When to Use an Internal Shade Screen for Polyhouse Crops
Polyhouse Constructions Agronomy Desk · 13 नव॰ 2026
An internal shade screen for polyhouse is best used when you need flexible shading close to the crop canopy: during harsh afternoon sun, sensitive growth stages, or in only one crop zone. It gives more precise light control than a roof-level shade net. However, because sunlight has already passed through the polyfilm before reaching an internal screen, it usually does less to lower the total heat load of the structure.
If your main problem is very high summer temperature across the whole polyhouse, start with ventilation, roof-level/external shading and, where relevant, evaporative cooling. Use an internal screen when crop protection and light management matter more than maximum heat rejection.
Internal screen versus roof-level shade net
A roof-level shade net sits over or at the roof zone and reduces sunlight before it heats the air, crop and surfaces inside. An internal screen is fixed or movable below the polyfilm, usually above the crop or gutter height. It intercepts direct radiation after it enters the polyhouse.
This difference matters most from March to June in much of peninsular and central India, and later in north India as summer develops. At noon, the internal screen can prevent leaf scorch and reduce direct radiation on fruit, but heat can still collect in the roof space above it.
Point | Internal shade screen | Roof-level or external shade net |
|---|---|---|
Best purpose | Adjustable crop-level light control | Reducing whole-structure solar heat gain |
Where it stops sunlight | Below the polyfilm, inside the crop space | Before or at the roof covering |
Peak heat reduction | Moderate; depends on ventilation above and below screen | Usually better, because heat is rejected earlier |
Control by crop stage | Strong, especially with retractable screens | Usually uniform across the house |
Zoning different crops | Possible in separate bays or blocks | Difficult unless separate structures are used |
Effect in cloudy weather | Can be opened to preserve useful light | Fixed nets may continue to cut light |
Management need | Higher: opening, closing, cleaning and checking airflow | Lower if fixed, though seasonal fitting/removal is needed |
Main risk | Trapped warm, humid air above or below a poorly managed screen | Excess shade for the crop through the season |
For a basic naturally ventilated polyhouse, roof-level shade is often the simpler summer solution. For a high-value crop where light changes through the day or season, an internal movable screen can be worth considering.
Use an internal screen in these situations
Choose an internal screen when at least two or three of the following conditions apply.
1. Your crop is getting direct-light injury, not just hot air
Internal shading is particularly helpful when leaves bleach, tender shoots wilt in direct sun, flower petals mark, or fruit develops sunscald on the exposed side. These symptoms should be checked carefully: poor irrigation, salinity, root disease and mites can also cause wilting or leaf damage.
Crops with tender foliage or valuable flowers can benefit from a short period of shading around intense midday radiation. In fruiting vegetables such as capsicum, tomato and cucumber, the need depends on variety, canopy density, fruit exposure, planting date and local climate. Do not keep a screen closed all day simply because outside temperatures are high.
2. You need shade only for part of the day
A retractable internal screen is useful where mornings and late afternoons provide productive light, but the period around noon is too intense. It can be opened in lower-light conditions, during cloudy weather, and as days shorten after the monsoon.
This is an important advantage over a fixed roof shade net. A fixed net may protect the crop in May but can reduce photosynthesis and crop vigour in cloudy monsoon weeks or winter.
3. Crops or crop stages differ within the same structure
An internal screen can be planned in bays or sections when one part of the polyhouse has young transplants, flowering plants or shade-tolerant crops, while another section has an established fruiting crop. It is not a substitute for proper compartment design, but it gives useful flexibility.
For example, a nursery block may need more protection than a mature vegetable block. Keep enough clearance between the screen and crop canopy so that workers can operate, air can move and foliage does not touch the material.
4. Your crop needs light management through the season
In areas with strong pre-monsoon sun but lower monsoon radiation, seasonal flexibility is valuable. Internal screens are also useful where growers want to control light during transplant establishment or temporary heat events without permanently reducing roof light.
Monitor crop response instead of following a calendar alone. Compare shaded and unshaded rows for leaf temperature, internode length, flower retention, fruit set and colour. Too much shade can make plants soft, elongated and less productive.
