આ કેવી રીતે કામ કરે છેઅલગ સામગ્રી ખરીદો

GI Pipe Size for Polyhouse: Columns, Arches, Purlins and Bracing

Polyhouse Constructions Agronomy Desk · 13 નવે, 2026

The right GI pipe size for polyhouse depends on what that pipe must carry. Columns, arches and foundation-connected members take the main structural load. Purlins support the cover and tie the frame together. Bracing controls sideways movement in wind.

So, do not compare two polyhouse quotations only by total GI weight or by one advertised pipe diameter. Ask for a member-wise schedule showing the outer diameter (OD), wall thickness, spacing, grade, galvanising and where each pipe is used. The final selection must be made against the span, gutter height, bay spacing, wind zone, rainfall, crop system and site conditions.

Start with diameter, thickness and the pipe's job

A GI pipe is normally described by two separate dimensions:

  • Outer diameter (OD): The outside width of the tube, usually in mm. A larger OD generally gives greater resistance to bending.
  • Wall thickness: The thickness of steel in the tube wall, in mm. A thicker wall improves strength, screw-holding and resistance to denting or buckling.

A 48 mm OD pipe with a 2 mm wall is not the same as a 48 mm OD pipe with a 1.6 mm wall. Both may look similar from a distance, but their steel content and structural performance differ.

Pipe duty also matters. A pipe used as a vertical column sees compression and bending. An arch sees bending, uplift and cover load. A purlin spans between arches. A diagonal brace mainly resists racking, which is the tendency of a frame to become a parallelogram under wind force.

For this reason, one-size-fits-all claims should be treated carefully. The same pipe size that works on a small, sheltered nethouse may be unsuitable for a wide multi-span polyhouse in a high-wind or high-rainfall location.

Typical GI pipe sizes by polyhouse member

The table below is a practical guide to the relative sizes commonly seen in Indian protected-cultivation frames. It is not a substitute for an engineer's drawing or approved bill of materials. Actual specifications vary by structure type and local design load.

Frame member

Main role

Common indicative OD range

Common indicative wall-thickness range

When a heavier section is often needed

Foundation stub / embedded support

Transfers load to concrete foundation

48–76 mm

about 2.0–3.2 mm

High wind, tall structure, wider span, weak soil or larger bays

Main column

Carries roof and wind loads to foundation

48–76 mm

about 2.0–3.2 mm

Greater gutter height, multi-span blocks, coastal or exposed sites

Main arch / rafter

Forms roof profile and supports roof system

48–76 mm

about 2.0–3.0 mm

Wide span, gothic roof, heavy rainfall or higher wind design

Truss members / internal roof ties

Reduces bending in main frame

32–48 mm

about 1.6–2.5 mm

Long bays, wide spans and fan & pad structures

Purlins

Join arches and support film-fixing system

32–48 mm

about 1.6–2.0 mm

Larger purlin spacing, exposed roofs or extra crop-support loads

Diagonal wind bracing

Stops frame sway and racking

25–42 mm

about 1.6–2.0 mm

High-wind sites, end bays and long multi-span structures

Side-wall rails / curtain supports

Supports insect net, curtain and side framing

32–48 mm

about 1.6–2.0 mm

Tall side curtains, wider curtain openings or motorised systems

Door and end-wall frame

Holds doors, nets and end cladding

32–48 mm

about 1.6–2.0 mm

Large double doors or exposed end walls

These are OD ranges, not nominal plumbing-pipe sizes. Suppliers may also describe tubes in inches, such as 1.5 inch, 2 inch or 2.5 inch. Always request the actual OD and thickness in mm. This prevents confusion between nominal trade sizes and measured dimensions.

Why columns need larger and thicker GI pipes

Columns are the load path from the roof to the foundation. They must take vertical roof load, wind pressure, wind suction and forces transferred through the arch or truss connection.

For a smaller naturally ventilated polyhouse on a protected site, columns may use a moderate structural tube size. But a higher gutter, a wide span or a long multi-span block increases leverage on the columns. In such cases, diameter and wall thickness may both need to increase.

