How to Analyse Polyhouse Temperature Humidity Data
Polyhouse Constructions Agronomy Desk · ನವೆಂ 13, 2026
A temperature and humidity logger becomes useful when you stop looking only at the daily maximum and minimum. To analyse polyhouse temperature humidity data, check when a value changed, how long it stayed there, and whether the change matches curtain, fan, pad, fogger or irrigation operation.
A short afternoon heat spike may point to poor ventilation or a power interruption. Several hours of high night-time RH may mean condensation risk, even if the average humidity for the day looks acceptable. Compare each day with outdoor weather, crop stage and your equipment run-time record.
Start with a complete daily climate curve
Download or view a graph with temperature and relative humidity (RH) plotted against time. A 5- to 15-minute logging interval is usually practical for a crop house. An hourly record can hide brief but damaging events, such as a fan trip at 2 pm.
Read one full 24-hour curve before judging a single number:
- Morning: Temperature should rise after sunrise. RH commonly falls as air warms, even when no water has been removed.
- Midday: This is where heat load and cooling performance are tested.
- Late afternoon: Look for a controlled transition as solar radiation falls and cooling equipment reduces.
- Night: Temperature falls and RH rises. The key question is how high RH rises and how long it remains high.
Do not treat RH as a direct measure of water in the air. RH is relative to temperature. For example, when air warms from 20°C to 30°C without any added moisture, its RH can drop sharply. That apparent RH drop does not prove that ventilation or dehumidification removed moisture.
For this reason, always read temperature and RH together. Where the controller provides dew point or VPD, use those values as additional checks. The guide on using VPD for polyhouse climate management explains this next level of interpretation.
Set crop targets before calling a reading good or bad
There is no single ideal temperature and humidity range for every crop. Tomato, capsicum, cucumber, gerbera and nursery crops differ. Targets also change with crop age, light level, fruit load, irrigation, season and local disease pressure.
As a broad working reference, many fruiting vegetable crops are managed around moderate warm days and cooler nights. Day RH is often kept in a middle range, while night RH is allowed to be somewhat higher but should not remain near saturation. Use your crop consultant's target values and compare your log with those values, not with a generic internet number.
The most useful report columns are below.
Measure to review | What it tells you | What needs attention |
|---|---|---|
Daily minimum and maximum temperature | Overall night cooling and day heat load | A maximum that repeatedly exceeds the crop target, or an unexpectedly cold minimum |
Time above the day temperature target | Heat stress exposure | Long periods, especially during flowering and fruit set |
Minimum and maximum RH | Dry-air and wet-air extremes | Very low RH during hot hours or prolonged high RH at night |
Hours above your night RH limit | Moisture and condensation risk | Repeated wet nights, especially with disease-prone crops |
Rate of temperature fall after cooling starts | Cooling response | Slow or no response after fans, pads or vents should operate |
Difference between zones | Climate uniformity | One bay, end wall or side consistently hotter or more humid |
Equipment run time and power status | Whether the system acted as planned | Fans/pump commanded on but no expected climate response |
Rather than relying on one daily average, record duration. An average RH of 78% could hide a safe day with a few humid hours, or a house that stayed at 95% RH for most of the night. These two situations need very different action.
Recognise the four common patterns in logged data
A graph often reveals the fault before you enter the house. The patterns below are starting points, not final diagnoses. Confirm them by inspecting the equipment and crop.
Data pattern | Likely meaning | Checks to make |
|---|---|---|
Temperature rises steeply from late morning and remains high | Heat is entering faster than it can be removed | Side curtains or roof vents open fully, insect net cleanliness, shading, airflow path and power supply |
Temperature has a sharp rise followed by recovery | Temporary cooling or ventilation interruption | Power log, motor overload, controller alarm, pump water level and worker activity |
RH reaches very high values after sunset and stays high until morning | Wet-night and condensation risk | Night ventilation strategy, irrigation timing, standing water, crop density and air circulation |
Temperature drops when fan-and-pad cooling starts, but RH climbs quickly | Evaporative cooling is working but adds moisture | Check crop humidity tolerance, pad operation and need for staged operation or fresh-air exchange |
Repeating up-down temperature swings every few minutes | Controller settings are too close, sensor is poorly placed or equipment is oversized for the stage | Differential/dead band, sensor location and staging sequence |
One sensor is consistently hotter than another | Uneven climate or a bad sensor location | HAF airflow, end-wall conditions, direct sun, roof proximity and calibration |
Heat spikes: look at timing and recovery
A heat spike is not only a high maximum temperature. It is a rapid rise beyond the crop's chosen limit, followed by slow recovery or repeated recurrence. Mark its start time.
