ਇਹ ਕਿਵੇਂ ਕੰਮ ਕਰਦਾ ਹੈਵੱਖਰੀ ਸਮੱਗਰੀ ਖਰੀਦੋ

Bacterial Wilt Control in Polyhouse Tomato: Prevention Guide

Polyhouse Constructions Agronomy Desk · 12 ਨਵੰ 2026

Bacterial wilt control in polyhouse tomato starts before transplanting. Keep the pathogen out through healthy seedlings and clean water, prevent wet soil and runoff, use clean tools, and remove suspect plants without carrying soil through the house. Once a tomato plant is infected, there is no dependable curative spray, so fast action protects the remaining crop.

Know what bacterial wilt looks like

Bacterial wilt in tomato is commonly caused by Ralstonia solanacearum. It is mainly a soil- and water-borne disease. A polyhouse does not stop it automatically: warm conditions, repeated tomato cropping, wet beds and movement of contaminated soil can make the disease severe.

Typical symptoms are:

  • One or a few plants wilt suddenly, often first during the hot part of the day.
  • Wilt may become permanent even when the soil is moist and the plant is watered.
  • Leaves often remain green initially; obvious yellowing can come later.
  • The stem may show brown discolouration in the water-conducting tissue when cut lengthwise.
  • In advanced patches, nearby plants begin to wilt over days or weeks.

Do not diagnose from wilt alone. Root injury, blocked drippers, water stress, root-knot nematodes and Fusarium wilt can look similar. A clean cut stem placed in clear water may sometimes show bacterial streaming, but this is only an indication. Send fresh samples, including roots and surrounding soil, to a reliable diagnostic laboratory or take help from your KVK or crop agronomist.

How the disease enters and spreads in a polyhouse

The bacteria need an entry route. They can enter through injured roots, transplant wounds or natural root openings. They then multiply inside the plant and block water movement.

Risk route

What happens in the crop

Practical prevention

Infested field soil or old beds

Bacteria survive in soil, roots and plant debris

Avoid known wilt fields; rotate crops and treat beds before planting

Infected seedlings

Disease enters with the plug, root media or tray

Buy traceable seedlings and inspect every batch before entry

Surface water or contaminated storage

Water may carry soil and bacteria to many plants

Use protected, tested water sources; keep tanks covered and clean

Runoff and standing water

Contaminated water moves from one bed or bay to another

Make raised beds, drainage channels and prevent water pooling

Tools, footwear and hands

Soil stuck to a knife, shoe or trolley reaches clean rows

Assign tools by zone and clean/disinfect after soil contact

Crop debris and weeds

Roots and some weeds can maintain the pathogen

Remove crop roots and control weeds inside and around the structure

The highest-risk situation is a tomato crop planted again in the same soil after a wilt problem. Do not assume that removing last season's plants has removed the disease. Infected roots, soil particles and water pathways can remain important sources.

Prepare the site before tomato transplanting

Choose beds and drainage carefully

Protected tomato beds should drain quickly after irrigation or rain entry. This matters especially in naturally ventilated polyhouses during the monsoon, when runoff can enter through side areas or around the structure.

Make firm, raised beds and maintain clear drainage channels. Repair low spots where water stands. Do not allow wash water from outside, packing areas or another crop block to flow into tomato beds. Keep soil from outside fields away from the growing area.

Drip irrigation is preferable to flooding because it keeps paths and foliage drier. But drip is not automatically safe. Over-irrigation can still saturate the root zone and push contaminated water sideways through beds. Learn the basics of safe irrigation practices for root diseases before setting the irrigation schedule.

Break the tomato-after-tomato cycle

Avoid continuous tomato, brinjal, chilli or other susceptible crops in the same soil where possible. Rotate with a suitable non-host crop based on local advice and market demand. Rotation reduces risk but is not a guarantee because Ralstonia can survive for long periods in soil and on some weeds.

Remove volunteer tomato plants and weeds from inside the polyhouse, drains and nearby edges. They can act as bridges between crop cycles. A planned break crop, strict weed control and sanitation work better together than any single practice.

Use solarisation as one part of a programme

In hot, sunny months, moist soil covered with clear plastic can heat up and reduce some soil-borne disease pressure in the upper soil layer. Soil solarisation for polyhouse disease management explains the preparation and limitations.

Solarisation should not be treated as a complete cure for a heavily infested site. Its result depends on season, sunshine, soil moisture, treatment duration and depth of heating. It must be followed by clean seedlings, clean water and no movement of untreated soil back onto prepared beds.

Start only with clean, vigorous transplants

Seedling hygiene is the first practical barrier. Obtain plants from a nursery that can identify the variety, sowing date, tray and source of growing media. Ask whether the nursery has had bacterial wilt or unexplained wilting in its tomato batches.

Before accepting trays, inspect them at the entry point:

  1. Check for wilted, stunted, yellow or uneven seedlings.
  2. Lift a few plugs. Roots should be white to cream and active, not brown, slimy or badly damaged.
  3. Look for algae, standing water and dirty reused trays.
  4. Keep new trays away from established crops for a short observation period if space permits.
  5. Reject suspect lots rather than planting them in a clean bed.

Use a separate, clean area for handling seedlings. Do not place trays directly on soil paths. Workers should not move from old crop beds to transplant handling without cleaning footwear and hands. See this seedling health checklist before entering a polyhouse for a more detailed receiving routine.

