हे कसे काम करतेवेगळे साहित्य खरेदी करा

How to Reduce Condensation in a Polyhouse During Winter

Polyhouse Constructions Agronomy Desk · १३ नोव्हें, २०२६

Condensation forms when warm, moist air inside the polyhouse touches a cold surface, especially the polyfilm roof at night and early morning. Water then collects as droplets and may drip onto leaves, flowers and fruits. To reduce it, ventilate at the right times, irrigate earlier in the day, run air-circulation fans, and use only enough heat to lift the crop and air temperature above the dew point.

A few roof droplets may be unavoidable on very cold nights. The aim is to stop persistent dripping on the crop and long periods of leaf wetness. This is important for tomato, capsicum, cucumber, gerbera, carnation and other winter crops that are prone to botrytis, downy mildew and bacterial diseases in humid conditions.

Understand why winter condensation becomes severe

The air can hold less water vapour as its temperature falls. During a clear winter night, the polyfilm loses heat to the sky and becomes colder than the inside air. If the film temperature falls below the dew point, water vapour turns into droplets on the inner surface.

Several farm conditions make this worse:

  • Late-evening irrigation, especially over-irrigation or leaks.
  • Wet paths, standing water, exposed wet soil and open drain channels.
  • Dense crop canopy with poor air movement near the lower leaves.
  • Side curtains kept shut for too long after sunrise.
  • Foggers or misters operated when the crop does not need cooling.
  • No horizontal air flow, which leaves humid pockets within the canopy.
  • A structure with damaged film, inadequate roof slope, blocked gutters or poor drainage.

Do not judge the risk only by relative humidity (RH). RH commonly rises to 85–95% or more near dawn in winter. What matters is whether leaf, fruit or polyfilm surfaces become cold enough for water to condense. A temperature and RH sensor helps identify the high-risk hours. Install it at crop-canopy height, away from a wet wall, fan discharge or direct sunlight. Read more about placing polyhouse temperature and humidity sensors.

Ventilate early and in short, useful periods

Ventilation is the main tool for taking moisture out. Outside winter air may feel humid, but once it enters the polyhouse and warms up, it can carry more moisture away. This is why a short morning air exchange can sharply reduce indoor humidity.

Naturally ventilated polyhouse routine

For an NVPH, open side curtains gradually after sunrise as soon as outside conditions are safe for the crop. Do not wait until the house feels hot. Morning sunlight warms the air quickly, while trapped moisture remains high.

Use this practical sequence:

  1. Before sunrise: Check crop temperature, outside weather and roof condensation. Keep the house protected during very cold, windy or foggy conditions.
  2. After sunrise: Crack open the leeward-side curtain first. Open the other side and roof vent gradually as solar heat builds.
  3. Mid-morning: Increase opening enough to exchange humid air without creating a cold draft across the crop.
  4. Afternoon: Start reducing openings before the house loses heat rapidly, especially in frost-prone locations.
  5. Night: Close curtains properly, but do not leave irrigation leaks, wet floors or unnecessary water sources inside.

The leeward side is the side away from the wind. Opening it first avoids a strong cold blast on young plants. If side insect nets restrict airflow, curtain opening needs to begin earlier and be maintained longer on suitable days. Well-maintained roll-up curtain gear makes small, repeatable adjustments easier than leaving curtains partly open at random.

Fan-and-pad polyhouse routine

In a fan-and-pad house, cooling pads and foggers are generally not needed for winter humidity control. Operating wet pads adds moisture and can make condensation worse. Keep pad circulation off unless there is a genuine temperature-control need.

Use exhaust fans in brief intervals when indoor humidity is high and outdoor conditions permit. During a cold morning, run the minimum fan capacity needed to remove wet air, then reassess temperature and RH. Long fan operation can chill the crop and waste heat. Ensure shutters open freely and close fully when the fans stop.