- A spike exactly when the cooling system should start may indicate an incorrect controller set point, failed relay, tripped breaker or manual operation delay.
- A spike after a power cut is expected, but the recovery time after power returns is important. Slow recovery can indicate inadequate air movement, poor pad wetting or insufficient ventilation.
- A spike mainly near the leeward end in a naturally ventilated polyhouse can indicate weak cross ventilation, closed curtains, blocked side insect net or unsuitable wind conditions.
- A spike only under one roof section may be caused by torn or missing shade material, a curtain issue or sensor exposure to direct sunlight.
For fan-and-pad houses, the temperature should begin responding after fans and the pad pump operate. It may not instantly reach the set point during hot, humid weather because evaporative cooling is limited by outside humidity. If there is no meaningful change at all, inspect the fan, pad wetting, water supply and air path. Also review whether fan capacity and pad area have been matched; see how to match cooling pad area with exhaust fans.
Read wet nights as a disease-warning signal
At night, plant transpiration reduces while temperature falls. RH rises because cooler air holds less moisture. If leaf surfaces cool to the dew point, condensation can form even if the sensor does not show exactly 100% RH.
Repeated high RH for several night hours favours many foliar disease problems. It can also affect pollen release and crop transpiration. Check the crop early in the morning for droplets on leaves, flowers, wires and plastic. These observations give context to the logger graph.
When the log shows wet nights, work through this checklist:
- Check irrigation finishing time. Avoid leaving the root zone and house excessively wet close to sunset unless crop demand requires it.
- Look for water sources. Repair leaking drippers, wet floor patches, drain overflow, algae-filled channels and pad water leaks.
- Check crop density. Dense, unpruned foliage slows drying within the canopy even when the central sensor looks acceptable.
- Confirm air movement. HAF fans should mix air without blowing harshly on one crop row. Review HAF fan placement for even airflow if different zones behave differently.
- Use ventilation carefully. A small amount of night ventilation can remove moisture when outside air is drier in absolute terms. But cold outside air can chill the crop. Watch both temperature and RH after every change.
- Inspect the roof and film. Dripping condensation from the cover can create local wetness. Winter conditions need a separate approach; refer to how to reduce condensation in a polyhouse during winter.
Do not react by opening vents fully every night. The correct action depends on outside temperature, outside moisture, wind, crop stage and the risk of chilling. Trial a small controlled change, then compare the next three to five nights of data.
Use equipment behaviour to diagnose the cause
Add equipment status to the same graph wherever possible: exhaust fan stages, pad pump, foggers, HAF fans, curtains, roof vents and power supply. A climate graph without equipment status tells you what happened; the combined graph helps show why it happened.
Naturally ventilated polyhouse
In an NVPH, temperature usually follows solar radiation and outside air more closely. A slow midday rise can be normal on a still summer day. But a large gap between inside and outside temperature, particularly when curtains should be fully open, calls for inspection.
Look for blocked side insect nets, curtains not opening to their intended height, damaged roll-up gear, crops or stored material blocking the side path, and internal shade practices that reduce light but restrict air movement. Details of the house design matter; compare systems through NVPH vs fan and pad.
Fan-and-pad polyhouse
A healthy fan-and-pad graph often shows a noticeable temperature fall when cooling starts and a simultaneous RH rise. The amount of cooling varies with the outdoor wet-bulb condition, pad condition, fan capacity and air leakage.
