How Pests Enter a Polyhouse: Find and Fix Every Entry Point
Polyhouse Constructions Agronomy Desk · 12 Nov 2026
A polyhouse does not stop pests simply because it is covered. Pests enter through working openings such as doors and vents, through damage in the cover or insect net, and by hitchhiking on seedlings, crates, tools and people. Start by checking the entrance and side ventilation, then inspect the full perimeter, roof and crop-input movement. Fix the largest and most active entry routes before reacting with crop-protection sprays.
Start with the pest pattern, not the damaged leaves
The location and timing of the first infestation often point to how pests enter polyhouse structures.
Walk through the house at least once a week, preferably early morning when insects are less active and the crop is easier to inspect. Carry a torch, marker tape, a notebook and a few spare clips or repair patches. Check yellow and blue sticky traps as well as plants. Record the first affected bay, side and row.
Use these clues as a first diagnosis:
What you observe | Likely entry route to check first | What it may indicate |
|---|---|---|
Sticky traps catch insects close to the main entrance | Door use, door gap, visitor movement | Whiteflies, aphids and thrips may be entering during frequent access |
More insects on the windward side or near side vents | Side insect net, curtain seals, torn net | Wind-driven entry through gaps or poorly seated curtains |
Insects concentrated near fan-end or pad-end walls | Fan and pad openings, shutters, seals | Airflow is drawing insects towards an unprotected or damaged opening |
Infestation begins soon after planting | Nursery plants, trays, crates or planting labour | Pests or eggs arrived with incoming material |
A small hotspot keeps returning in one corner | Tear, floor-level gap, weeds or rubbish nearby | A local harbourage or repeated entry point is present |
Mites or soil pests occur without many insects on traps | Planting material, soil, weeds or internal spread | Not every pest arrived through an opening |
A trap catch does not prove the exact opening, but it tells you where to inspect closely. Mark damaged spots immediately. A tiny hole that looks harmless can become an important route when there is a strong pressure difference, wind or repeated movement through that section.
Inspect the entrance first: the highest-risk route
The main door is often the biggest pest entry point because it is used many times each day. A good insect net elsewhere cannot compensate for a door that stays open during harvesting, packing or irrigation work.
Check the door operation
Stand outside and look at the closed door from all sides. Then stand inside and look for daylight around the frame. Inspect:
- Gap under the door, especially where the ground has settled or the floor is uneven.
- Gaps along both vertical edges and at the top corners.
- Door frame distortion, loose hinges, broken latches or a door that does not self-close.
- Torn net on a screened door or loose net fastening.
- Wide opening created when workers carry harvest crates, stakes or long tools.
- Weeds, discarded crop material or volunteer plants around the entrance.
Even a well-made door becomes weak if workers prop it open. Do not use bricks, buckets or rope to hold it open during harvest. Bring crates in batches and close the door between batches.
Use a double-door routine where pressure is high
A double-door entry area, also called a vestibule or insect-proof lobby, reduces direct movement from outside to crop. Only one door should be open at a time. It is particularly useful for cucumber, capsicum, tomato and flower crops that are vulnerable to virus-carrying whiteflies, thrips and aphids.
Read more about double-door entry systems for polyhouse biosecurity. The system works only if all workers follow it. Put a clear instruction board at the entrance in the local language used by your team.
Trace every ventilation opening and air path
Naturally ventilated polyhouses need side ventilation and roof vents. These openings are necessary for crop climate, but they must be consistently protected with suitable insect net and correctly sealed at the edges.
Side curtains, roll-up sections and roof vents
Start at one corner and walk the complete perimeter. Inspect outside and inside. Look especially where nets meet GI pipes, end walls, curtain rails and overlap joints.
Check for:
- Net lifted from the bottom or sides when the curtain is rolled up or down.
- Loose stitching, clips, profiles or fasteners along the net edge.
- A gap where the roll-up curtain does not meet the lower fixed section.