5. You operate a fan-and-pad polyhouse with controlled equipment
A properly designed fan-and-pad house can use internal screens more effectively than a poorly ventilated structure because airflow can be managed. Yet the screen must not obstruct the path from cooling pads to exhaust fans. Air needs a clear route over and through the crop.
Review the overall cooling layout before adding a screen. The relationship between pad area and fan capacity is as important as the screen itself; see how to match cooling pad area with exhaust fans. Use circulation fans where needed to reduce hot pockets below the screen.
When roof-level shade is the better choice
Use roof-level or external shade net first when the entire polyhouse is overheating in summer. This applies especially when the structure has limited roof ventilation, side curtains remain closed for rain or insect exclusion, or power failures affect active cooling.
External shading intercepts radiation before it enters through the polyfilm. It can therefore reduce heating of the roof air layer, structural members, crop surfaces and floor. This is why it is generally more effective for whole-house summer cooling.
Roof-level shading is often a better choice in these cases:
- The crop is uniformly stressed across the whole house from high daytime temperature.
- You grow one crop with a similar light requirement throughout the area.
- You have a naturally ventilated polyhouse and do not want another internal layer that can slow upward air movement.
- You need a simple, seasonal measure rather than daily screen operation.
- Labour or automation for opening and closing an internal screen is not available.
The right shade percentage varies by crop, place, season and existing covering. A net that is suitable in dry, hot Maharashtra may cut too much light during a humid, cloudy monsoon period. Read the practical considerations in summer shade net percentage for polyhouse crops before selecting a shade level.
Check ventilation before installing an internal screen
The most common mistake is treating the screen only as a light-control material. It also changes airflow, heat movement and humidity around the crop.
In a naturally ventilated polyhouse, warm air normally rises towards the roof and leaves through open vents. A screen across the bay can slow this upward movement. If hot air is trapped above the screen, the roof zone becomes much hotter. If moist air stays under the screen in the evening or early morning, condensation and disease risk can rise.
Use this checklist before installation:
- Measure temperature above and below the proposed screen level. Take readings at crop height and near the roof on clear afternoons for several days.
- Check side and roof vent operation. Curtains and roof vents must open sufficiently when conditions allow. Repair gears, insect net tears and stuck vent mechanisms first.
- Assess air movement at canopy height. Stagnant corners, dense crop rows and long bays may need air circulation fans.
- Allow for screen gaps and layout. Do not block fans, pad-to-fan airflow paths, roof vents, gutters, electrical lines or maintenance access.
- Plan opening times. A movable screen should normally be open during low light, and managed before humidity climbs in the evening.
- Install sensors at crop level. Track temperature and relative humidity below the screen, not only at one point near the controller. See guidance on where to place temperature and humidity sensors.
For fan-and-pad houses, screen permeability and the airflow route need technical attention. A dense screen across the full width can increase resistance and reduce uniform cooling. If you are still deciding between house types, compare the operating requirements in NVPH vs fan and pad.
Select the screen type and layout around the crop need
The term “shade screen” covers different materials. The choice should be based on shade level, reflectivity, porosity, durability and whether the screen is fixed or retractable.
Fixed internal screens
A fixed screen costs less in moving parts and is suitable where a crop needs similar shade for much of its production cycle. Its weakness is lack of flexibility. It continues to reduce light on cloudy days and in winter unless removed.
Fixed screens suit a limited area such as a nursery corner better than an entire production house with changing seasonal conditions.
Retractable internal screens
A retractable screen is more suitable for variable Indian conditions. It can be deployed during intense sun and opened when light is valuable. Manual systems can work in smaller blocks if staff follow a clear routine. Larger commercial houses benefit from motorised operation linked to light, temperature and wind/rain logic, with manual override.
Automation does not remove the need for crop observation. A light threshold that works in April may not suit July, and a closed screen during a humid spell can create avoidable disease pressure.
Reflective versus dark shade materials
Reflective materials can reduce radiant heat load better than dark materials at a similar shade level, depending on construction and placement. Darker nets absorb more heat, which can then radiate into the space if placed internally. White or reflective screens generally give more diffuse light distribution than a dark screen, though actual performance varies by product specification.
