How it worksBuy individual items

What Zinc Coating Is Needed for Polyhouse GI Pipes?

Polyhouse Constructions Agronomy Desk · 13 Nov 2026

A polyhouse frame stays strong only when its steel stays protected from rust. For the main columns, arches, trusses and bracing, ask for hot-dip galvanised GI pipe with at least 360 GSM zinc coating, unless your approved structural design specifies a higher level. In coastal belts, very humid locations, acidic soil or areas with corrosive industrial air, do not select coating weight alone: ask for a corrosion-focused design and stronger detailing.

The important point is simple: “GI” is not a complete specification. The supplier should state the zinc coating mass in GSM, the steel pipe standard, pipe thickness, and whether pipe ends, cuts and welds are protected.

What zinc coating means on a GI pipe

Galvanising applies zinc over steel. Zinc acts as a barrier between steel and moisture. It also provides sacrificial protection: when a small scratch exposes steel, nearby zinc corrodes first and slows rusting of the steel.

The coating is normally expressed as GSM, meaning grams of zinc per square metre of pipe surface. In specifications, it is generally the total coating mass over the relevant surface area, but you should confirm the test method and whether the stated value refers to both sides or a particular surface. Do not compare two quoted GSM values unless they use the same standard and measurement method.

A heavier zinc coating usually gives a longer corrosion allowance. It does not make a thin pipe structurally stronger. Pipe wall thickness, diameter, steel grade, span, wind load, bracing and foundations must all be designed separately.

For a protected cultivation structure, zinc protection matters because the frame faces several moisture sources:

  • Rainwater and roof condensation
  • Humid air around side curtains and ridge vents
  • Fertiliser salts and spray drift
  • Wet soil around embedded or splash-zone portions of columns
  • Water trapped at joints, gutters, clamps and pipe ends
  • Salt-laden air in coastal districts

The practical coating choice for Indian polyhouses

For a typical naturally ventilated polyhouse on an inland site with proper drainage, 360 GSM hot-dip galvanising is a sound buying benchmark for primary GI members. It is commonly sought for durable protected-cultivation frames because it provides materially better corrosion resistance than light commercial galvanising.

This is a decision guide, not a substitute for a structural drawing. The final requirement can change with the site, design life, member location and state or project tender specification.

Site or component

Practical zinc-coating decision

Why it matters

Inland site with moderate rainfall and good drainage

At least 360 GSM hot-dip galvanised coating for primary frame

Suitable benchmark for long-term frame exposure when detailing is good

High-rainfall or persistently humid area

360 GSM minimum, with better drainage and careful joint detailing

Moisture remains on steel for longer periods

Coastal or salt-air location

Seek higher corrosion protection than a basic inland specification; use a site-specific design

Chlorides can rapidly attack zinc and exposed steel

Columns near soil, splash or standing water

Higher protection and sound foundation/drainage details

These are often the first locations to corrode

Secondary members, clips and fittings

Specify compatible galvanised/coated hardware

A durable pipe can still fail at a poorly protected connection

Cut ends and field-welded areas

Protect after fabrication as per approved procedure

Zinc is damaged or absent at exposed steel surfaces

A lower coating mass may be seen in pre-galvanised tube and light fabrication. It can be acceptable for certain secondary, dry components only when the engineer has specified it. It should not be quietly substituted for the main frame merely because it looks shiny when new.

At the other extreme, a heavier coating is not a free pass. A frame with thick zinc but poor drainage, open pipe ends, unsealed welds and water-holding clamps can still rust early.

Hot-dip galvanised versus pre-galvanised pipe

The zinc coating method is as important as the quoted GSM.

Hot-dip galvanised pipe

In hot-dip galvanising, fabricated steel or pipe is immersed in molten zinc. This can provide a robust, continuous coating, including around external surfaces and, depending on the process, internal surfaces. It is generally the preferred choice for exposed primary polyhouse members.

For a frame made from individual pipes, confirm whether galvanising was done before or after fabrication. If pipes are cut, drilled or welded after galvanising, those operations create locations that need approved touch-up protection. A fabricated frame hot-dip galvanised after welding can offer strong protection, but its suitability depends on fabrication design, vent holes, drainage holes and process control.

Pre-galvanised pipe

Pre-galvanised steel is coated first and then formed into tube. It can be economical and neat for some uses. But cut edges, weld seams and fabrication damage need close attention. Coating weights can also be lower than what a primary outdoor agricultural frame requires.

The answer is not that every pre-galvanised product is poor. The answer is that the buyer must match it to the member and the exposure. For main columns and arches, do not accept a vague promise of “GI quality”. Ask for the actual coating designation and test evidence.

For a fuller explanation of these two options, read pre-galvanised versus hot-dip pipe for polyhouses.

Why corrosion exposure changes the requirement

A polyhouse is not fully sheltered from weather. Its crop-friendly environment can be hard on steel.

Coastal and saline locations

Sea air deposits salts on the frame. Salt attracts moisture and raises corrosion risk, including in sheltered corners where rain does not wash deposits away. Coastal farms should obtain a design that considers local distance from the sea, prevailing wind, humidity and maintenance access. More zinc may help, but connection details and regular washing of salt deposits are equally important.

See the specific design considerations for coastal humidity and salt air.

High-rainfall and humid regions

Monsoon moisture can remain on gutters, roof joints and the lower section of columns. If the site has slow drainage, water splashes mud and dissolved salts onto the base of the frame. Select proper foundations, maintain runoff paths and avoid allowing irrigation water to strike columns.