- Open corners near the gutter, roof vent or end wall.
- Net rubbing against metal edges and developing a line of wear.
- Bent pipes or sagging supports that stop the curtain from closing evenly.
Operate each curtain fully once during the inspection. A gap may not be visible when the curtain is in only one position. Do this after high winds and before the monsoon, when loose fittings and damaged edges can worsen quickly.
The correct net is only one part of exclusion. Net condition, fit and sealing determine whether it performs in practice. For selection factors and trade-offs, see this guide to insect-proof net selection. If a side net needs replacement, inspect the full fastening line rather than patching only the visibly damaged centre. Individual side insect net material is available for repairs or planned replacement.
Fan and pad polyhouse checks
In a fan and pad structure, air is deliberately pulled through the house. This means the intake side, pad frame, fan shutters and all service penetrations need close attention.
Inspect the pad-end frame for side gaps, incomplete seals and openings created during maintenance. Inspect fan shutters to ensure they close when fans are off. Look for net damage or missing screens at any intake, louvre or service opening. Never block required air movement just to stop insects; poor ventilation can create humidity problems and disease. Repair or screen the opening while retaining the designed airflow.
For differences in ventilation and pest risk, compare NVPH and fan-and-pad polyhouses.
Find tears, gaps and hidden openings in the cover
Do a slow exterior inspection after sunrise or near sunset. At low-angle light, holes and loose areas are easier to see. Then inspect from inside with the doors closed. A helper outside can shine a torch along suspect joints after dark to reveal pinholes and gaps.
Where damage commonly starts
Do not inspect only the middle of the polyfilm or net. Damage commonly begins at contact points:
- At clamps, zig-zag profiles, channels and overlap edges.
- Where polyfilm or net rubs against a sharp GI edge, wire, bolt or trellis support.
- At roof corners and around gutters where rainwater and wind load act repeatedly.
- Near the ground where rodents, dogs, machinery or workers can damage the cover.
- Around pipes, cables, irrigation mainlines and sensor wiring that pass through the wall.
- Around old repair patches with lifting edges.
For a pinhole in polyfilm, use a compatible repair method and clean, dry surface. For net damage, a proper patch with enough overlap is more reliable than a quick knot. Replace a severely weakened section rather than repeatedly patching it. A patch must sit flat; curled edges create another opening.
Also check that external shade-net support, trellis wires and crop strings do not rub the cover in wind. Prevention is cheaper than waiting for a small abrasion to become a large tear in the rainy season.
Do not overlook seedlings, workers and farm materials
A structurally sound polyhouse can still receive pests through daily operations. Whiteflies, aphids, thrips, mites and their eggs can arrive on nursery plants, leaf surfaces, trays and weeds attached to materials.
Seedlings are a common starting point
Before accepting seedlings, inspect the undersides of leaves, growing points, tray cells and the outer rows of every batch. Reject or isolate plants with live insects, eggs, suspicious leaf curl, stippling, honeydew, viral symptoms or severe uneven growth.
Keep new seedlings away from the main crop for observation when practical. Do not move nursery trays directly from an open area into the polyhouse without inspection. This seedling health checklist can help you check a batch before entry.
Set a simple people-and-material movement rule
Workers and visitors do not usually bring flying pests on clothing in the same way as an open door does. But they can carry infested leaves, nursery plants, tools, crates and crop waste. Their movement can also transfer pests from one infected bay to a clean bay.
Use these rules:
- Enter the youngest or cleanest crop block first, then older or affected blocks.
- Do not carry removed infested plants through clean rows unnecessarily.
- Keep harvest crates clean and stored away from weeds and discarded crop residues.
- Clean pruning tools between blocks, especially where virus symptoms are suspected.
- Restrict unnecessary visitors, and ask workers not to bring plants from home gardens into the structure.
- Keep crop waste in a closed or designated removal route, not at the entrance.
