આ કેવી રીતે કામ કરે છેઅલગ સામગ્રી ખરીદો

Biocontrol Agents for Polyhouse Pests: A Practical Guide

Polyhouse Constructions Agronomy Desk · 12 નવે, 2026

Biocontrol agents for polyhouse pests are living organisms that suppress insects and mites without relying only on chemical sprays. They include predators that eat pests, parasitoids that develop inside a host pest, and microbial products that infect the target pest. Their biggest strength is prevention and early control. They are usually too slow to rescue a severe, crop-wide outbreak on their own.

For tomato, cucumber, capsicum, flowers and nursery crops, start by scouting before visible damage becomes widespread. Then choose an agent that matches the pest, crop stage and polyhouse conditions. Keep pest numbers low through insect exclusion, clean planting material, sanitation and careful spray choices.

The three main types of biocontrol agents

A biological control programme has to match the agent to the pest. One beneficial does not control every pest. Also, species availability can differ between suppliers and regions in India, so confirm the target pest named on the product or release guidance.

Predators: beneficials that feed on pests

Predators actively search for and consume prey. They can feed on eggs, larvae, nymphs or adults depending on the species.

Common examples include:

  • Predatory mites such as Phytoseiulus species for red spider mites, and Amblyseius or Neoseiulus species for thrips and, in some programmes, mites.
  • Lacewing larvae (Chrysoperla species), which can feed on aphids, whiteflies, small caterpillars and other soft-bodied pests. Their usefulness depends on correct release timing and survival after release.
  • Minute pirate bugs such as Orius species, which are important predators of thrips where commercially available.
  • Ladybird beetles, which can feed heavily on aphids. They may disperse from a crop unless pest colonies are present and the structure is well managed.

Predators need prey to establish. Releasing them into a completely pest-free house may not be economical unless the supplier recommends a preventive programme with an alternative food source.

Parasitoids: beneficials that use the pest as a host

Parasitoids are tiny wasps that lay eggs in or on a particular pest stage. The developing young kill that host. They are generally more pest-specific than predators.

Examples include:

  • Encarsia and Eretmocerus species for greenhouse whitefly and tobacco whitefly, depending on the species and local programme.
  • Aphidius species for aphids.
  • Diglyphus species for leaf miner larvae.

Parasitoids often leave visible signs. For example, parasitised whitefly nymphs may become darker or show a round exit hole after the adult parasitoid emerges. Learn to recognise these signs before deciding that control has failed.

Microbial biocontrols: organisms that infect pests

Microbial biocontrols are applied as formulations, much like a crop-protection spray, but they contain beneficial microbes or their active biological components.

  • Bacillus thuringiensis (Bt) targets young caterpillar larvae after they feed on treated foliage. It does not control sucking pests such as whiteflies, aphids or mites.
  • Entomopathogenic fungi such as Beauveria, Metarhizium and Lecanicillium can infect certain whiteflies, aphids, thrips and other insect pests, subject to the product label.
  • Entomopathogenic nematodes can target some soil-dwelling or concealed insect stages in suitable moist media or soil situations.

Microbial products need good coverage and suitable temperature, humidity and water quality. They are not interchangeable: always use a registered product only for its labelled crop and target pest, following label instructions and advice from your KVK or crop advisor.

Match the agent to the pest, not just the crop

Correct identification comes before buying or releasing anything. Whiteflies, aphids, thrips and mites can all produce curling, yellowing and poor plant growth, but need different agents. Use a hand lens to inspect leaf undersides, young terminals and flowers.

Main pest

Useful biological options

Best use stage

Key condition for success

Whitefly

Encarsia/Eretmocerus parasitoids; selected fungal biocontrols

At first nymphs or low adult catches

Stop fresh entry through side openings and remove virus-infected plants promptly

Thrips

Predatory mites; Orius where available; selected fungal products

Preventive or at first flower infestation

Regular flower inspection, moderate heat stress and compatible sprays

Red spider mite

Phytoseiulus and other predatory mites

First hotspots, before webbing spreads

Avoid dusty, hot, water-stressed crop conditions; target hotspots quickly

Aphid

Aphidius parasitoids, lacewings, ladybirds and fungal biocontrols

Small colonies before leaf curl becomes severe

Control ants, which protect aphid colonies and disturb natural enemies

Leaf miner

Diglyphus parasitoids

Early mines, before widespread leaf damage

Keep spray residues low and remove heavily mined leaves carefully

Caterpillars

Bt and other label-approved microbial options

Very young larvae

Thorough coverage and repeated monitoring; large larvae are harder to control

For detailed pest-specific action, see this guide on whitefly control in polyhouses and the practical steps for red spider mite signs and control.

