How it worksBuy individual items

Thermic Polyfilm for Polyhouse: Is It Worth Using?

Polyhouse Constructions Agronomy Desk · 13 Nov 2026

Thermic polyfilm for polyhouse is worth considering when your crop faces repeated cold nights during the production season. It can hold some of the heat stored in soil, plants and structure after sunset, helping reduce night-time temperature drops. Its value is highest for high-value crops in cold or elevated regions, and lower in warm areas where night temperatures rarely limit crop growth.

The important point is simple: thermic film does not create heat. It slows one route of heat loss. Before paying extra for it, assess your local minimum temperature, crop season, crop value, and how well your polyhouse is sealed and managed.

What is thermic polyfilm and how does it work?

A thermic polyfilm is a greenhouse covering made with additives that reduce the escape of long-wave infrared (IR) radiation. During the day, soil, crop beds, water and the structure absorb solar energy. After sunset, these surfaces release stored heat as infrared radiation.

Ordinary polyethylene film allows more of this long-wave radiation to pass out. Thermic film is designed to reflect or retain a greater share within the polyhouse. This can make the inside temperature fall more slowly through the night.

It is often called an IR film, thermal film or heat-retention film. It may also be offered with other properties, such as UV stabilisation, diffusion and anti-drip treatment. These are separate properties. Do not assume that every white, diffused or UV-stabilised film is automatically thermic.

A thermic cover generally helps most during clear, calm nights. On cloudy nights, cloud cover itself reduces radiative heat loss, so the difference may be smaller. Strong wind, open curtains, gaps around doors, or poorly fitted film can also reduce the benefit sharply.

How much difference can it make at night?

In suitable conditions, a thermic film may keep the polyhouse modestly warmer than a standard comparable film during the night. The actual difference is variable, often more noticeable before dawn, when crop stress is greatest.

Do not plan your crop around one fixed temperature gain. The result changes with:

  • Outside minimum temperature and duration of the cold spell
  • Clear sky versus cloudy sky
  • Wind speed and air leakage from side curtains, doors and vents
  • Polyhouse size, height and exposed surface area
  • Soil moisture, crop canopy and thermal mass inside
  • Whether the house is naturally ventilated or fan-and-pad controlled
  • Film condition, fitting tension and overlap sealing

A well-managed naturally ventilated polyhouse can benefit from thermic film in winter. However, if side curtains remain open because humidity is high, the stored heat escapes with the outgoing air. In that situation, disease management and ventilation may matter more than the film itself.

Thermic film also cannot replace heating where temperatures stay far below the crop’s safe range for many hours. In severe cold, it can reduce heat demand but is not a full heating system.

When thermic polyfilm is worth the extra cost

The decision should be based on avoided crop loss or improved crop timing, not only on whether the film gives a warmer reading at night.

It is usually a stronger option in the following situations:

Cold belts, hills and winter production

In Maharashtra hill areas, parts of Karnataka, Telangana, Madhya Pradesh, Rajasthan, north Indian plains during winter, and Himalayan or north-eastern locations, winter nights can restrict crop growth. The exact need varies greatly even within one district because elevation, valley location and cold-air drainage differ.

If your crop is planted for winter harvest and local night temperatures commonly approach its stress range, thermic film deserves serious evaluation.

High-value, temperature-sensitive crops

Capsicum, cucumber, tomato, gerbera and other protected-cultivation crops may be affected when nights become too cold. Symptoms can include slow growth, delayed picking, weak fruit set, misshapen fruit or reduced quality, depending on the crop and stage.

For a crop with good market value, even a small improvement in early yield, continuity of harvest or quality may justify a higher-cost covering. This is more relevant when the crop is at flowering, fruit set or an early establishment stage during cold weather.

Farms targeting early or late market windows

A farmer selling during a period of limited local supply may benefit more from stable winter growth than a farmer harvesting at the same time as peak market arrivals. First calculate whether earlier or more regular harvests have a realistic market advantage in your mandi, organised retail channel or buyer contract.

Structures that are already well managed

Thermic polyfilm gives better value when the basics are right: properly tensioned cover, sealed end walls, functional curtains, good drainage, healthy crop roots and a practical humidity plan. It is not a correction for weak structure design or poor crop management.

When standard polyfilm may be the better choice

A standard UV-stabilised, diffused cover may be the practical choice if cold nights are occasional and not a major production constraint. It may also be better when the main challenge is excess heat, humidity or low winter light rather than cold.

Farm situation

Likely decision on thermic film

Why

Warm coastal or tropical location with mild nights

Usually not essential

Night heat retention may have limited crop value; humidity control can be the bigger need.

Mild winter area, short vegetable crop

Compare carefully

A small night benefit may not recover the additional investment within one crop cycle.

Cold winter nights and sensitive crop at flowering

Often worth evaluating

Better night conditions may support crop continuity and fruit set.

Frost-prone site

Useful, but not enough alone

It may reduce radiative cooling but cannot guarantee frost protection during severe events.

Heated fan-and-pad polyhouse

Potentially useful

It can reduce night heat loss and possibly heating requirement, subject to engineering and operating conditions.

Poorly sealed NVPH with open curtains at night

Fix basics first

Air exchange can remove the retained heat quickly.

For most Indian naturally ventilated polyhouses, the decision should not be only “thermic versus non-thermic.” Consider the complete covering specification: thickness, UV stabilisation, light diffusion, anti-drip requirement, film width, expected service life and suitability for your crop calendar.