Fan capacity, inlet area and pad area must be matched for summer cooling, but winter dehumidification is usually controlled by short, measured ventilation events. See how to calculate exhaust fan size for fan-and-pad polyhouses when reviewing an existing system.

Situation

Best first action

Avoid

Dripping starts before sunrise

Run HAF fans; use limited heat if available

Irrigating or opening fully into freezing wind

RH remains high after sunrise

Gradually open vents or run exhaust briefly

Keeping all curtains closed until noon

Crop is cold and air is humid

Gentle heat plus a small air exchange

Heating without any moisture removal

Wet pads, foggers or misters are running

Stop them unless cooling is essential

Adding moisture to solve a humidity problem

Humidity is high only in crop rows

Improve HAF pattern and canopy management

Assuming roof vents alone will fix it

Use heating with ventilation, not as a standalone fix

A heater can reduce condensation because warmer air can hold more water vapour, and warmer leaves are less likely to reach dew point. But heating alone does not remove water from the polyhouse. If all vents remain closed, the moisture stays inside and RH can rise again when the heater cycles off.

The effective winter method is gentle heat plus controlled ventilation. Raise air and crop temperature modestly, then exchange a small amount of humid air. This is often called a heat-and-vent cycle. It is most useful before dawn, when condensation risk is highest.

For high-value crops in cold belts, use a thermostat or climate controller rather than switching heaters on and off by guesswork. Heater size depends on polyhouse volume, outside minimum temperature, crop set point, film condition, wind exposure and whether an energy screen is used. Refer to winter heating options for vegetable crops before selecting a system.

Follow these safety points:

  • Use properly vented, approved heating equipment.
  • Keep fuel, flame and hot surfaces away from polyfilm, driplines and crop residues.
  • Maintain electrical wiring, earthing and overload protection.
  • Do not use an unvented combustion heater in a closed polyhouse; it can add water vapour and create harmful gases.
  • Check temperature at crop height, not only near the heater.

In many mild Indian winter areas, a few hours of morning venting and continuous circulation may be enough. Heating is more relevant in northern plains during cold waves, plateau areas, hill regions and frost pockets.

Keep air moving through the crop canopy

Horizontal airflow (HAF) fans do not remove water from the air by themselves. Their job is to break up stagnant, humid layers around leaves and move warmer air from the upper part of the house towards the crop. This reduces local condensation and helps leaves dry faster after any unavoidable wetting.

Place fans to create a continuous, slow loop around the house, not a strong jet at one row. Air should travel above or alongside the canopy and return through the other side. Check the far corners, end walls and lower canopy; these are common dead zones.

Run circulation fans continuously or in regular cycles during humid nights and early mornings. The suitable schedule depends on crop stage, house size, temperature and power availability. Feel the crop: leaves should move slightly, not flap hard or feel chilled.

A simple weekly check is useful:

  • Stand at several points at canopy level while the fans run.
  • Look for still, humid zones and for leaves touching each other densely.
  • Listen for fan vibration or slipping belts, where applicable.
  • Clean guards and blades so the fan delivers its expected airflow.

For layout guidance, see how to choose an HAF fan and HAF fan placement for even airflow. Good circulation is especially valuable where side ventilation must stay limited during cold weather.

Change irrigation timing and remove wet surfaces

Irrigation is the most controllable source of moisture inside the house. Water supplied to the root zone is later released through evaporation from soil or growing media and transpiration from the crop. Excess irrigation late in the day raises overnight humidity exactly when the roof cools.

Winter irrigation rules

  • Finish the main irrigation well before late afternoon so the root zone and paths are not wet at night.
  • Use short, measured drip pulses based on crop stage, solar radiation, drainage and media moisture.
  • Inspect drippers, filters, valves and joints for leaks every week.
  • Keep fertigation tanks, flushing water and drain water from adding moisture inside the structure.
  • Do not flood furrows or wet pathways to settle dust.
  • If growing in bags or hydroponic channels, check drain percentage and timing. Excess late drainage raises humidity.