Conditions biocontrol agents need to work

Protected cultivation gives a major advantage: you can manage the crop environment and reduce pest entry. But a polyhouse can also become unfavourable for beneficials if it gets too hot, too dry, or heavily disturbed by incompatible sprays.

Start with a low pest population

Biocontrol is most reliable at low to moderate pest pressure. A few whiteflies per plant, an early aphid colony, or a small mite hotspot can often be managed through a planned release and close monitoring. A dense whitefly population across the house, heavy mite webbing, or widespread thrips damage needs immediate corrective action guided by a qualified agronomist; biologicals may then be part of recovery, not the only answer.

Scout at least once a week, and two or more times weekly during hot weather, flowering and crop transitions. Record the pest, plant location, life stage, damage and beneficials seen. This weekly polyhouse pest scouting guide can help set up a repeatable route.

Maintain suitable temperature and humidity

Each agent has its preferred conditions. In broad terms, excessive heat inside a naturally ventilated polyhouse during April–June can reduce survival of delicate predatory mites and parasitoids. Very low humidity may also reduce performance of some fungal microbial products. On the other hand, prolonged wet foliage and very high humidity can increase crop disease risk.

Aim for the crop's appropriate climate rather than creating humidity only for a microbial spray. Ventilate at the right time, reduce heat stress, and use air circulation where needed. In fan-and-pad systems, ensure uniform airflow; in naturally ventilated structures, maintain side ventilation without compromising insect exclusion. Read more about managing humidity to reduce polyhouse diseases, because disease control and biocontrol must work together.

Prevent continuous pest reinvasion

Beneficials cannot keep up if new pests enter every day. Check doors, curtain gaps, torn side net, joints around pipes, drainage openings and unprotected vents. Use a double-door or entry discipline where possible, and avoid bringing infested trays, crates or weeds into the house.

A correctly selected and well-maintained side insect net reduces entry of flying pests. Mesh selection is a balance: finer exclusion improves pest control but can restrict airflow, increasing heat and humidity. This is why net choice must suit the crop, local summer conditions and ventilation design.

Avoid harming the beneficials after release

Broad-spectrum pesticide residues are one of the most common reasons for poor biocontrol. A spray applied before release can remain harmful for days or longer, depending on its active ingredient, dose, formulation and environment. Some products may also affect eggs or immature stages that are hard to see.

Before any chemical treatment:

  1. Tell the advisor or dealer which predator, parasitoid or microbial agent is already in the crop.
  2. Check compatibility information from the biological supplier and the pesticide label.
  3. Treat only identified hotspots when possible, rather than spraying the full polyhouse.
  4. Follow the stated waiting period before introducing or reintroducing beneficials.
  5. Keep a record of date, block, product, target pest and release date.

Do not assume that a product described as “soft” or “natural” is harmless to all beneficial insects. Compatibility is species-specific.

A practical release and application plan

Biocontrol succeeds through routine, not one-time releases. The supplier's recommendation should take priority because release rates vary with crop, pest level, agent formulation, pack size, climate and whether the programme is preventive or curative.

Use this field checklist.

  1. Inspect incoming seedlings. Reject or isolate trays with whiteflies, mites, aphids, leaf mines or virus-like symptoms. Do not introduce pests before the first release.
  2. Clean the crop area. Remove weeds inside and around the structure, old crop debris and heavily infested leaves. Dispose of infested waste safely away from the crop.
  3. Map pest hotspots. Divide a 1,000 m² house into manageable blocks. Mark hotspots on a simple drawing rather than releasing evenly without observation.
  4. Release at the correct time. Place parasitoid cards or predator carrier material in the crop canopy as instructed. Keep packs out of direct sun, never leave them in a hot vehicle, and release soon after delivery.
  5. Distribute evenly, then strengthen hotspots. Preventive releases may be spread throughout the house. Mite or aphid hotspots often need focused releases, if advised.
  6. Apply microbial products with coverage in mind. Target leaf undersides, tender growth, flowers or pest hiding sites as the label indicates. Use clean equipment and avoid mixing unless label compatibility is clear.
  7. Recheck after release. Inspect the same marked plants in about 3–7 days, then weekly. Look for live pests, new damage, predator presence, parasitised hosts and spread beyond the hotspot.