Virus diseases can be especially costly because a few viruliferous insects may spread infection quickly. For crop-level precautions, refer to tomato leaf curl virus management in polyhouses.
Check the outside zone that feeds pests into the house
Pest exclusion starts several metres outside the structure. Tall weeds, abandoned crop residues, unmanaged nursery plants and piles of waste near vents or doors can maintain whiteflies, aphids, thrips, leaf miners and mites.
Walk around the whole outer perimeter and inspect:
- Weeds touching side nets or growing around end walls.
- Volunteer tomato, chilli, brinjal, cucurbit or ornamental plants.
- Old crop residues and cull piles.
- Nearby open cultivation carrying the same host crop.
- Standing water, broken drainage lines and wet corners that complicate sanitation.
- Night lighting near entrances, which can attract some flying insects.
Keep a clean, low-weed strip around the polyhouse. Do not place waste heaps near the windward wall or entrance. Where pest pressure comes from neighbouring fields, increase trap monitoring on that side and tighten door discipline during high-risk operations.
Run a 30-minute entry-point audit after every risk event
Do not wait for a visible outbreak. Inspect after heavy wind, storms, net repair, construction work, a new planting, or a sudden rise in sticky-trap catches.
Use this inspection sequence:
- Review traps: Note which traps have fresh catches and where they are located.
- Inspect the entrance: Close the door and check all four edges, latch and screened sections.
- Walk the perimeter: Check side curtains, net joints, ground edges and end walls.
- Look upward: Inspect roof vents, gutter areas, cover fasteners and rubbing points.
- Operate moving parts: Raise and lower each curtain; open and close doors, shutters and fans as applicable.
- Check incoming items: Inspect seedlings, trays, crates and tools before they enter.
- Remove outside pest sources: Clear weeds and crop waste around doors and vents.
- Record and repair: Photograph each defect, mark its location and note the repair date.
Prioritise repairs as follows: first, an open door or major net tear; second, gaps around side curtains and vent edges; third, small tears likely to enlarge; and finally, cosmetic cover damage that is fully sealed. If trap catches continue after repair, repeat the audit at a different time of day and inspect the crop for an internal source of breeding.
Sticky traps help show where pests are entering and building up, but they are not a complete control measure. Use them alongside regular crop scouting. See how to scout pests in a polyhouse every week for a practical scouting routine.
Next steps
This week, inspect the main door, the windward side net and all moving curtains first. Mark every gap, tear and loose fitting, then repair the most direct openings before the next crop operation. Make entry-point checks part of weekly scouting and repeat them after storms or any major material movement.
If you need replacement covers, nets, fittings or other structure material, you can build a material kit and view this week’s live rates. Check every item and quantity before ordering so the repair matches your structure and opening dimensions.
Frequently asked questions
Can insects enter through insect net in a polyhouse?
Yes. They can enter if the net is torn, poorly fastened, lifted at the edges or unsuitable for the pest pressure. Insects may also enter whenever curtains or doors are opened, so net condition alone is not enough.
Why are whiteflies appearing near my polyhouse door?
Frequent door opening, gaps below the door and weeds or host crops outside are common reasons. Check traps and crop plants near the entry first, then inspect the door seal and worker movement routine.
Do I need to close side curtains all the time to prevent pests?
Not necessarily. Closing ventilation too much can raise heat and humidity, which harms crop health. Keep curtains operating as needed for climate, but ensure the fixed and moving net sections meet properly without gaps.
How often should I inspect polyhouse insect net and polyfilm?
Make a quick check part of weekly scouting and carry out a detailed inspection after high winds, storms or repairs. Check before planting too, because it is easier to repair openings when the crop is absent.
Can pests come into a polyhouse with purchased seedlings?
Yes. Eggs, nymphs, adults and mites can arrive on seedlings, trays and leaf surfaces, and infected plants can introduce viruses. Inspect each batch before entry and keep questionable plants separate from the main crop.