Where bacterial wilt is a known recurring problem, grafted tomato plants on an appropriate resistant rootstock can reduce risk. Resistance varies by rootstock and local bacterial strain, and grafting cannot overcome severely infested soil or contaminated water. Read about grafting for bacterial wilt and soil disease control before choosing this route.

Keep irrigation water and drip lines clean

Water can spread a soil-borne disease across many rows faster than hand movement. Prefer a protected borewell or another clean source over untreated surface water where feasible. If water is taken from a pond, canal or open storage, the risk needs special attention.

Before the crop starts, test irrigation water for basic quality factors such as pH, EC, bicarbonates and microbial concerns relevant to your source. If bacterial wilt is suspected in the area, discuss targeted water or plant testing with a local laboratory. A routine water-quality report does not always prove that the source is free from wilt bacteria.

Follow these working rules:

  • Cover tanks so dust, insects, leaves and runoff do not enter.
  • Keep tank lids, filters, venturi equipment and fertigation containers clean.
  • Prevent soil or drain water from being sucked back into lines when pumps stop.
  • Flush drip laterals as required, collecting discharge away from crop beds.
  • Repair leaks promptly; a persistent leak creates a wet, high-risk patch.
  • Do not use a hose to wash soil from paths into drains that connect to beds.

Read the full drip irrigation hygiene guide when setting up cleaning and flushing records. If disinfection or line treatment is used, select only a product permitted for the system and crop, and follow its label directions and your agronomist's advice.

Use tool, worker and harvest hygiene every day

Bacterial wilt often moves with a small amount of wet soil. Treat soil contact as the main hygiene trigger, not only visible plant disease.

Keep separate tools for each production zone if possible. Label pruning knives, trowels, buckets and harvest crates. After work in a suspect row, first remove all soil and plant sap from tools; then use a suitable disinfectant according to its label. Disinfectants work poorly on dirty tools, so cleaning comes first.

Set up a simple entry routine:

  • Keep a footwear-cleaning point at the entrance.
  • Use clean, dedicated shoes or overshoes inside the crop area where practical.
  • Restrict visitors from entering production rows.
  • Ask workers to complete clean blocks before working in suspect blocks.
  • Do not share crates, knives or trolleys between a wilt-affected area and a clean area without cleaning.

At harvest, avoid dragging crates along wet beds or drains. Keep paths dry and remove damaged fruits and plant debris from the work area. A wider between-crop routine is covered in this polyhouse sanitation checklist.

What to do when one tomato plant wilts

Speed matters. Do not wait to see whether surrounding plants wilt, and do not try to revive a suspicious plant by increasing irrigation.

  1. Mark the plant and stop routine work in that row. Note the row, plant number, date and irrigation zone.
  2. Check the dripper and root zone. Rule out a blocked dripper or an obvious irrigation failure, but avoid digging around the plant unnecessarily.
  3. Get a diagnosis. Submit a representative fresh sample if symptoms fit bacterial wilt.
  4. Remove confirmed or strongly suspect plants carefully. Take out the plant with as much root system and attached soil as practical, without shaking soil onto nearby beds.
  5. Bag the material at the site. Move it out through a planned route. Do not compost infected plants within or near the polyhouse.
  6. Clean tools, footwear and hands. Treat the row as a separate work zone until assessed.
  7. Inspect nearby plants and irrigation points frequently. Watch the same bed, adjoining beds and the shared water line.
  8. Record the pattern. A map of affected plants helps identify whether the source is a seedling batch, a wet patch, a line leak or a drainage route.

Do not replant immediately into the same hole after a wilted plant is removed. This can place a new plant directly into contaminated soil. Ask your KVK or agronomist for a block-specific plan if cases are increasing.

A seasonal prevention checklist

Use this checklist before each tomato cycle, especially before monsoon planting or after a previous wilt issue.

Next steps

Start with a risk map of your polyhouse: mark old wilt patches, water entry points, leaks, drains and each seedling batch. Correct drainage and water hygiene before transplanting, then make tool cleaning and weekly scouting part of the normal work schedule.

If your protected structure needs better side protection, drainage planning or replacement material, review the available polyhouse materials. For a wilt-affected crop, work with your KVK, plant pathologist or experienced agronomist to confirm the diagnosis and make a crop-cycle plan rather than relying on a single product.

Frequently asked questions

Can bacterial wilt spread through tomato seed?

Seed is not usually the main source compared with infested soil, water and seedlings, but use quality seed from a reliable source. Nursery hygiene remains critical because contamination can occur during raising, watering or tray handling.

Can I save a tomato plant that has bacterial wilt?

There is no reliable curative treatment for a plant confirmed with bacterial wilt. Early removal and safe disposal are usually more useful than attempting repeated sprays or extra irrigation.

Does mulch prevent bacterial wilt in polyhouse tomato?

Mulch can reduce soil splash and help manage moisture, which may lower some spread risks. It cannot make infested soil disease-free, so it must be combined with drainage, clean water and healthy transplants.

Is grafted tomato fully resistant to bacterial wilt?

No. Suitable rootstocks can reduce losses, but their performance depends on the rootstock, tomato variety and bacterial strain present in that area. Grafting works best as part of an integrated soil and water hygiene programme.

How long should I avoid tomato after bacterial wilt?

The useful break period varies because the pathogen can survive for a long time depending on soil, weeds and climate. Discuss the crop history with your KVK or plant pathologist and use rotation, weed removal and soil treatment rather than relying only on a fixed interval.

ਆਪਣੀ ਕਿੱਟ ਬਣਾਓ