Sticky traps are useful monitoring tools, but they do not replace plant inspection. Place them so they do not trap large numbers of released flying parasitoids near release points. See how sticky trap colour and placement should fit into monitoring.

Integrate biologicals into an IPM programme

Biological control is one layer of integrated pest management (IPM). The most stable programme combines exclusion, monitoring, cultural control and compatible interventions.

  • Exclusion: Repair insect net and close curtains correctly, especially at dawn and late afternoon when flying pests can enter.
  • Crop hygiene: Remove diseased or virus-suspect plants early. Virus-infected plants remain a source for vectors such as whitefly and aphids.
  • Irrigation and nutrition: Avoid excessive nitrogen, which can encourage soft, attractive growth for aphids and whiteflies. Avoid plant water stress, which worsens mite problems.
  • Targeted intervention: Spot-manage a growing hotspot before it spreads. Use only crop- and pest-appropriate products, with biological compatibility checked.
  • Records: Compare trap counts, pest incidence and beneficial activity block by block. These records help decide whether the next crop needs an earlier preventive release.

For a season-long framework, use this article on how to build an IPM plan for a polyhouse crop cycle.

Common reasons a biocontrol programme fails

A failed release is not always a poor-quality agent. Usually, one or more management conditions were missing.

Problem seen

Likely reason

Corrective action

Pest rises rapidly after release

Release started too late or pest entered continuously

Reduce entry points, identify hotspots and seek advisor-led corrective action before restarting biologicals

Beneficials are not visible

They may be tiny, nocturnal or still in immature stages; or spray residue caused losses

Use a hand lens, check host signs and review spray history and compatibility

Mites spread despite predator release

Heat, dust, water stress or severe initial mite load

Reduce crop stress, remove heavily infested leaves and reinforce only under supplier guidance

Microbial spray gives weak results

Poor leaf coverage, unsuitable weather, old product or incorrect target pest stage

Check label, storage, spray coverage, water quality and pest life stage

Whitefly remains high near doors

Constant adult entry from outside

Improve entry discipline, repair net/curtain gaps and manage weeds around the structure

Next steps

First, identify the main pest and its life stage using weekly scouting. Then select a biological agent specifically meant for that pest, arrange delivery so it can be released promptly, and check compatibility with every spray planned in the previous and coming weeks.

If pest entry is recurring, inspect the structure before spending more on releases. For upgrades or repairs, Polyhouse Constructions lists protected-cultivation materials and specifications in its individual materials section. A sound IPM programme gives predators, parasitoids and microbial biocontrols the time and conditions they need to work.

Frequently asked questions

Can I use biocontrol agents and chemical pesticides in the same polyhouse?

Yes, but only after checking the specific pesticide's compatibility with the beneficial species being used. Spray residues can kill or weaken beneficials, so follow the label and the biological supplier's waiting-period guidance.

Which biocontrol agent is best for whitefly in a polyhouse?

Parasitoids such as Encarsia or Eretmocerus are commonly used, while some microbial fungal products may also be suitable. The right option depends on the whitefly species, crop, temperature and whether the infestation is still low.

How soon do beneficial insects start controlling pests?

Predators may begin feeding soon after release, but visible population reduction commonly takes time. Parasitoids need time to locate hosts, develop and produce the next generation, so early releases and weekly checks are important.

Do biological controls work during the hot Indian summer?

They can work, but extreme heat and dry conditions reduce the performance of several beneficials. Lower crop heat stress, avoid harsh spray residues and choose an agent with guidance suited to local conditions.

Are microbial biopesticides safe for predatory mites and parasitoids?

Some can be compatible, but this is not automatic. Formulation, application timing, target pest and the released beneficial species all matter, so verify compatibility before application.

તમારી કિટ બનાવો