Fertiliser and chemical exposure

Fertilisers and spray solutions can be corrosive, especially when residues remain wet on steel. Never use the structural frame as a place to mix inputs, hang leaking lines or store fertiliser bags. Keep fertigation leaks under control. For crop-protection products, follow the label instructions and guidance from your KVK or agronomist.

Trapped water at connections

Tight clamps, overlapping members, gutter supports and closed pipe ends can hold water. This causes local corrosion even where the rest of the structure looks fine. Good fabrication must allow drainage and avoid pockets that stay wet.

How to specify the GI pipe on your purchase order

Put the coating requirement in writing before payment. It avoids a dispute after the material reaches the farm.

Use this buying checklist:

  1. State the application. Write whether the pipe is for main columns, arches, trusses, bracing, purlins, nethouse members or accessories.
  2. Specify coating mass. For primary polyhouse members on a normal inland site, state “hot-dip galvanised, minimum 360 GSM zinc coating” or the value in your approved drawing.
  3. Name the relevant pipe standard. Ask for the applicable BIS/ISI standard and pipe grade, rather than accepting only a trade description.
  4. List diameter and wall thickness separately. A heavier zinc layer cannot compensate for a pipe that is too thin for wind and crop load.
  5. Ask how cuts and welds are treated. Obtain the approved method for protecting exposed steel after field fabrication.
  6. Include fittings. Bolts, clamps, base plates, brackets and gutter supports should have compatible corrosion protection.
  7. Ask for records. Request technical data sheets, lab test certificates and dispatch documents showing the material supplied.
  8. Check the site condition. Mention coast, industrial pollution, black-cotton soil, high rainfall, standing water or saline irrigation water before design finalisation.

A proper quote should not say only “GI structure”. It should make comparison possible across suppliers.

How to inspect the coating when material arrives

Visual inspection helps, but it cannot confirm GSM by itself. Zinc can look bright even when the coating is lighter than required.

Check these points at delivery:

  • Match pipe sizes, thicknesses and coating specification against the approved bill of materials.
  • Look for bare steel, flaking zinc, deep scratches, red rust, rough uncoated patches and crushed pipe ends.
  • Inspect welds, drilled holes, cut ends and joints closely.
  • Ensure pipes are stored above wet ground and covered without trapping condensation.
  • Check manufacturer markings and certificates against the invoice and dispatch list.
  • If the project is large or the site is corrosive, arrange independent coating-thickness or coating-mass verification using the relevant standard test method.

Do not reject a coating merely because it has a dull or matte-grey appearance. Hot-dip galvanised surfaces can vary in appearance due to steel chemistry and cooling conditions. Reject it when documents, measurements or visible defects show that it does not meet the agreed specification.

Pipe thickness inspection is another essential step; use this guide on checking GI pipe thickness.

Frame life depends on more than zinc coating

Zinc coating is a major part of frame durability, but it works with the rest of the design. A long-life frame needs adequate member sizes, wind bracing, correct anchors, drainage and maintenance.

Pay particular attention to the lowest 300–600 mm of columns, depending on foundation detail and local splash conditions. Keep soil, mulch and organic debris from staying against steel. Repair damaged protective areas promptly according to the approved procedure. Once red rust appears at a joint, inspect nearby hidden surfaces instead of treating it as only a cosmetic spot.

Strong wind can flex a weak frame, crack coatings at damaged joints and loosen fasteners. Choose structural members based on wind zone and local exposure, not coating alone. The guide to how wind load changes polyhouse structure design explains why this must be decided before material ordering.

For routine checks after installation, follow an annual polyhouse structure maintenance checklist.

Next steps

First, classify your site as normal inland, high-rainfall/humid, or coastal/corrosive. Then get a structural drawing that lists pipe diameter, wall thickness, zinc coating mass and connection protection for every key member.

For a normal inland primary frame, use minimum 360 GSM hot-dip galvanised GI pipe as your starting specification. Do not reduce it without a written engineering reason. Polyhouse Constructions supplies ISI-marked branded steel from Tata, Jindal and JSW, with technical data sheets and lab test certificates supplied at dispatch. You can build a material kit and view current item rates or compare individual polyhouse materials before finalising your requirement.

Frequently asked questions

Is 120 GSM zinc coating enough for a polyhouse GI pipe?

It may be seen in lighter pre-galvanised material, but it is generally not the preferred benchmark for exposed primary polyhouse members. For a normal inland main frame, specify at least 360 GSM hot-dip galvanising unless the approved structural design says otherwise.

Does a higher GSM zinc coating make a GI pipe stronger?

No. Zinc coating improves corrosion resistance, while strength comes from the pipe diameter, wall thickness, steel grade and structural design. Both must be checked independently before buying.

Which areas of a polyhouse frame rust first?

Column bases, cut pipe ends, welded zones, clamps, gutter supports and places where water remains trapped usually rust first. Fertiliser residue, saline air and poor drainage speed up this damage.

Can I paint GI pipes to improve protection?

Painting can be part of a repair or additional protection system, but the surface preparation and paint compatibility must be correct. Do not use ordinary paint as a substitute for the specified galvanising on a new primary frame.

How can I verify the zinc coating claimed by a supplier?

Ask for the pipe specification, galvanising certificate and relevant test report with the dispatch documents. For large, subsidised or corrosive-site projects, independent verification by an appropriate test method gives stronger assurance than visual inspection alone.

Build your kit