For example, diffused light can improve light distribution through the canopy, while anti-drip properties can help reduce droplets falling from the roof. Read more about the trade-off in diffused polyfilm versus clear film and when anti-drip polyfilm is useful.

Thermic film versus other ways to manage cold nights

Thermic polyfilm is only one tool. A farm may achieve a better result by combining it with low-cost operational measures.

Tighten and inspect the cover

Loose film flaps in wind and can tear near clips. More importantly, gaps near end walls, gutters, door frames and curtain edges let warm air escape. Check cover tension before winter and repair holes early. See the practical points in this guide on how to prevent polyfilm tearing at clips.

Manage curtains according to temperature and humidity

Closing side curtains before the evening temperature falls can retain more warmth. But fully closing a house for long periods can raise relative humidity and condensation. This increases disease risk, especially in dense crop canopies.

Use local observation. Check inside temperature and humidity near crop level, not only at the entrance. Open strategically in the morning to remove humid air once outside conditions permit. Keep insect net clean, because blocked airflow makes this balance harder.

Use thermal mass where practical

Moist soil stores more heat than very dry soil, though over-irrigation is not the answer. Irrigation scheduling must follow root-zone need and humidity conditions. Water-filled containers or other thermal-mass approaches may help in small units, but their benefit depends on volume and layout. Do not expect a few drums to protect a large commercial polyhouse in a cold spell.

Consider an inner cover or thermal screen for severe winters

An internal thermal screen or a low tunnel over crop rows can reduce heat loss further than roof film alone. These methods need careful design because they can reduce light and restrict air movement. For high-value crops in genuinely cold locations, compare these options with the cost of supplemental heating.

A practical checklist before ordering thermic polyfilm

Use one winter season of site records if possible. A low-cost minimum-maximum thermometer or data logger helps turn a vague concern into a clear purchase decision.

  1. Record outside and inside minimum temperatures. Track at least the coldest part of the season, especially just before sunrise.
  2. Identify the crop-sensitive period. Note whether transplant establishment, flowering, fruit set or fruit development coincides with cold nights.
  3. List actual losses. Separate cold-related issues from poor drainage, nutrient imbalance, pests, low light and high humidity.
  4. Inspect heat leaks. Check side curtain overlap, door sealing, ridge openings, damaged film and end-wall joints.
  5. Ask for the complete technical data sheet. Confirm the film is specifically thermic or IR-retentive. Also verify micron thickness, UV stabilisation, diffusion, anti-drip treatment and warranty terms.
  6. Compare like with like. Do not compare a thermic 200-micron film with a non-thermic 250-micron film and assume the price difference is only for thermic performance.
  7. Estimate the payback from crop value. Consider improved grade, avoided loss, earlier picking or lower heating use. Be conservative; market prices and yields vary by season.
  8. Plan humidity management. Decide who will operate curtains and monitor condensation on cold mornings.

Film thickness still matters for durability and handling. Review how to choose polyhouse film thickness in microns before finalising a specification.

Questions to ask a supplier

Ask for a written specification, not only a verbal claim that a film is “winter grade” or “thermal.” A good specification should clearly state the film’s intended properties.

Ask these questions:

  • Is the film thermic/IR-retentive, and what is the stated performance standard?
  • Is it white diffused, clear, or another light-transmission type?
  • Does it have anti-drip treatment, and is that needed for my crop?
  • What are the micron thickness, roll width and warranty conditions?
  • Is the film suitable for my roof profile and local wind conditions?
  • What installation method protects the film at clips, channels and sharp edges?
  • Is a lab test certificate or technical data sheet available with dispatch?

Polyhouse Constructions provides technical data sheets for its products and lab test certificates with dispatch. If you are comparing material combinations for a new structure or replacement cover, you can build a kit and view the current item-wise rate before finalising the specification. Live rates change with weekly GI and plastic input rates, so avoid relying on an old quotation.

Next steps

First, review your winter minimum temperatures and the crop stage that overlaps with cold nights. If cold stress has repeatedly affected yield or harvest timing, request and compare a thermic-film specification against a standard UV-stabilised film of the same thickness and useful features.

Then fix leakage points and decide your night curtain and humidity routine. For a new naturally ventilated structure, it also helps to understand what an NVPH is and plan roof ventilation, side curtains and crop choice together. Thermic polyfilm works best as part of this full system, not as a stand-alone solution.

Frequently asked questions

Can thermic polyfilm protect crops from frost?

It can reduce radiative heat loss on clear nights and may lower frost risk inside a closed polyhouse. It cannot guarantee protection during severe or prolonged cold, particularly where air leaks or ventilation openings remain open.

Is thermic polyfilm useful in a naturally ventilated polyhouse?

Yes, it can be useful in an NVPH if the side curtains, doors and film edges can be closed reasonably well at night. The benefit reduces when the house must remain open for humidity control or because of poor sealing.

Does thermic polyfilm reduce sunlight for crops?

That depends on the complete film formulation, including whether it is clear or diffused and what other additives are used. Ask for the film’s light-transmission and diffusion details rather than assuming all thermic films behave the same way.

Can I use thermic polyfilm in summer?

A thermic property mainly helps with night heat retention and does not solve summer daytime heat stress. For hot months, ventilation, shade management, roof height, orientation and, where suitable, cooling systems are more important.

Should I choose anti-drip or thermic polyfilm?

These are not always either-or choices, because a film can be made with both properties. Choose anti-drip where roof condensation and droplet fall are a crop concern, and choose thermic performance where cold nights are a proven production constraint.

Build your kit