Pay close attention to these areas:

Column base and foundation connection

The bottom portion is vulnerable because it is close to soil splash, standing water and fertiliser-bearing runoff. The steel section must match the foundation design, anchor arrangement and expected uplift. A good pipe cannot compensate for shallow or poorly cured concrete.

Read the guide on polyhouse foundation types before finalising the frame. Foundation depth and size should be based on soil and structural requirements, not copied blindly from another farm.

Gutter-side columns in multi-span houses

In a multi-span structure, gutter-side columns carry forces from adjoining roof slopes and gutters. They can have a more demanding job than simple side-wall supports. Do not assume that every vertical pipe in the structure should be identical.

Tall side walls

A taller gutter height improves working space and can assist air movement, but it also creates a longer unsupported column. The member size, bracing layout and bay spacing must be considered together. See how height decisions interact with the frame in this guide to selecting polyhouse gutter height.

Main arches: diameter is only part of the design

An arch pipe gives the polyhouse its roof shape. It supports polyfilm, crop-support arrangements where included, purlins and wind loads. It must retain its designed curve after bending and after years of service.

Main arches are often larger than purlins and braces. Wide-span houses commonly require a larger-diameter arch, a thicker wall, closer arch spacing, trussing, or a combination of these measures. Raising only one parameter is not always enough.

The roof profile has an effect too:

  • Gothic arches shed rain effectively and have a sharper roof profile.
  • Quonset or rounded arches have a continuous curved form.
  • Gable and saw-tooth forms use different rafter, truss and connection arrangements.

A pipe that bends cleanly is not automatically adequate structurally. Over-bending, flattening at the bend or visible wrinkles can weaken the section. Check that the arch curvature is uniform from one bay to the next and that connections are aligned.

Wind suction is especially important on roof edges, corners and end bays. In an open field, a storm can try to lift the cover and roof frame. For this reason, the arch specification must be read along with anchors, purlins, film fixing and bracing. Learn more about how wind load changes polyhouse structure design.

Purlins use lighter pipes, but they are not optional

Purlins run lengthwise along the roof. They connect successive arches, maintain their spacing and provide support to the roof system. Since purlins usually have a shorter and different load path than main arches, they can often use a smaller OD or thinner wall.

That does not mean they can be selected casually. Purlins may bend if their spacing is too wide, their wall is too light, or a worker steps on them during film work. Weak purlins can also allow the roof shape to distort, causing loose film, water pockets and uneven stress at clips.

When reviewing a drawing, ask:

  1. How many purlin lines are provided on each roof slope?
  2. What is the OD and wall thickness of each purlin?
  3. How are purlins fixed to arches: clamps, bolts, welded tabs or another approved connection?
  4. Are purlins continuous or joined at bays? If joined, where are the joints located?
  5. Does the design change at the end bays, ridge and gutter zones?

The roof cover should be fixed to a stable frame. A 250-micron white diffused polyfilm still needs correctly spaced structural members, proper profiles and secure fastening to perform well.

Bracing pipes prevent sway in wind

Bracing is commonly the smallest-looking structural member, but it does a critical job. Diagonal braces form triangles between columns, arches or roof members. A triangle resists shape change far better than a rectangle without a diagonal.

Bracing may be found in:

  • Side walls, especially at end bays
  • Roof planes
  • End walls
  • Longitudinal bays of multi-span houses
  • Corners and locations near doors

Braces commonly use lighter pipe than columns and arches because their main job is tension and compression along their length. Yet their connection details are equally important. A brace with loose bolts, poor welds or weak clamps cannot transfer force properly.

Never remove a diagonal brace to create a tractor path, packing area or wider doorway without a revised structural solution. If a door opening is needed, it should be framed with suitable headers, posts and replacement bracing. For a clearer view of layouts, read polyhouse bracing types and their structural role.

How structure type and site change pipe selection

GI pipe size cannot be selected from area alone. A 1,000 m² structure in two different places may need different member schedules.