Check the stated shade factor, width, UV stabilisation and intended use. A product marketed for outdoor roof shading may not be the right material or mounting arrangement for an internal retractable system. Review available shade-net and other material options along with the technical data sheet before finalising the layout.
Operate the screen without losing yield
A good screen programme balances lower leaf stress with enough daily light for photosynthesis. The aim is not to make the inside feel cool at any cost; it is to keep the crop productive and healthy.
Start conservatively. On bright days, close the screen for the most intense period, then observe the crop for one to two weeks. If leaves remain hot and stressed despite adequate irrigation and ventilation, expand the shading period or improve roof-level heat rejection. If plants stretch, flowering reduces or fruit colour is poor, you may be over-shading.
Pay special attention to these periods:
- Morning: Open early enough to capture useful radiation, particularly in winter and cloudy weather.
- Peak afternoon: Deploy where direct radiation causes leaf or fruit injury, but maintain side ventilation or active cooling.
- Evening: Open the screen before late-day humidity builds up, unless a separate night thermal-screen plan has been designed.
- Monsoon: Use only when light is genuinely excessive. Long closure in humid weather can keep foliage wet for longer.
- Winter: Internal shade is usually needed less. Crops often need maximum light, though specific flower crops and unusually bright days can be exceptions.
Maintain uniform irrigation and nutrition while evaluating shade. A screen may reduce plant water demand somewhat, but do not make large irrigation cuts without checking media moisture, drainage and crop uptake.
Common mistakes to avoid
Do not install an internal screen to cover up a weak climate system. If daytime temperature is excessive because vents are undersized, roof vents are not opening, or fan-and-pad equipment is poorly matched, solve those causes first.
Avoid these errors:
- Using a fixed dense screen all year in a vegetable polyhouse.
- Closing the screen on a humid evening and leaving it closed overnight without a thermal-screen strategy.
- Hanging it too low, where it blocks work, spray coverage or crop airflow.
- Fitting a full-width screen without checking fan, pad and roof-vent airflow.
- Judging success only by air temperature rather than crop condition, humidity and yield quality.
- Buying material only by shade percentage, without checking width, reflectivity, UV life and mounting requirements.
An internal screen and an external screen can also be used together, but only for a crop and climate plan that justifies the combined light reduction. During extreme heat, this combination may protect a sensitive crop temporarily. During low-radiation periods, it can severely restrict growth.
Next steps
First, identify whether your problem is direct-light injury at crop level or excessive heat across the whole polyhouse. Take temperature and humidity readings above and below the intended screen position for a few clear days, and inspect crop symptoms row by row.
If heat is the whole-house issue, assess roof-level shading, ventilation and cooling first. If crop-level light control is the issue, plan a movable internal screen with adequate clearance and an operating schedule. You can build a material kit and see this week’s live item rates for the required structure, covering and net components. For large or complex layouts, get the screen support, airflow route and crop zones reviewed before material dispatch.
Frequently asked questions
Can I use an internal shade screen in a naturally ventilated polyhouse?
Yes, but it needs more care than in a fan-and-pad house. Keep ventilation paths open and watch for heat collecting above the screen and humidity building below it, especially during monsoon or in the evening.
Does an internal shade screen cool a polyhouse as much as an external net?
Usually no. An external or roof-level net blocks part of the sun before it passes through the polyfilm, so it normally reduces total heat gain more effectively. An internal screen is stronger for adjustable crop-level shading.
Should the internal screen stay closed throughout the summer day?
Not usually. Opening it in the morning and later afternoon preserves useful light, while closing it mainly during intense sunshine can protect the crop. The correct timing varies with crop, cloud cover, season and local weather.
Will an internal screen increase humidity around the crop?
It can if it reduces upward ventilation or is kept closed when humidity is already rising. Measure relative humidity at crop level and open the screen in time to support air exchange and leaf drying.
Which crops benefit most from internal shading in a polyhouse?
Crops with tender foliage, exposed fruit, sensitive flowers or young transplants can benefit during high-radiation periods. The decision should be based on observed crop stress and light requirement, not crop name alone.