Warning signs include:
- Fans recorded as on but temperature does not fall.
- Pad pump is on but RH does not rise at all and the pad appears dry.
- A very humid inlet side and a hot exhaust side, suggesting uneven airflow or inadequate fan performance.
- Cooling that works in the morning but weakens later, suggesting water heating, reduced flow, clogged pads, pump trouble or fan performance loss.
Use the data to decide what to inspect, then inspect physically. The article on cellulose cooling pad maintenance can help build a regular check routine.
Check whether the logger is telling the truth
Poor sensor placement can create a false problem or hide a real one. A sensor near the roof, pad, exhaust fan, fogger, wet wall, side opening or direct sun will not represent the crop canopy.
Place the main sensor around crop canopy height, shielded from direct radiation and away from direct water spray. Use more than one sensor in larger houses or where you suspect an inlet-to-exhaust difference. See where to place temperature and humidity sensors in a polyhouse for location guidance.
Suspect the sensor or logger when you see:
- The same value for many hours despite clear weather changes.
- Sudden impossible jumps that immediately return to normal.
- RH fixed at 99% or 100% for long periods without any visible wetness.
- One sensor differing persistently from nearby sensors with no physical reason.
- Temperature high only at the sensor during sunny hours, suggesting radiation heating.
Clean the sensor according to its manual, protect it from spray and compare it periodically with a known good instrument. Calibration matters, particularly for RH sensors, which can drift in wet and dusty conditions. Do not alter controller settings until you are confident the measurement is sound.
Follow a weekly data-review routine
A 15-minute review each week is more useful than discovering a seasonal problem after yield falls. Keep a simple sheet for each compartment or zone.
- Download the previous seven days of temperature, RH and equipment run-time data.
- Mark the daily maximum temperature, hours above target, minimum RH, maximum RH and hours above the night RH limit.
- Circle days with unusual outdoor weather, power cuts, irrigation changes, harvest activity or equipment repair.
- Compare the hottest day and most humid night with the same crop zone from the previous week.
- Walk the house at the time shown by the graph. For example, inspect at 1 pm after a heat spike and before sunrise after a wet night.
- Change one controllable item at a time: curtain timing, fan stage, irrigation finish time or HAF schedule.
- Review the next few days before making another major change.
Keep notes on crop observations as well: leaf curl, flower drop, condensation, disease hotspots and uneven growth. Climate numbers matter because they explain what the crop experienced.
Next steps
Start by choosing one representative week and identify the hottest 30 minutes, the most humid three hours and the longest equipment run. Visit the house at those times over the next few days to confirm what the data suggests.
If the issue is uneven climate, first verify sensor placement and airflow before spending on new equipment. If a replacement or upgrade is needed, you can buy individual polyhouse items or use the kit builder with live weekly rates to review required materials and quantities.
Frequently asked questions
What logging interval is best for polyhouse temperature and humidity data?
A 5- to 15-minute interval is suitable for most polyhouses because it captures fan cycling, fogging and short heat spikes. Use a shorter interval only when troubleshooting a fast-changing cooling or controller problem, as it creates more data to review.
Why does relative humidity fall sharply at noon even when I have not ventilated the house?
RH falls naturally when air temperature rises because warm air can hold more water vapour. Check temperature, dew point or VPD before deciding that the crop has become too dry or that ventilation caused the change.
Is 100% RH on a logger always a sensor fault?
No. It can occur near saturation at night, around a wet cooling pad or when condensation is likely. However, a sensor held at 100% for days without visible moisture should be cleaned, checked for placement problems and compared with another instrument.
How can I tell from data whether a fan-and-pad system is underperforming?
Check whether temperature starts falling after the fans and pad pump are commanded on, and whether this response becomes weaker later in the day. Confirm the pattern by inspecting pad wetting, water flow, fan operation, power supply and the air path through the house.
Should I use average daily humidity to manage disease risk?
No. Daily average RH can hide several hours of very humid night conditions that encourage condensation and disease. Track the duration above your crop's night RH limit and inspect the canopy early in the morning.
