How to Inspect Polyhouse Frame Welding Quality: A Farmer’s Checklist
Polyhouse Constructions Agronomy Desk · 13 Nov 2026
A polyhouse welding quality check is a practical visual inspection of every welded joint, pipe alignment and zinc protection before the crop cover goes on. Do not accept a frame simply because the weld looks thick or has been painted. A good joint is continuous where required, properly fused to both members, free from obvious defects, aligned with the drawing and protected against corrosion.
Carry out the check in daylight. Ask the fabricator or erection supervisor to keep the approved layout, member schedule and material documents available. For a large project, high-wind site or a frame with any doubtful welds, involve a qualified structural engineer before acceptance.
What to inspect and when
Welding may be done in a factory on items such as truss pieces, braces, brackets and base components. On many polyhouse designs, the main on-site assembly is bolted. This is useful because excessive field welding on galvanised (GI) pipe damages the zinc coating and can make later corrosion more likely.
Inspect at three stages:
- Before dispatch or unloading: Check fabricated members on the ground, preferably at the factory or immediately upon delivery.
- During erection: Check that members have been installed in the correct position and that no site welding has been added without approval.
- Before polyfilm, shade net or insect net installation: Walk through the completed bare frame. This is the easiest time to spot crooked bays, sharp weld spatter and missing bracing.
Take dated photographs of each issue, including one wide image to show its location and one close image with a scale or tape. Mark the bay number, row and side of the structure. A verbal complaint after the cover is fitted is harder to resolve.
Inspection stage | What you can see best | Action if there is a concern |
|---|---|---|
Fabricated member on ground | Weld bead finish, pipe burn-through, bracket position, coating damage | Segregate the member; do not send it into erection until reviewed |
Frame partly erected | Verticality, truss level, brace location and member orientation | Pause work in that bay and compare with approved drawing |
Bare completed structure | Overall straightness, sharp edges, roof symmetry and loose connections | Rectify before film, net, gutters and curtains are fitted |
After first rain or wind | Movement, water collection near joints, coating damage and loosening | Record the issue and arrange a technical inspection promptly |
The right pipe specification matters as much as welding. Read the GI pipe sizes used in polyhouse construction alongside the project drawing, rather than judging frame strength only by appearance.
Weld finish: the visible signs of a sound joint
A weld joins steel by fusion. The weld bead should form a neat, reasonably even connection between the two parts. Its exact appearance differs with pipe thickness, joint type and welding process, so do not reject a member only because every bead does not look identical. Look instead for clear defects.
Good visible signs
At a normal viewing distance, a satisfactory weld normally has these features:
- The weld runs continuously over the intended joint area. It does not stop halfway where the design calls for a continuous weld.
- The bead joins both pipes, plates or brackets without an obvious gap at either edge.
- The pipe ends fit closely before welding. A weld should not be used to fill a large careless gap between badly cut members.
- There are no sharp protrusions that can cut hands, polyfilm or netting.
- Brackets sit flat and are not visibly twisted after welding.
- The surrounding pipe is not badly burnt, crushed or thinned.
Defects a farmer can identify
Use a torch where needed and inspect all around the pipe, not only the side facing outward.
Visible defect | What it looks like | Why it needs attention |
|---|---|---|
Crack | A fine line in the weld or beside it, sometimes starting at the end of a bead | A crack can grow under wind movement and is not acceptable |
Porosity | Small pinholes or a sponge-like surface | May indicate trapped gas or contamination and reduces weld soundness |
Undercut | A groove melted into the parent pipe along the edge of the weld | It reduces section at a stressed location |
Overlap or cold-looking bead | Metal appears laid on the pipe edge without blending into it | May show poor fusion between weld and pipe |
Burn-through | A hole, very thin patch or heavily scorched area in the pipe | Weakens the tube and opens zinc protection |
Excess spatter | Sharp balls or droplets around the joint | Can tear covers and signals poor finishing |
A thick, rough bead is not automatically a strong weld. Likewise, a smooth bead alone does not prove internal fusion. Visual inspection is a screening method, not a laboratory test. If cracks, repeated pores, burn-through, or a doubtful load-bearing truss joint is found, ask for assessment by the fabricator’s welding supervisor or an independent competent inspector. Do not attempt a hammer, bend or load test on the installed frame yourself; it can cause damage and does not reliably certify the joint.
Check alignment, geometry and member placement
Even a good weld is a problem if it fixes the wrong geometry. A skewed truss or mislocated brace changes how wind and roof loads travel through the frame.
Start with the approved drawing. Check the span, bay spacing, gutter line, ridge line, columns, cross-bracing and door framing against it. Do not rely on another nearby polyhouse as a reference; dimensions vary by design, wind zone, crop system and local rainfall.
A simple field method
Use a tape, long string line, spirit level or laser level. You do not need to calculate structural capacity, but you can identify obvious deviations.
- Stand at one end and sight along each column row. Columns should form a straight line without a noticeable lean or dog-leg.
- Check whether the gutter line is visually straight and whether adjoining trusses sit at the same level.
- Measure diagonals across selected rectangular bays. Large differences between diagonal measurements indicate a racked or out-of-square bay.
- Check that roof arches or trusses repeat the intended profile. A distorted arch can pull polyfilm unevenly.
