Polyhouse Fogger Line Spacing: A Practical Layout Checklist

Polyhouse Constructions Agronomy Desk · ನವೆಂ 13, 2026

Fogger lines in a polyhouse are usually placed 3–4 m apart, with fogger nozzles generally 1.5–2.5 m apart on each line. Treat this as a starting layout, not a fixed rule.

For an even fog cloud, mount nozzles about 0.6–1.2 m above the mature crop canopy. Closer line spacing is usually needed for short crops, dense canopies, weak air movement or low mounting heights. Wider spacing may work only when the nozzle manufacturer confirms a larger coverage pattern and the fog mixes evenly without wetting leaves.

First, distinguish line spacing from nozzle spacing

Two dimensions decide how evenly fog reaches the crop:

  • Fogger line spacing: Distance between two parallel lateral lines across the width of the polyhouse.
  • Nozzle spacing: Distance between fogger nozzles on the same lateral line.

A common mistake is to use wide line spacing because the fog seems to travel far when the house is empty. Once tomato, cucumber, capsicum or flowers have a full canopy, the crop blocks air movement. The fog cloud may then remain above the plants or leave dry strips between lines.

Also check whether your device is a true fogger or a low-pressure mister. A true fogging system produces very fine droplets that should evaporate quickly. A mister produces bigger droplets and needs more cautious spacing and shorter run time to avoid wet foliage. See this comparison of foggers and misters for polyhouse cooling before finalising the system.

Use these starting spacings by crop canopy and mounting height

The table below gives practical starting ranges for a well-filtered fogging system. Test these ranges in your own polyhouse before installing every line permanently.

Crop situation

Typical mature canopy height

Suggested nozzle mounting height above canopy

Starting line spacing

Starting nozzle spacing on line

Nursery plants, leafy greens, low beds

0.3–1.0 m

0.8–1.2 m

2.5–3.0 m

1.2–1.8 m

Strawberry, gerbera, low flower crops

0.4–1.0 m

0.8–1.5 m

2.5–3.5 m

1.5–2.0 m

Capsicum, tomato and cucumber before full height

1.0–1.8 m

0.8–1.2 m

3.0–3.5 m

1.5–2.0 m

Mature indeterminate tomato, cucumber or tall cut flowers

2.0–3.0 m

0.8–1.2 m

3.0–4.0 m

1.5–2.5 m

Open plant density with strong horizontal air movement

Varies

0.8–1.2 m

3.5–4.5 m after testing

2.0–3.0 m after testing

Do not automatically use the widest range for a tall crop. A tall canopy often needs more, not less, attention to fog distribution because leaves obstruct the fog cloud. If the crop has two dense rows under each trellis bay, a 3 m line spacing can perform better than 4 m even in a high-roof polyhouse.

Match spacing to nozzle flow, coverage pattern and height

Nozzle flow rate matters, but it does not by itself tell you the right physical spacing. Two nozzles with the same flow can have different droplet sizes and plume patterns. Use the nozzle supplier’s data sheet for:

  • flow in litres per hour at the recommended operating pressure;
  • fog plume or coverage diameter at your planned mounting height;
  • droplet size range;
  • required filtration level;
  • minimum and maximum working pressure.

Start with nozzle centres at around 60–80% of the stated effective coverage diameter. This creates overlap between adjacent fog clouds. For example, if a nozzle gives an effective 3 m fog pattern at the selected height, a nozzle spacing of about 1.8–2.4 m is a sensible field-testing range.

Mounting height changes the pattern considerably:

  • Too low: fog remains concentrated beneath the line, producing wet strips and dry gaps.
  • Too high: fog can collect near the roof, be carried to vents, or condense on the polyfilm before it reaches the crop.
  • Best position: normally 0.6–1.2 m above the final canopy, with enough clearance from crop wires, trellis supports and the roof.

Avoid directing fog at the polyfilm, shade screen, circulation fan or side insect net. Moisture on these surfaces can drip, raise disease risk and reduce cooling efficiency.

For a correct nozzle choice before layout, refer to how to size fogger nozzles for a polyhouse.