Naturally ventilated polyhouse

An NVPH has side openings, insect net and often ridge ventilation. The frame must hold the roof cover and also manage wind entering through ventilated openings. Curtain and net supports need adequate stiffness, particularly where the side opening is tall.

Fan & pad polyhouse

Fan & pad structures include equipment openings, cooling-pad walls, exhaust-fan frames and tighter environmental-control requirements. End-wall framing may need specific reinforcement around these openings. Compare the operating concepts in NVPH versus fan & pad polyhouse.

Nethouse

A nethouse does not carry polyfilm in the same way, but shade net catches wind. A loosely tensioned or poorly fixed net can put repeated load on the frame. Do not assume that a nethouse automatically needs very light pipe.

High-rainfall, coastal, hilly and exposed sites

Rainfall can create water load where roof drainage is poor. Coastal humidity and salts speed up corrosion. Hilly farms may have uneven ground and wind exposure. In these conditions, engineering, galvanising quality, foundation design and drainage all deserve extra attention.

What to verify before you approve the GI material

Use this checklist before placing an order or accepting material at the site.

  1. Obtain a member-wise schedule. It should state OD, wall thickness, quantity, length and intended use for columns, arches, purlins, bracing and end walls.
  2. Match the schedule to the drawing. Count bays, arches, purlin rows, braces, doors and gutter supports. Do not accept an unexplained reduction in members.
  3. Measure samples. Use a vernier caliper for OD and a suitable tube-thickness gauge for wall thickness. Measure more than one pipe from each size lot.
  4. Check pipe marking and documents. Confirm the manufacturer, steel specification, galvanising details and test certificates. Brand name alone does not replace a written specification.
  5. Inspect coating and cut edges. Look for bare steel, deep scratches, peeling or damage from bending and drilling. Cut ends and site modifications need suitable corrosion protection.
  6. Examine bends and joints. Arches should not be flattened at bends. Bolt holes should be clean and correctly aligned. Welded areas should be properly protected against corrosion.
  7. Check fittings separately. Clamps, bolts, base plates, film profiles and anchors must match the specified load path. A heavy pipe joined with weak fittings is still a weak system.
  8. Keep the paperwork. Drawings, bills of materials, invoices and test certificates help during maintenance, insurance and subsidy documentation where applicable.

Polyhouse Constructions supplies complete material kits and individual items, with ISI-marked branded GI steel and technical documentation. You can build a kit and view the current item quantities or review individual protected-cultivation materials before comparing specifications.

Next steps

First, decide the structure type, crop, span, height and site exposure. Then ask for a structural drawing and a member-wise GI pipe schedule rather than requesting only a “standard polyhouse pipe.” Compare OD, wall thickness, arch spacing, bracing and foundation details as one system.

Finally, inspect the delivered pipes before erection and retain the technical documents. This approach helps you choose a frame that is appropriate for your farm, rather than paying for steel in the wrong places or discovering weaknesses after the cover is installed.

Frequently asked questions

Which GI pipe size is best for a polyhouse?

There is no single best size for every polyhouse. Main columns and arches commonly use larger, thicker tubes than purlins and braces, but the correct selection depends on span, height, wind, rainfall, bay spacing and structure type.

Is a thicker GI pipe always better for a polyhouse?

A thicker wall generally improves the member’s capacity and durability, but it must be paired with the right diameter, spacing, bracing and foundation. Adding thickness to one member cannot correct poor overall frame design.

How can I tell if a supplier has used thinner GI pipe than promised?

Ask for a written OD and wall-thickness schedule, then check sample pipes with measuring tools before erection. Also verify the manufacturer’s marking, invoices and test certificates for the supplied material.

Do polyhouse arches and columns use the same GI pipe?

They may use the same size in some small designs, but they perform different structural jobs. Taller houses, wider spans and multi-span structures often require different pipe sections or additional truss members and bracing.

Does a coastal farm need a different GI pipe specification?

Often, yes. Salt-laden air and high humidity increase corrosion risk, so coating quality, protection of cut edges, drainage and maintenance become especially important. An engineer should also assess the local wind exposure before finalising the frame.

તમારી કિટ બનાવો