- Compare brace positions with the drawing. Braces should not be missing, moved to one side, loosely welded or cut short to force them into place.
- Confirm that brackets, purlins and curtain supports face the required direction. A reversed bracket can create cover-fitting issues.
Do not assume a frame will straighten after polyfilm is tensioned. Cover tension may hide minor visual issues but cannot correct a structural alignment error. It can also impose uneven pull on clips and arches. For roof profile considerations before construction, see how to choose a polyhouse shape and roof profile.
Pay special attention to high-stress joints
Not every weld carries the same load. Give extra time to joints where wind, roof weight, curtain movement or equipment loads concentrate.
Inspect these locations carefully:
- Column-to-base and column-to-foundation connections: Check member position, base plate seating, weld finish and fastening arrangement. Foundations and anchors must match the approved plan.
- Column-to-truss or arch connections: These transfer roof loads into vertical supports. Look for incomplete welds, distorted brackets and mismatched members.
- Truss apex and rafter joints: At the ridge, poorly fitted parts or cracked welds can affect the roof shape.
- Bracing end connections: Braces only work when both ends are securely connected in the intended direction.
- Gutter supports and rainwater members: In high-rainfall areas, these joints face repeated water and load exposure. Read how to design polyhouse gutters for heavy rain if this is a concern for your site.
- Fan, pad, door and curtain frames: These may carry vibration or repeated operational loads. Check for loose brackets and sharp weld edges.
Never approve an unplanned cut, notch or welded patch in a primary column, truss or brace without written approval from the design authority. A small modification made to accommodate a door, pipe or equipment line can weaken a critical member.
Check the GI coating after welding and repair work
GI pipe resists corrosion because of its zinc coating. Welding heats the steel and burns away zinc close to the joint. Grinding, drilling, transport scratches and field cutting can do the same. Therefore, the weld zone needs proper cleaning and a suitable zinc-rich cold-galvanising repair system or another approved touch-up method.
Inspect each welded or cut area for the following:
- Bare black or blue steel left exposed.
- Red-brown rust already forming near the heat-affected zone.
- Flaking, poorly adhering or uneven touch-up coating.
- Deep grinder marks beyond the immediate weld cleanup area.
- Paint used merely to hide poor welds or rust.
- Water traps at brackets, caps or overlapping members.
Touch-up should be dry, continuous and fully cover exposed steel, but it should not conceal cracks, pores or a bad joint. Ask what repair method was used and whether it is compatible with galvanised steel. In coastal areas, humid belts and locations where fertiliser water regularly splashes on the frame, this check is particularly important. See how to stop rust on polyhouse GI pipe frames for ongoing maintenance.
A clean frame also protects the cover. Remove weld spatter and smooth sharp points before fitting the polyfilm. A 250-micron film can still tear where it rubs against an abrasive point in wind.
Acceptance checklist for farmers and site supervisors
Print this list or use it on your phone. Tick only after physically checking the member or bay.
For supplied material, retain dispatch records, technical data sheets and any test certificates. Polyhouse Constructions provides a technical data sheet for each product and lab test certificates with dispatch; these records help you compare delivered material with the order. You can also build a material kit with item-wise quantities when planning a new structure.
When to stop work and call a technical person
Stop work in the affected bay rather than trying a quick patch if you see a crack in a main truss, column or brace; repeated weld defects across several members; significant frame lean; an incorrectly placed brace; or a welded modification not shown in the drawing.
A repair should have a clear method: identify the cause, remove or repair defective material as recommended, restore alignment, protect exposed GI steel and reinspect. Simply adding another weld over a crack can trap the defect and make future inspection difficult.
High-wind, coastal, hilly and heavy-rain locations need more careful review because forces and corrosion exposure are greater. The frame design must suit the site. Refer to how wind load changes polyhouse structure design before accepting substitutions or reducing bracing.
Next steps
Inspect the bare frame before any polyfilm or net goes up. Use the checklist bay by bay, photograph defects and obtain written closure for every correction. Then keep the inspection record with the drawing, invoices and warranty documents.
After handover, include weld zones, coating touch-ups, braces and fasteners in an annual inspection. Early repair of coating damage is usually simpler than dealing with corrosion or a loose joint after several monsoons.
Frequently asked questions
Can I judge polyhouse weld strength only by looking at it?
No. Visual inspection can reveal cracks, poor finish, burn-through and incomplete-looking joints, but it cannot confirm internal fusion or design capacity. If a critical joint is doubtful, ask for review by a competent welding or structural professional.
Is field welding on GI polyhouse pipe acceptable?
It may be necessary for approved details or repairs, but it should be limited and controlled. Welding burns the zinc coating, so the affected area needs suitable corrosion repair after cleaning, and any unplanned structural modification needs design approval.
Should every polyhouse connection be welded?
No. Many structures use a combination of factory-welded components and bolted site connections. The correct joint type depends on the approved structural design, transport arrangement and erection method.
What should I do if weld spatter is touching the polyfilm area?
Have sharp spatter carefully removed and the surface made smooth before the cover is installed. Inspect the cleaned area for exposed steel and ensure its corrosion protection is restored where required.
How often should welds and GI coating be checked after installation?
Inspect at least once a year and after severe wind, heavy rain or any impact to the frame. Check sooner in coastal or highly humid areas, and where fertigation water or chemicals may splash onto steel.