Calculate the number of lines, nozzles and water demand

Do the basic layout calculation before buying laterals, nozzles and a pump. Use the cultivated internal length and width, not only the nominal structure size. Keep pathways, fan bays, pad walls and service areas in mind.

The three essential calculations

  1. Number of fogger lines

Polyhouse width ÷ proposed line spacing

Round to a whole number and adjust the actual spacing slightly so the outer lines are equally placed from both side walls.

  1. Nozzles per line

Polyhouse length ÷ proposed nozzle spacing

Again, round appropriately and keep the first and last nozzles at similar distances from the end walls.

  1. Total fogging flow

Total number of nozzles × flow per nozzle

This is the pump flow requirement when the entire zone runs together. The pump must also maintain the pressure specified for every nozzle, after allowing for pipe friction, filters, valves and height difference.

Worked example

Consider a 30 m wide × 48 m long polyhouse. You select 3 m line spacing and 2 m nozzle spacing, after a canopy and airflow assessment.

  • Lines across width: 30 ÷ 3 = 10 lines
  • Nozzles on each 48 m line: 48 ÷ 2 = 24 nozzles
  • Total nozzles: 10 × 24 = 240 nozzles

If each nozzle delivers 1.5 litres per hour at its correct pressure:

  • Full-system flow: 240 × 1.5 = 360 litres per hour
  • Area covered: 30 × 48 = 1,440 m²
  • Maximum water application while continuously running: 360 ÷ 1,440 = 0.25 litres/m²/hour

In actual operation, foggers normally run in short cycles rather than continuously. Therefore, the average water added over an hour will be much lower than the continuous-flow figure. The right cycle depends on outside temperature, RH, ventilation, crop stage and whether leaves are staying dry.

If one pump cannot deliver the required flow and pressure uniformly, divide the house into hydraulic zones. Do not simply add more nozzles to a line and hope for equal output at the far end. Uneven pressure causes uneven fogging.

Read pump selection for foggers and cooling pads when deciding zone size, pump pressure and pump flow.

Lay out the grid correctly inside the polyhouse

A symmetrical grid gives more uniform coverage than lines pushed close to one side. For the 30 m × 48 m example above:

  • Place the first and last fogger lines about 1.5 m from the side walls.
  • Place the remaining lines at 3 m intervals.
  • Put the first and last nozzle about 1 m from each end wall.
  • Keep 2 m spacing between the remaining nozzles.

This “half-spacing at the edge” approach prevents a dry band along the perimeter. However, adjust the layout around structural columns, crop rows, fans, lights, gutters and access paths.

Special adjustments for fan-and-pad houses

In a fan-and-pad polyhouse, airflow moves from the cooling-pad end towards the exhaust fans. Fog can drift in that direction. A uniform rectangular grid is still the starting point, but check whether the crop near the fans dries faster than the crop near the pad.

Do not use fogging as a replacement for correctly sized pads and exhaust fans. First ensure that pad area and fan capacity are balanced. The guide on matching cooling pad area with exhaust fans explains this relationship.

For naturally ventilated polyhouses, wind direction and open curtain position can change fog movement from hour to hour. Use shorter fog cycles and rely on field observation, especially during hot, dry afternoons.

Installation checklist before commissioning

Use this checklist while placing fogger lines and before planting a full crop.

  1. Mark mature canopy height, not seedling height. The fogging line should remain above the final crop canopy.
  2. Use equal edge offsets from both side walls and both end walls where possible.
  3. Keep lines level as far as possible. Sagging laterals can collect water and affect output.
  4. Support laterals securely at suitable intervals so that nozzle direction does not change when the pipe expands or vibrates.
  5. Install isolation valves for zones so one area can be checked or serviced without stopping the whole house.
  6. Provide proper filtration before the fogging lines. Fine fogger orifices clog easily from sand, algae, iron deposits and suspended matter.
  7. Add flush ends to every lateral. Flush the lines before fitting nozzles and periodically during operation.
  8. Use pressure gauges at the pump outlet and, ideally, near the far end of a representative line. A major pressure difference signals a design or blockage issue.
  9. Keep electrical equipment dry. Do not locate nozzles where fog directly enters motors, control panels or sensors.
  10. Check drainage and roof condensation. Water should not drip onto foliage, flowers or fruit.

