Are soil moisture sensors necessary in a polyhouse?
They are useful for drip-irrigated soil beds and especially for cocopeat grow bags, but they are not mandatory for every farm. Add them when you can act on the reading through separate irrigation scheduling, and verify readings with drain, EC and crop observations.