Avoid a fixed irrigation schedule through the year. A cloudy December day needs much less water than a sunny February day, even for the same crop and plant age. Check root-zone moisture or media weight, along with crop appearance, before adding a late irrigation.

Where possible, use mulch or ground cover to reduce direct evaporation from bare soil. Keep drains clear so water leaves the house rather than pooling under the crop. This also reduces insect breeding and root-zone disease risk.

Maintain the roof, drainage and crop canopy

Condensation control starts with daily climate management, but physical maintenance determines whether droplets fall on plants. Inspect the cover and drainage before winter begins.

Check for loose polyfilm, sagging areas, torn patches and dust accumulation. A tight, correctly tensioned roof sheds water better than a slack surface where droplets gather. Clean gutters and check their slope so rainwater does not overflow near sidewalls. A properly fitted 250-micron white diffused polyfilm provides the protected roof surface, but its performance also depends on correct installation, tensioning and upkeep.

Use these crop-management steps as well:

  • Remove lower leaves that touch wet mulch, soil or standing water, according to the crop pruning plan.
  • Maintain recommended plant spacing and timely training to prevent a closed, damp canopy.
  • Remove diseased leaves and fallen plant material promptly.
  • Keep rows, drains and walkways clean and dry.
  • Avoid spraying water-based crop inputs late in the day. If a spray is necessary, choose a period that allows foliage to dry before night and follow label instructions and advice from your KVK or agronomist.

Do not use excessive shade in winter. A dense shade screen can reduce solar warming and slow crop drying. If a screen is needed for a specific crop, open it early enough to allow sunlight and air movement once outdoor conditions improve.

Follow a daily winter condensation checklist

Use this checklist for two weeks when condensation is recurring. Record the time, temperature, RH, irrigation finish time and whether droplets are visible. The pattern will usually reveal the cause.

If RH stays high despite correct irrigation and ventilation, compare inside and outside temperature/RH readings and inspect actual airflow. A sensor may be inaccurate, a curtain may not be opening fully, insect net may be clogged, or the fan pattern may be incomplete. A useful broader guide is how to lower humidity in a polyhouse without stressing crops.

Next steps

Start with the three no-cost changes: stop late irrigation, run circulation fans before dawn, and begin gradual ventilation soon after sunrise. Then repair water leaks, improve drainage and check whether curtains, vents or fans are providing the airflow your crop needs.

For a new house or an equipment upgrade, list the structure dimensions, crop, location and winter minimum temperatures before choosing fans, curtains or film. You can build a material kit and view this week’s item-wise rates for GI structure, polyfilm, nets and fittings. For complex winter climate issues, take your temperature/RH records to your local KVK or protected-cultivation agronomist and adjust the system based on measured conditions.

Frequently asked questions

Is condensation inside a polyhouse harmful to crops?

Occasional droplets on the roof are not always harmful. It becomes a crop problem when water drips onto foliage or flowers, or when leaves remain wet for many hours and disease pressure increases.

Should I keep polyhouse side curtains open at night in winter?

Usually no, because cold air can stress the crop and increase heating needs. Open them only as part of a measured moisture-removal strategy when outside conditions and crop tolerance allow it.

Can anti-drip polyfilm completely stop winter condensation?

Anti-drip behaviour can help water run as a thin film rather than fall as large droplets, but it cannot remove excess humidity. Ventilation, circulation and irrigation management are still necessary.

Why is my polyhouse humid even when I use drip irrigation?

Drip irrigation reduces leaf wetting, but water still evaporates from wet soil or media and is released by plant transpiration. Leaks, excess drainage, dense crop growth and closed curtains can keep humidity high.

Do exhaust fans lower humidity in a fan-and-pad polyhouse during winter?

Yes, exhaust fans can remove moist indoor air when they bring in drier or cooler outside air that can warm up inside. Run them in short, monitored cycles so the crop does not become too cold.

तुमचा किट बनवा