Water quality decides whether the chosen spacing remains effective over time. A partially blocked nozzle may look functional but deliver a weak, coarse spray, creating dry areas. Plan filtration and cleaning from day one with this guide to water filtration for foggers and cooling pads.

Test the layout with the crop present

The best time to judge a fogger layout is not on installation day in an empty structure. Test it after the crop has developed enough leaf area to affect airflow.

Run one short cycle during the hottest expected operating period and walk the house after a few minutes. Check three zones separately:

  • near side walls and end walls;
  • below the centre of each fogger line;
  • halfway between two lines and halfway between two nozzles.

You want a uniform, quickly dispersing fog cloud. Leaves should not remain visibly wet after each cycle. If droplets settle on the crop, first reduce run time or improve cycle control. If wetting remains only under the lines, the nozzles may be too low, too close, too high-flow, or producing oversized droplets.

If the middle areas stay drier than the areas under lines, reduce line spacing or nozzle spacing. If fog reaches one side of the house but not the other, review HAF fan direction, side ventilation and nozzle orientation before adding more nozzles.

Place temperature and humidity sensors at crop level, away from direct fog streams and away from walls. Guidance on placing temperature and humidity sensors in a polyhouse can help you compare conditions across the house.

Operate foggers without creating a disease problem

Fogging raises RH and can provide useful evaporative cooling in hot, dry conditions. But excessive RH reduces plant transpiration, slows drying and increases the chance of foliar disease. The risk is especially high during monsoon weather, cloudy days, early morning and evening.

Use foggers only when the crop needs cooling or humidity support. Avoid routine continuous operation. Review crop-level temperature, RH, leaf dryness and ventilation together rather than operating only by clock time.

As a practical rule:

  • Increase ventilation when humidity is already high.
  • Reduce or stop fogging if leaves, flowers or fruits stay wet.
  • Avoid fogging close to sunset unless there is a specific crop-management reason and sufficient drying time.
  • Reassess spacing when crop height, trellis density or ventilation arrangement changes.

The ideal climate varies by crop and stage. For deeper guidance, see using VPD to manage polyhouse climate.

Next steps

Start with a 3–4 m fogger line grid and 1.5–2.5 m nozzle spacing only after checking the manufacturer’s nozzle pattern, flow and operating pressure. Set the lines 0.6–1.2 m above the mature canopy, use equal edge spacing, calculate total system flow, and test the layout with a real crop in place.

Before purchasing pipe, filters, pumps and fittings, prepare a simple drawing showing polyhouse dimensions, crop rows, mature canopy height, fogger zones and equipment locations. If you are planning the wider protected-cultivation structure and material list, you can build a material kit and view this week’s rates.

Frequently asked questions

Should fogger lines run along the length or width of a polyhouse?

Either direction can work if the grid remains uniform and the laterals are properly supported. In fan-and-pad houses, lines are often arranged to suit the structural bays and airflow direction, but nozzle output should be checked at both the pad and fan ends.

How far above tomato or cucumber plants should foggers be installed?

Keep foggers around 0.6–1.2 m above the expected mature canopy, not above the young crop. This allows fog to mix before reaching leaves while keeping the nozzle low enough for useful coverage.

Can I increase nozzle spacing to reduce the number of foggers?

Only after a distribution test confirms that the spaces between nozzles remain adequately covered. Wider spacing can create dry strips and often leads to longer run times, which may wet plants directly below each nozzle.

Why are leaves wet directly under my fogger line?

The usual causes are oversized droplets, excess run time, low nozzle mounting, high nozzle flow or poor pressure control. Check filters and nozzle condition as well, because a partly blocked fogger can change its spray pattern.

Do foggers need to run during monsoon in an naturally ventilated polyhouse?

Often they are needed less because outside air already carries substantial humidity. Use crop-level temperature and humidity observations rather than a fixed schedule, and prioritise ventilation if foliage is slow to dry.

ನಿಮ್ಮ ಕಿಟ್ ತಯಾರಿಸಿ